-- Journal begins at Sun 2022-08-07 15:25:09 CEST, ends at Tue 2024-05-28 16:29:04 CEST. -- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] Linux version 6.6.0-1-librem5 (XXX@XXX) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Mon May 6 16:09:52 EDT 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Purism Librem 5r4 [ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable m7@40000000 [ 0.000000] OF: reserved mem: 0x0000000080000000..0x00000000807fffff (8192 KiB) nomap non-reusable rproc@80000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff] node 0: [mem 0x0000000041000000-0x000000007fffffff] node 0: [mem 0x0000000080000000-0x00000000807fffff] node 0: [mem 0x0000000080800000-0x00000000ffffffff] Initmem setup node 0 [mem 0x0000000040000000-0x00000000ffffffff] cma: Reserved 320 MiB at 0x00000000e7600000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 29 pages/cpu s80488 r8192 d30104 u118784 [ 0.000000] pcpu-alloc: s80488 r8192 d30104 u118784 alloc=29*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation forced OFF by mitigations=off [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: u_boot_version=2022.10-g9d134279b6 console=ttymxc0,115200 quiet fsck.repair=yes security=apparmor splash plymouth.ignore-serial-consoles vt.global_cursor_default=0 [ 0.000000] Unknown kernel command line parameters "splash u_boot_version=2022.10-g9d134279b6", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 774144 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x00000000e2f8c000-0x00000000e6f8c000] (64MB) [ 0.000000] Memory: 2618284K/3145728K available (13440K kernel code, 2754K rwdata, 4864K rodata, 5056K init, 643K bss, 199764K reserved, 327680K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 43518 entries in 170 pages [ 0.000000] ftrace: allocated 170 pages with 4 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 128 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec0311ec, max_idle_ns: 440795202152 ns [ 0.000000] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255541ns [ 0.000588] Console: colour dummy device 80x25 [ 0.000631] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333) [ 0.000644] pid_max: default: 32768 minimum: 301 [ 0.000751] LSM: initializing lsm=capability,apparmor [ 0.000843] AppArmor: AppArmor initialized [ 0.000946] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.000972] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.001950] spectre-v4 mitigation disabled by command-line option [ 0.002951] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.003035] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.003154] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.003366] rcu: Hierarchical SRCU implementation. [ 0.003370] rcu: Max phase no-delay instances is 1000. [ 0.004731] smp: Bringing up secondary CPUs ... [ 0.005400] Detected VIPT I-cache on CPU1 [ 0.005464] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 [ 0.005511] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] Detected VIPT I-cache on CPU2 [ 0.006276] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 [ 0.006301] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] Detected VIPT I-cache on CPU3 [ 0.007036] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 [ 0.007059] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] smp: Brought up 1 node, 4 CPUs [ 0.007149] SMP: Total of 4 processors activated. [ 0.007155] CPU features: detected: 32-bit EL0 Support [ 0.007159] CPU features: detected: CRC32 instructions [ 0.007229] CPU: All CPU(s) started at EL2 [ 0.007232] alternatives: applying system-wide alternatives [ 0.009157] devtmpfs: initialized [ 0.020423] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.020443] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.030719] pinctrl core: initialized pinctrl subsystem [ 0.031954] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.033166] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.033405] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.033701] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.034387] thermal_sys: Registered thermal governor 'step_wise' [ 0.034393] thermal_sys: Registered thermal governor 'power_allocator' [ 0.034433] cpuidle: using governor menu [ 0.034673] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.034774] ASID allocator initialised with 65536 entries [ 0.034947] Serial: AMBA PL011 UART driver [ 0.042784] platform XXX@XXX: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000/soc-uid@4 [ 0.043376] amba 28440000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.043522] amba 28540000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.043663] amba 28640000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.043812] amba 28740000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.043964] amba 28740000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.044091] amba 28640000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.044196] amba 28540000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.044312] amba 28440000.etm: Fixed dependency cycle(s) with /soc@0/funnel [ 0.044393] platform XXX@XXX:funnel: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 [ 0.044411] platform XXX@XXX:funnel: Fixed dependency cycle(s) with /soc@0/etm@28740000 [ 0.044484] platform XXX@XXX:funnel: Fixed dependency cycle(s) with /soc@0/etm@28640000 [ 0.044562] platform XXX@XXX:funnel: Fixed dependency cycle(s) with /soc@0/etm@28540000 [ 0.044633] platform XXX@XXX:funnel: Fixed dependency cycle(s) with /soc@0/etm@28440000 [ 0.044817] platform XXX@XXX:funnel: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 [ 0.044895] amba 28c03000.funnel: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.044936] amba 28c03000.funnel: Fixed dependency cycle(s) with /soc@0/funnel [ 0.045115] amba 28c03000.funnel: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.045185] amba 28c04000.etf: Fixed dependency cycle(s) with /soc@0/etr@28c06000 [ 0.045231] amba 28c04000.etf: Fixed dependency cycle(s) with /soc@0/funnel@28c03000 [ 0.045396] amba 28c04000.etf: Fixed dependency cycle(s) with /soc@0/etr@28c06000 [ 0.045507] amba 28c06000.etr: Fixed dependency cycle(s) with /soc@0/etf@28c04000 [ 0.047298] platform 30320000.lcd-controller: Fixed dependency cycle(s) with /soc@0/bus@30800000/dsi@30a00000 [ 0.047484] platform 30330000.pinctrl: Fixed dependency cycle(s) with /soc@0/bus@30000000/pinctrl@30330000/hoggrp [ 0.048197] imx8mq-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver [ 0.048931] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.049525] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.050784] platform 30380000.clock-controller: Fixed dependency cycle(s) with /soc@0/bus@30000000/gpc@303a0000 [ 0.051135] platform 30380000.clock-controller: Fixed dependency cycle(s) with /soc@0/bus@30000000/gpc@303a0000 [ 0.051958] platform 303a0000.gpc: Fixed dependency cycle(s) with /soc@0/interrupt-controller@38800000 [ 0.056407] platform 30320000.lcd-controller: Fixed dependency cycle(s) with /soc@0/bus@30800000/dsi@30a00000 [ 0.056498] platform 30a00000.dsi: Fixed dependency cycle(s) with /soc@0/bus@30800000/dsi@30a00000/panel@0 [ 0.056526] platform 30a00000.dsi: Fixed dependency cycle(s) with /soc@0/bus@30000000/lcd-controller@30320000 [ 0.059340] platform 30a70000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a40000/camera@20 [ 0.059367] platform 30a70000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30a90000 [ 0.059685] platform 30a70000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30a90000 [ 0.059794] platform 30a90000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30a70000 [ 0.060197] platform 30b60000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a50000/camera@2d [ 0.060220] platform 30b60000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30b80000 [ 0.060538] platform 30b60000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30b80000 [ 0.060641] platform 30b80000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30b60000 [ 0.062688] platform 32c00000.hdmi: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32e00000 [ 0.062943] platform 32c00000.hdmi: Fixed dependency cycle(s) with /soc@0/bus@32c00000/display-controller@32e00000 [ 0.063038] platform 32e00000.display-controller: Fixed dependency cycle(s) with /soc@0/bus@32c00000/hdmi@32c00000 [ 0.063961] platform 38100000.usb: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a20000/usb-pd@3f/connector [ 0.073540] Modules: 26032 pages in range for non-PLT usage [ 0.073547] Modules: 517552 pages in range for PLT usage [ 0.074341] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.074348] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.074355] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.074360] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.074367] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.074373] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.074380] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.074385] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.074998] cryptd: max_cpu_qlen set to 1000 [ 0.076722] iommu: Default domain type: Translated [ 0.076727] iommu: DMA domain TLB invalidation policy: strict mode [ 0.076831] reg-fixed-voltage regulator-vdd-sen: using DT '/regulator-vdd-sen' for '(null)' GPIO lookup [ 0.076853] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-vdd-sen[0]' [ 0.076871] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vdd-sen[0]' [ 0.076883] reg-fixed-voltage regulator-vdd-sen: using lookup tables for GPIO lookup [ 0.076891] reg-fixed-voltage regulator-vdd-sen: No GPIO consumer (null) found [ 0.077008] SCSI subsystem initialized [ 0.077047] libata version 3.00 loaded. [ 0.077221] reg-fixed-voltage regulator-vdd-3v3: using DT '/regulator-vdd-3v3' for '(null)' GPIO lookup [ 0.077241] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-vdd-3v3[0]' [ 0.077259] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vdd-3v3[0]' [ 0.077270] reg-fixed-voltage regulator-vdd-3v3: using lookup tables for GPIO lookup [ 0.077276] reg-fixed-voltage regulator-vdd-3v3: No GPIO consumer (null) found [ 0.077596] reg-fixed-voltage regulator-vsys-3v4: using DT '/regulator-vsys-3v4' for '(null)' GPIO lookup [ 0.077614] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-vsys-3v4[0]' [ 0.077641] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vsys-3v4[0]' [ 0.077653] reg-fixed-voltage regulator-vsys-3v4: using lookup tables for GPIO lookup [ 0.077661] reg-fixed-voltage regulator-vsys-3v4: No GPIO consumer (null) found [ 0.077898] pps_core: LinuxPPS API ver. 1 registered [ 0.077902] pps_core: Software ver. 5.3.6 - Copyright FAF7-631D Rodolfo Giometti <XXX@XXX> [ 0.077917] PTP clock support registered [ 0.079284] vgaarb: loaded [ 0.079532] clocksource: Switched to clocksource arch_sys_counter [ 1.096120] VFS: Disk quotas dquot_6.6.0 [ 1.096169] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.096695] AppArmor: AppArmor Filesystem Enabled [ 1.105443] NET: Registered PF_INET protocol family [ 1.105675] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 1.109095] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 1.109173] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.109191] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 1.109447] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) [ 1.110476] TCP: Hash tables configured (established 32768 bind 32768) [ 1.110589] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 1.110681] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 1.110891] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.111387] RPC: Registered named UNIX socket transport module. [ 1.111393] RPC: Registered udp transport module. [ 1.111396] RPC: Registered tcp transport module. [ 1.111399] RPC: Registered tcp-with-tls transport module. [ 1.111403] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.111418] PCI: CLS 0 bytes, default 64 [ 1.111762] Unpacking initramfs... [ 1.113027] Initialise system trusted keyrings [ 1.113181] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.113226] zbud: loaded [ 1.113571] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.114123] NFS: Registering the id_resolver key type [ 1.114151] Key type id_resolver registered [ 1.114156] Key type id_legacy registered [ 1.114178] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.114190] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.145713] jitterentropy: Initialization failed with host not compliant with requirements: 9 [ 1.145743] Key type asymmetric registered [ 1.145749] Asymmetric key parser 'x509' registered [ 1.145854] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.159585] SoC: i.MX8MQ revision 2.1 [ 1.167880] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.170937] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 15, base_baud = 1562500) is a IMX [ 1.170986] printk: console [ttymxc0] enabled [ 1.171912] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 16, base_baud = 1562500) is a IMX [ 1.172626] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 17, base_baud = 1562500) is a IMX [ 1.172824] serial serial0: tty port ttymxc1 registered [ 1.173290] imx-uart 30a60000.serial: using DT '/soc@0/bus@30800000/serial@30a60000' for 'rs485-term' GPIO lookup [ 1.173315] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/soc@0/bus@30800000/serial@30a60000[0]' [ 1.173340] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/soc@0/bus@30800000/serial@30a60000[0]' [ 1.173360] imx-uart 30a60000.serial: using lookup tables for GPIO lookup [ 1.173369] imx-uart 30a60000.serial: No GPIO consumer rs485-term found [ 1.173377] imx-uart 30a60000.serial: using DT '/soc@0/bus@30800000/serial@30a60000' for 'rs485-rx-during-tx' GPIO lookup [ 1.173396] of_get_named_gpiod_flags: can't parse 'rs485-rx-during-tx-gpios' property of node '/soc@0/bus@30800000/serial@30a60000[0]' [ 1.173418] of_get_named_gpiod_flags: can't parse 'rs485-rx-during-tx-gpio' property of node '/soc@0/bus@30800000/serial@30a60000[0]' [ 1.173433] imx-uart 30a60000.serial: using lookup tables for GPIO lookup [ 1.173442] imx-uart 30a60000.serial: No GPIO consumer rs485-rx-during-tx found [ 1.173638] 30a60000.serial: ttymxc3 at MMIO 0x30a60000 (irq = 18, base_baud = 1562500) is a IMX [ 1.182191] loop: module loaded [ 1.183889] mdio_bus fixed-0: using lookup tables for GPIO lookup [ 1.183904] mdio_bus fixed-0: No GPIO consumer reset found [ 1.184858] i2c_dev: i2c /dev entries driver [ 1.187138] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: XXX@XXX [ 1.188862] sdhci: Secure Digital Host Controller Interface driver [ 1.188870] sdhci: Copyright(c) Pierre Ossman [ 1.188896] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.189785] leds-gpio leds: using DT '/leds/chg-en' for '(null)' GPIO lookup [ 1.189814] leds-gpio leds: No GPIO consumer (null) found [ 1.189944] leds-gpio not_really_leds: using DT '/not_really_leds/smc-boot' for '(null)' GPIO lookup [ 1.189969] leds-gpio not_really_leds: No GPIO consumer (null) found [ 1.190404] ledtrig-cpu: registered to indicate activity on CPUs [ 1.190703] hid: raw HID events driver (C) Jiri Kosina [ 1.192234] imx-bus-devfreq 32700000.interconnect: passive parent node /soc@0/memory-controller@3d400000 [ 1.194346] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 1.197124] imx_ocotp 30350000.efuse: using DT '/soc@0/bus@30000000/efuse@30350000' for 'wp' GPIO lookup [ 1.197151] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc@0/bus@30000000/efuse@30350000[0]' [ 1.197173] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc@0/bus@30000000/efuse@30350000[0]' [ 1.197190] imx_ocotp 30350000.efuse: using lookup tables for GPIO lookup [ 1.197198] imx_ocotp 30350000.efuse: No GPIO consumer wp found [ 1.197297] platform XXX@XXX: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000 [ 1.198928] NET: Registered PF_LLC protocol family [ 1.199073] NET: Registered PF_PACKET protocol family [ 1.199845] 9pnet: Installing 9P2000 support [ 1.199903] Key type dns_resolver registered [ 1.207920] registered taskstats version 1 [ 1.208078] Loading compiled-in X.509 certificates [ 1.219566] Key type .fscrypt registered [ 1.219586] Key type fscrypt-provisioning registered [ 1.219828] AppArmor: AppArmor sha1 policy hashing enabled [ 1.234597] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.234630] gpio gpiochip0: (30200000.gpio): created GPIO range 0->29 ==> 30330000.pinctrl PIN 10->39 [ 1.234661] gpio gpiochip0: Persistence not supported for GPIO 1 [ 1.234671] gpio-1 (pmic-5v-hog): hogged as input [ 1.235413] gpio gpiochip0: (30200000.gpio): added GPIO chardev (254:0) [ 1.235424] gpio gpiochip0: registered GPIOs 0 to 31 on 30200000.gpio [ 1.237036] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.237054] gpio gpiochip1: (30210000.gpio): created GPIO range 0->20 ==> 30330000.pinctrl PIN 40->60 [ 1.237716] gpio gpiochip1: (30210000.gpio): added GPIO chardev (254:1) [ 1.237727] gpio gpiochip1: registered GPIOs 32 to 63 on 30210000.gpio [ 1.239216] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.239232] gpio gpiochip2: (30220000.gpio): created GPIO range 0->25 ==> 30330000.pinctrl PIN 61->86 [ 1.239910] gpio gpiochip2: (30220000.gpio): added GPIO chardev (254:2) [ 1.239921] gpio gpiochip2: registered GPIOs 64 to 95 on 30220000.gpio [ 1.241422] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.241438] gpio gpiochip3: (30230000.gpio): created GPIO range 0->31 ==> 30330000.pinctrl PIN 87->118 [ 1.242099] gpio gpiochip3: (30230000.gpio): added GPIO chardev (254:3) [ 1.242110] gpio gpiochip3: registered GPIOs 96 to 127 on 30230000.gpio [ 1.243631] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.243647] gpio gpiochip4: (30240000.gpio): created GPIO range 0->29 ==> 30330000.pinctrl PIN 119->148 [ 1.244134] gpio gpiochip4: (30240000.gpio): added GPIO chardev (254:4) [ 1.244145] gpio gpiochip4: registered GPIOs 128 to 159 on 30240000.gpio [ 1.245811] reg-fixed-voltage regulator-audio-1v8: using DT '/regulator-audio-1v8' for '(null)' GPIO lookup [ 1.245837] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-audio-1v8[0]' [ 1.245882] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-audio-1v8[0]' - status (0) [ 1.245914] gpio gpiochip0: Persistence not supported for GPIO 4 [ 1.246215] reg-fixed-voltage regulator-mic-2v4: using DT '/regulator-mic-2v4' for '(null)' GPIO lookup [ 1.246239] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-mic-2v4[0]' [ 1.246258] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-mic-2v4[0]' [ 1.246273] reg-fixed-voltage regulator-mic-2v4: using lookup tables for GPIO lookup [ 1.246281] reg-fixed-voltage regulator-mic-2v4: No GPIO consumer (null) found [ 1.246585] reg-fixed-voltage regulator-csi-1v8: using DT '/regulator-csi-1v8' for '(null)' GPIO lookup [ 1.246605] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-csi-1v8[0]' [ 1.246639] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-csi-1v8[0]' - status (0) [ 1.246663] gpio gpiochip0: Persistence not supported for GPIO 0 [ 1.246971] reg-fixed-voltage regulator-vcam-2v8: using DT '/regulator-vcam-2v8' for '(null)' GPIO lookup [ 1.246990] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-vcam-2v8[0]' [ 1.247019] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-vcam-2v8[0]' - status (0) [ 1.247034] gpio-0 (regulator-csi-1v8): gpiod_request: status -16 [ 1.247044] reg-fixed-voltage regulator-vcam-2v8: nonexclusive access to GPIO for (null) [ 1.247085] imx-i2c 30a20000.i2c: using DT '/soc@0/bus@30800000/i2c@30a20000' for 'sda' GPIO lookup [ 1.247108] of_get_named_gpiod_flags: can't parse 'sda-gpios' property of node '/soc@0/bus@30800000/i2c@30a20000[0]' [ 1.247129] of_get_named_gpiod_flags: can't parse 'sda-gpio' property of node '/soc@0/bus@30800000/i2c@30a20000[0]' [ 1.247145] imx-i2c 30a20000.i2c: using lookup tables for GPIO lookup [ 1.247152] imx-i2c 30a20000.i2c: No GPIO consumer sda found [ 1.247159] imx-i2c 30a20000.i2c: using DT '/soc@0/bus@30800000/i2c@30a20000' for 'scl' GPIO lookup [ 1.247178] of_get_named_gpiod_flags: can't parse 'scl-gpios' property of node '/soc@0/bus@30800000/i2c@30a20000[0]' [ 1.247198] of_get_named_gpiod_flags: can't parse 'scl-gpio' property of node '/soc@0/bus@30800000/i2c@30a20000[0]' [ 1.247213] imx-i2c 30a20000.i2c: using lookup tables for GPIO lookup [ 1.247219] imx-i2c 30a20000.i2c: No GPIO consumer scl found [ 1.247314] reg-fixed-voltage regulator-gnss: using DT '/regulator-gnss' for '(null)' GPIO lookup [ 1.247332] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-gnss[0]' [ 1.247362] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-gnss[0]' - status (0) [ 1.247400] gpio gpiochip2: Persistence not supported for GPIO 12 [ 1.247685] reg-fixed-voltage regulator-hub: using DT '/regulator-hub' for '(null)' GPIO lookup [ 1.247702] reg-fixed-voltage regulator-lcd-3v4: using DT '/regulator-lcd-3v4' for '(null)' GPIO lookup [ 1.247705] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-hub[0]' [ 1.247721] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-lcd-3v4[0]' [ 1.247732] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-hub[0]' - status (0) [ 1.247749] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-lcd-3v4[0]' - status (0) [ 1.247756] gpio gpiochip0: Persistence not supported for GPIO 14 [ 1.247771] gpio gpiochip0: Persistence not supported for GPIO 20 [ 1.263817] rtc-m41t80 0-0068: registered as rtc0 [ 1.265163] rtc-m41t80 0-0068: setting system clock to 2024-05-27T19:55:30 UTC (1716839730) [ 1.265242] i2c i2c-0: IMX I2C adapter registered [ 1.266272] imx-i2c 30a30000.i2c: using DT '/soc@0/bus@30800000/i2c@30a30000' for 'sda' GPIO lookup [ 1.266300] of_get_named_gpiod_flags: can't parse 'sda-gpios' property of node '/soc@0/bus@30800000/i2c@30a30000[0]' [ 1.266322] of_get_named_gpiod_flags: can't parse 'sda-gpio' property of node '/soc@0/bus@30800000/i2c@30a30000[0]' [ 1.266338] imx-i2c 30a30000.i2c: using lookup tables for GPIO lookup [ 1.266346] imx-i2c 30a30000.i2c: No GPIO consumer sda found [ 1.266354] imx-i2c 30a30000.i2c: using DT '/soc@0/bus@30800000/i2c@30a30000' for 'scl' GPIO lookup [ 1.266372] of_get_named_gpiod_flags: can't parse 'scl-gpios' property of node '/soc@0/bus@30800000/i2c@30a30000[0]' [ 1.266392] of_get_named_gpiod_flags: can't parse 'scl-gpio' property of node '/soc@0/bus@30800000/i2c@30a30000[0]' [ 1.266408] imx-i2c 30a30000.i2c: using lookup tables for GPIO lookup [ 1.266415] imx-i2c 30a30000.i2c: No GPIO consumer scl found [ 1.267353] tps65132 1-003e: using DT '/soc@0/bus@30800000/i2c@30a30000/regulator@3e/outp' for 'enable' GPIO lookup [ 1.267380] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/soc@0/bus@30800000/i2c@30a30000/regulator@3e/outp[0]' [ 1.267405] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/soc@0/bus@30800000/i2c@30a30000/regulator@3e/outp[0]' [ 1.267425] tps65132 1-003e: No GPIO consumer enable found [ 1.267971] i2c i2c-1: IMX I2C adapter registered [ 1.268226] tps65132 1-003e: using DT '/soc@0/bus@30800000/i2c@30a30000/regulator@3e/outn' for 'enable' GPIO lookup [ 1.268251] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/soc@0/bus@30800000/i2c@30a30000/regulator@3e/outn[0]' [ 1.268277] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/soc@0/bus@30800000/i2c@30a30000/regulator@3e/outn[0]' [ 1.268296] tps65132 1-003e: No GPIO consumer enable found [ 1.268934] imx-i2c 30a40000.i2c: using DT '/soc@0/bus@30800000/i2c@30a40000' for 'sda' GPIO lookup [ 1.268958] of_get_named_gpiod_flags: can't parse 'sda-gpios' property of node '/soc@0/bus@30800000/i2c@30a40000[0]' [ 1.268979] of_get_named_gpiod_flags: can't parse 'sda-gpio' property of node '/soc@0/bus@30800000/i2c@30a40000[0]' [ 1.268995] imx-i2c 30a40000.i2c: using lookup tables for GPIO lookup [ 1.269002] imx-i2c 30a40000.i2c: No GPIO consumer sda found [ 1.269009] imx-i2c 30a40000.i2c: using DT '/soc@0/bus@30800000/i2c@30a40000' for 'scl' GPIO lookup [ 1.269028] of_get_named_gpiod_flags: can't parse 'scl-gpios' property of node '/soc@0/bus@30800000/i2c@30a40000[0]' [ 1.269048] of_get_named_gpiod_flags: can't parse 'scl-gpio' property of node '/soc@0/bus@30800000/i2c@30a40000[0]' [ 1.269063] imx-i2c 30a40000.i2c: using lookup tables for GPIO lookup [ 1.269070] imx-i2c 30a40000.i2c: No GPIO consumer scl found [ 1.270280] platform 30a70000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a40000/camera@20 [ 1.270426] i2c 2-0020: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30a70000 [ 1.271551] i2c i2c-2: IMX I2C adapter registered [ 1.272461] imx-i2c 30a50000.i2c: using DT '/soc@0/bus@30800000/i2c@30a50000' for 'sda' GPIO lookup [ 1.272485] of_get_named_gpiod_flags: can't parse 'sda-gpios' property of node '/soc@0/bus@30800000/i2c@30a50000[0]' [ 1.272507] of_get_named_gpiod_flags: can't parse 'sda-gpio' property of node '/soc@0/bus@30800000/i2c@30a50000[0]' [ 1.272524] imx-i2c 30a50000.i2c: using lookup tables for GPIO lookup [ 1.272532] imx-i2c 30a50000.i2c: No GPIO consumer sda found [ 1.272539] imx-i2c 30a50000.i2c: using DT '/soc@0/bus@30800000/i2c@30a50000' for 'scl' GPIO lookup [ 1.272559] of_get_named_gpiod_flags: can't parse 'scl-gpios' property of node '/soc@0/bus@30800000/i2c@30a50000[0]' [ 1.272579] of_get_named_gpiod_flags: can't parse 'scl-gpio' property of node '/soc@0/bus@30800000/i2c@30a50000[0]' [ 1.272594] imx-i2c 30a50000.i2c: using lookup tables for GPIO lookup [ 1.272603] imx-i2c 30a50000.i2c: No GPIO consumer scl found [ 1.273682] platform 30b60000.csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a50000/camera@2d [ 1.273821] i2c 3-002d: Fixed dependency cycle(s) with /soc@0/bus@30800000/csi@30b60000 [ 1.274944] i2c i2c-3: IMX I2C adapter registered [ 1.275912] reg-fixed-voltage regulator-wifi-3v3: using DT '/regulator-wifi-3v3' for '(null)' GPIO lookup [ 1.275937] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-wifi-3v3[0]' [ 1.275973] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-wifi-3v3[0]' - status (0) [ 1.276001] gpio gpiochip2: Persistence not supported for GPIO 10 [ 1.280242] etnaviv etnaviv: bound 38000000.gpu (ops gpu_ops) [ 1.280308] etnaviv-gpu 38000000.gpu: model: GC7000, revision: 6214 [ 1.280804] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 [ 1.282566] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 3 mkt segment 0 supported-hw 0x8 0x1 [ 1.284273] pwrseq_simple pwrseq: using DT '/pwrseq' for 'reset' GPIO lookup [ 1.284313] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/pwrseq[0]' - status (0) [ 1.284344] gpio gpiochip2: Persistence not supported for GPIO 25 [ 1.284359] pwrseq_simple pwrseq: using DT '/pwrseq' for 'reset' GPIO lookup [ 1.284385] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/pwrseq[1]' - status (0) [ 1.284429] gpio gpiochip3: Persistence not supported for GPIO 29 [ 1.285302] leds-gpio leds: using DT '/leds/chg-en' for '(null)' GPIO lookup [ 1.285326] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/chg-en[0]' - status (0) [ 1.285344] gpio gpiochip2: Persistence not supported for GPIO 2 [ 1.285349] gpio-66 (?): no flags found for (null) [ 1.285420] leds-gpio leds: using DT '/leds/hub-nreset' for '(null)' GPIO lookup [ 1.285444] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/hub-nreset[0]' - status (0) [ 1.285460] gpio gpiochip0: Persistence not supported for GPIO 12 [ 1.285464] gpio-12 (?): no flags found for (null) [ 1.285515] leds-gpio leds: using DT '/leds/sd-en' for '(null)' GPIO lookup [ 1.285533] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/sd-en[0]' - status (0) [ 1.285547] gpio gpiochip0: Persistence not supported for GPIO 3 [ 1.285552] gpio-3 (?): no flags found for (null) [ 1.285600] leds-gpio leds: using DT '/leds/gnss-nreset' for '(null)' GPIO lookup [ 1.285618] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/gnss-nreset[0]' - status (0) [ 1.285632] gpio gpiochip0: Persistence not supported for GPIO 8 [ 1.285636] gpio-8 (?): no flags found for (null) [ 1.285680] sdhci-esdhc-imx 30b50000.mmc: using DT '/soc@0/bus@30800000/mmc@30b50000' for 'cd' GPIO lookup [ 1.285691] leds-gpio leds: using DT '/leds/smc-en' for '(null)' GPIO lookup [ 1.285702] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/soc@0/bus@30800000/mmc@30b50000[0]' [ 1.285714] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/smc-en[0]' - status (0) [ 1.285721] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/soc@0/bus@30800000/mmc@30b50000[0]' [ 1.285731] gpio gpiochip0: Persistence not supported for GPIO 6 [ 1.285733] sdhci-esdhc-imx 30b50000.mmc: using lookup tables for GPIO lookup [ 1.285735] gpio-6 (?): no flags found for (null) [ 1.285739] sdhci-esdhc-imx 30b50000.mmc: No GPIO consumer cd found [ 1.285746] sdhci-esdhc-imx 30b50000.mmc: using DT '/soc@0/bus@30800000/mmc@30b50000' for 'wp' GPIO lookup [ 1.285759] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc@0/bus@30800000/mmc@30b50000[0]' [ 1.285773] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc@0/bus@30800000/mmc@30b50000[0]' [ 1.285783] sdhci-esdhc-imx 30b50000.mmc: using lookup tables for GPIO lookup [ 1.285784] leds-gpio leds: using DT '/leds/wwan-en' for '(null)' GPIO lookup [ 1.285788] sdhci-esdhc-imx 30b50000.mmc: No GPIO consumer wp found [ 1.285814] sdhci-esdhc-imx 30b50000.mmc: allocated mmc-pwrseq [ 1.285812] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/wwan-en[0]' - status (0) [ 1.285828] gpio gpiochip2: Persistence not supported for GPIO 18 [ 1.285832] gpio-82 (?): no flags found for (null) [ 1.285911] leds-gpio leds: using DT '/leds/wwan-nreset' for '(null)' GPIO lookup [ 1.285929] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/wwan-nreset[0]' - status (0) [ 1.285943] gpio gpiochip2: Persistence not supported for GPIO 1 [ 1.285948] gpio-65 (?): no flags found for (null) [ 1.285997] leds-gpio leds: using DT '/leds/wwan-disable' for '(null)' GPIO lookup [ 1.286015] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/wwan-disable[0]' - status (0) [ 1.286029] gpio gpiochip2: Persistence not supported for GPIO 16 [ 1.286034] gpio-80 (?): no flags found for (null) [ 1.286089] leds-gpio leds: using DT '/leds/wwan-dis2' for '(null)' GPIO lookup [ 1.286107] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/wwan-dis2[0]' - status (0) [ 1.286122] gpio gpiochip2: Persistence not supported for GPIO 13 [ 1.286126] gpio-77 (?): no flags found for (null) [ 1.286600] leds-gpio not_really_leds: using DT '/not_really_leds/smc-boot' for '(null)' GPIO lookup [ 1.286623] of_get_named_gpiod_flags: parsed 'gpios' property of node '/not_really_leds/smc-boot[0]' - status (0) [ 1.286657] gpio gpiochip4: Persistence not supported for GPIO 29 [ 1.286662] gpio-157 (?): no flags found for (null) [ 1.287018] imx8m-ddrc-devfreq 3d400000.memory-controller: measure bandwidth with pmu imx8_ddr0 [ 1.287298] imx8m-ddrc-devfreq 3d400000.memory-controller: Disable unsupported OPP 166935483Hz 668MT/s [ 1.287821] reg-fixed-voltage regulator-vdd-1v8: using DT '/regulator-vdd-1v8' for '(null)' GPIO lookup [ 1.287836] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-vdd-1v8[0]' [ 1.287848] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vdd-1v8[0]' [ 1.287857] reg-fixed-voltage regulator-vdd-1v8: using lookup tables for GPIO lookup [ 1.287863] reg-fixed-voltage regulator-vdd-1v8: No GPIO consumer (null) found [ 1.289754] reg-fixed-voltage regulator-vcam-1v2: using DT '/regulator-vcam-1v2' for '(null)' GPIO lookup [ 1.289780] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-vcam-1v2[0]' [ 1.289793] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vcam-1v2[0]' [ 1.289803] reg-fixed-voltage regulator-vcam-1v2: using lookup tables for GPIO lookup [ 1.289808] reg-fixed-voltage regulator-vcam-1v2: No GPIO consumer (null) found [ 1.289889] lm3692x 2-0036: using DT '/soc@0/bus@30800000/i2c@30a40000/backlight@36' for 'enable' GPIO lookup [ 1.289919] of_get_named_gpiod_flags: parsed 'enable-gpios' property of node '/soc@0/bus@30800000/i2c@30a40000/backlight@36[0]' - status (0) [ 1.289947] gpio gpiochip2: Persistence not supported for GPIO 14 [ 1.290032] sdhci-esdhc-imx 30b40000.mmc: using DT '/soc@0/bus@30800000/mmc@30b40000' for 'wp' GPIO lookup [ 1.290049] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc@0/bus@30800000/mmc@30b40000[0]' [ 1.290065] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc@0/bus@30800000/mmc@30b40000[0]' [ 1.290077] sdhci-esdhc-imx 30b40000.mmc: using lookup tables for GPIO lookup [ 1.290082] sdhci-esdhc-imx 30b40000.mmc: No GPIO consumer wp found [ 1.290135] reg-fixed-voltage regulator-lcd-1v8: using DT '/regulator-lcd-1v8' for '(null)' GPIO lookup [ 1.290149] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/regulator-lcd-1v8[0]' [ 1.290170] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-lcd-1v8[0]' - status (0) [ 1.290186] gpio gpiochip0: Persistence not supported for GPIO 5 [ 1.294491] led-backlight backlight-dsi: Not enough levels defined [ 1.295090] nwl-dsi 30a00000.dsi: Fixed dependency cycle(s) with /soc@0/bus@30800000/dsi@30a00000/panel@0 [ 1.295236] mipi-dsi 30a00000.dsi.0: Fixed dependency cycle(s) with /soc@0/bus@30800000/dsi@30a00000 [ 1.295464] panel-mantix-mlaf057we51 30a00000.dsi.0: using DT '/soc@0/bus@30800000/dsi@30a00000/panel@0' for 'reset' GPIO lookup [ 1.295495] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/soc@0/bus@30800000/dsi@30a00000/panel@0[0]' - status (0) [ 1.295684] gpio gpiochip0: Persistence not supported for GPIO 29 [ 1.295696] panel-mantix-mlaf057we51 30a00000.dsi.0: using DT '/soc@0/bus@30800000/dsi@30a00000/panel@0' for 'mantix,tp-rstn' GPIO lookup [ 1.295718] of_get_named_gpiod_flags: parsed 'mantix,tp-rstn-gpios' property of node '/soc@0/bus@30800000/dsi@30a00000/panel@0[0]' - status (0) [ 1.295735] gpio gpiochip0: Persistence not supported for GPIO 24 [ 1.295964] nwl-dsi 30a00000.dsi: [drm:nwl_dsi_host_attach] lanes=4, format=0x0 flags=0x7 [ 1.295981] panel-mantix-mlaf057we51 30a00000.dsi.0: 720x1440@63 24bpp dsi 4dl - ready [ 1.296130] nwl-dsi 30a00000.dsi: [drm:nwl_dsi_probe] Using LCDIF as input source [ 1.297694] [drm] Initialized mxsfb-drm 1.0.0 20160824 for 30320000.lcd-controller on minor 1 [ 1.315544] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA [ 1.340099] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA [ 1.449740] mmc0: new HS400 MMC card at address 0001 [ 1.451424] mmcblk0: mmc0:0001 032GB2 29.1 GiB [ 1.454272] mmcblk0: p1 p2 [ 1.456356] mmcblk0boot0: mmc0:0001 032GB2 4.00 MiB [ 1.457985] mmcblk0boot1: mmc0:0001 032GB2 4.00 MiB [ 1.458977] mmcblk0rpmb: mmc0:0001 032GB2 4.00 MiB, chardev (245:0) [ 1.495589] Console: switching to colour frame buffer device 90x90 [ 1.518064] mxsfb 30320000.lcd-controller: [drm] fb0: mxsfb-drmdrmfb frame buffer device [ 1.521653] gpio-keys gpio-keys: using DT '/gpio-keys/wwan_wake' for '(null)' GPIO lookup [ 1.521697] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/wwan_wake[0]' - status (0) [ 1.521724] gpio gpiochip2: Persistence not supported for GPIO 15 [ 1.521763] gpio-keys gpio-keys: using DT '/gpio-keys/key-vol-down' for '(null)' GPIO lookup [ 1.521783] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/key-vol-down[0]' - status (0) [ 1.521799] gpio gpiochip0: Persistence not supported for GPIO 17 [ 1.521829] gpio-keys gpio-keys: using DT '/gpio-keys/key-vol-up' for '(null)' GPIO lookup [ 1.521846] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/key-vol-up[0]' - status (0) [ 1.521861] gpio gpiochip0: Persistence not supported for GPIO 16 [ 1.521985] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 1.523789] input: bd718xx-pwrkey as /devices/platform/soc@0/30800000.bus/30a20000.i2c/i2c-0/0-004b/gpio-keys.0.auto/input/input1 [ 1.524111] clk: Disabling unused clocks [ 1.813717] Freeing initrd memory: 19676K [ 1.817376] Freeing unused kernel memory: 5056K [ 1.817462] Run /init as init process [ 1.817466] with arguments: [ 1.817471] /init [ 1.817475] splash [ 1.817479] with environment: [ 1.817482] HOME=/ [ 1.817485] TERM=linux [ 1.817488] u_boot_version=2022.10-g9d134279b6 [ 2.181669] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input2 [ 2.188369] imx-sdma 302c0000.dma-controller: loaded firmware 4.5 [ 2.227828] imx8mq-usb-phy 381f0040.usb-phy: supply vbus not found, using dummy regulator [ 2.240562] imx-sdma 30bd0000.dma-controller: loaded firmware 4.5 [ 2.260289] spi_master spi0: using DT '/soc@0/bus@30800000/spi@30820000' for 'cs' GPIO lookup [ 2.260335] of_get_named_gpiod_flags: parsed 'cs-gpios' property of node '/soc@0/bus@30800000/spi@30820000[0]' - status (0) [ 2.260361] gpio gpiochip4: Persistence not supported for GPIO 9 [ 2.278441] bq25890-charger 3-006a: using DT '/soc@0/bus@30800000/i2c@30a50000/charger@6a' for 'otg' GPIO lookup [ 2.278502] of_get_named_gpiod_flags: parsed 'otg-gpios' property of node '/soc@0/bus@30800000/i2c@30a50000/charger@6a[0]' - status (0) [ 2.278534] gpio gpiochip2: Persistence not supported for GPIO 4 [ 2.278546] bq25890-charger 3-006a: Got otg gpio hack [ 2.318880] bq25890-charger 3-006a: using DT '/soc@0/bus@30800000/i2c@30a50000/charger@6a' for 'otg' GPIO lookup [ 2.318937] of_get_named_gpiod_flags: parsed 'otg-gpios' property of node '/soc@0/bus@30800000/i2c@30a50000/charger@6a[0]' - status (0) [ 2.319171] gpio gpiochip2: Persistence not supported for GPIO 4 [ 2.319185] bq25890-charger 3-006a: Got otg gpio hack [ 2.320199] bq25890-charger 3-006a: No battery found: -19 [ 2.320232] bq25890-charger 3-006a: Upstream supply changed: 0. [ 2.320243] bq25890-charger 3-006a: Disabling OTG_EN pin [ 2.323333] spi-nor spi0.0: using DT '/soc@0/bus@30800000/spi@30820000/flash@0' for 'reset' GPIO lookup [ 2.323369] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc@0/bus@30800000/spi@30820000/flash@0[0]' [ 2.323387] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/soc@0/bus@30800000/spi@30820000/flash@0[0]' [ 2.323401] spi-nor spi0.0: using lookup tables for GPIO lookup [ 2.323407] spi-nor spi0.0: No GPIO consumer reset found [ 2.325483] cdns-mhdp-imx 32c00000.hdmi: [drm:cdns_mhdp_read_fw_version [cdns_mhdp_drmcore]] firmware version: 50d385ac [ 2.327511] imx-dcss 32e00000.display-controller: bound 32c00000.hdmi (ops cdns_mhdp_imx_ops [cdns_mhdp_imx]) [ 2.327899] [drm] Initialized imx-dcss 1.0.0 20190917 for 32e00000.display-controller on minor 2 [ 2.328948] [drm] Connector status: 0 [ 2.329029] imx-dcss 32e00000.display-controller: [drm] Cannot find any crtc or sizes [ 2.329512] spi-nor spi0.0: s25fl016k (2048 Kbytes) [ 2.330272] [drm] Connector status: 0 [ 2.330309] imx-dcss 32e00000.display-controller: [drm] Cannot find any crtc or sizes [ 2.331200] usbcore: registered new interface driver usbfs [ 2.331245] usbcore: registered new interface driver hub [ 2.331302] usbcore: registered new device driver usb [ 2.339896] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller [ 2.339930] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 1 [ 2.340033] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe6c hci version 0x110 quirks 0x0000008000000010 [ 2.340088] xhci-hcd xhci-hcd.4.auto: irq 208, io mem 0x38200000 [ 2.340227] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller [ 2.340251] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 2 [ 2.340262] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 SuperSpeed [ 2.340389] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06 [ 2.340414] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 2.340421] usb usb1: Product: xHCI Host Controller [ 2.340425] usb usb1: Manufacturer: Linux 6.6.0-1-librem5 xhci-hcd [ 2.340430] usb usb1: SerialNumber: ... [ 2.341019] hub 1-0:1.0: USB hub found [ 2.341043] hub 1-0:1.0: 1 port detected [ 2.341402] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.341500] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06 [ 2.341508] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 2.341514] usb usb2: Product: xHCI Host Controller [ 2.341519] usb usb2: Manufacturer: Linux 6.6.0-1-librem5 xhci-hcd [ 2.341523] usb usb2: SerialNumber: ... [ 2.342007] hub 2-0:1.0: USB hub found [ 2.342029] hub 2-0:1.0: 1 port detected [ 2.344411] 2 fixed-partitions partitions found on MTD device spi0.0 [ 2.344428] Creating 2 MTD partitions on "spi0.0": [ 2.344434] 0x000000000000-0x000000030000 : "protected0" [ 2.345193] 0x000000030000-0x000000200000 : "firmware" [ 2.599576] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.747683] usb 1-1: New USB device found, idVendor=0424, idProduct=2640, bcdDevice= 9.02 [ 2.747699] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=... [ 2.788517] hub 1-1:1.0: USB hub found [ 2.788580] hub 1-1:1.0: 3 ports detected [ 3.175565] usb 1-1.1: new high-speed USB device number 3 using xhci-hcd [ 3.382731] usb 1-1.1: New USB device found, idVendor=0424, idProduct=4041, bcdDevice= 2.09 [ 3.382747] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=... [ 3.382753] usb 1-1.1: Product: Ultra Fast Media Reader [ 3.382758] usb 1-1.1: Manufacturer: Generic [ 3.382763] usb 1-1.1: SerialNumber: ... [ 3.391043] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 3.392826] scsi host0: usb-storage 1-1.1:1.0 [ 3.393136] usbcore: registered new interface driver usb-storage [ 3.394214] usbcore: registered new interface driver uas [ 4.244062] random: crng init done [ 4.423009] scsi 0:0:0:0: Direct-Access Generic Ultra HS-SD/MMC 2.09 PQ: 0 ANSI: 0 [ 4.425505] sd 0:0:0:0: [sda] 61407232 512-byte logical blocks: (31.4 GB/29.3 GiB) [ 4.426158] sd 0:0:0:0: [sda] Write Protect is off [ 4.426168] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 4.426761] sd 0:0:0:0: [sda] No Caching mode page found [ 4.426767] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 4.436006] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.436020] GPT:11718749 != 61407231 [ 4.436027] GPT:Alternate GPT header not at the end of the disk. [ 4.436030] GPT:11718749 != 61407231 [ 4.436033] GPT: Use GNU Parted to correct GPT errors. [ 4.436056] sda: sda1 sda2 sda3 [ 4.436579] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 4.686387] EXT4-fs (mmcblk0p2): mounted filesystem HASH_84F-3BA2-3470-32DF-EFF38050B9BA ro with ordered data mode. Quota mode: none. [ 4.809428] EXT4-fs (mmcblk0p2): re-mounted HASH_84F-3BA2-3470-32DF-EFF38050B9BA r/w. Quota mode: none. [ 5.279827] NET: Registered PF_INET6 protocol family [ 5.282071] Segment Routing with IPv6 [ 5.282090] In-situ OAM (IOAM) with IPv6 [ 5.756338] zram: Added device: zram0 [ 6.194845] fuse: init (API version 7.39) [ 6.260662] EXT4-fs (mmcblk0p2): re-mounted HASH_84F-3BA2-3470-32DF-EFF38050B9BA r/w. Quota mode: none. [ 7.035740] remoteproc remoteproc0: imx-rproc is available [ 7.121781] rfkill-hks rfkill-hks: using DT '/rfkill-hks/mic-hks' for '(null)' GPIO lookup [ 7.121829] of_get_named_gpiod_flags: parsed 'gpios' property of node '/rfkill-hks/mic-hks[0]' - status (0) [ 7.121858] gpio gpiochip3: Persistence not supported for GPIO 1 [ 7.122098] rfkill-hks rfkill-hks: using DT '/rfkill-hks/camera-hks' for '(null)' GPIO lookup [ 7.122484] of_get_named_gpiod_flags: parsed 'gpios' property of node '/rfkill-hks/camera-hks[0]' - status (0) [ 7.122506] gpio-97 (mic-hks): gpiod_request: status -16 [ 7.122514] rfkill-hks rfkill-hks: nonexclusive access to GPIO for (null) [ 7.124928] caam 30900000.crypto: Entropy delay = 3200 [ 7.125026] caam 30900000.crypto: Entropy delay = 3600 [ 7.138942] caam 30900000.crypto: Instantiated RNG4 SH0 [ 7.152853] caam 30900000.crypto: Instantiated RNG4 SH1 [ 7.152884] caam 30900000.crypto: device ID = 0x0a16040100000000 (Era 9) [ 7.152891] caam 30900000.crypto: job rings = 2, qi = 0 [ 7.155662] rfkill-hks rfkill-hks: using DT '/rfkill-hks/wlan-hks' for '(null)' GPIO lookup [ 7.155708] of_get_named_gpiod_flags: parsed 'gpios' property of node '/rfkill-hks/wlan-hks[0]' - status (0) [ 7.155737] gpio gpiochip3: Persistence not supported for GPIO 10 [ 7.173629] rfkill-hks rfkill-hks: using DT '/rfkill-hks/wwan-hks' for '(null)' GPIO lookup [ 7.173679] of_get_named_gpiod_flags: parsed 'gpios' property of node '/rfkill-hks/wwan-hks[0]' - status (0) [ 7.173708] gpio gpiochip3: Persistence not supported for GPIO 0 [ 7.269441] gnss: GNSS driver registered with major 241 [ 7.289586] mc: Linux media interface: v0.10 [ 7.307274] videodev: Linux video capture interface: v2.00 [ 7.338086] s5k3l6xx 3-002d: using default 24000000 Hz clock frequency [ 7.338111] s5k3l6xx 3-002d: using DT '/soc@0/bus@30800000/i2c@30a50000/camera@2d' for 'rstn' GPIO lookup [ 7.338156] of_get_named_gpiod_flags: parsed 'rstn-gpios' property of node '/soc@0/bus@30800000/i2c@30a50000/camera@2d[0]' - status (0) [ 7.338185] gpio gpiochip0: Persistence not supported for GPIO 26 [ 7.338207] s5k3l6xx 3-002d: probe i2c ffff00000209ec00 [ 7.355146] imx7-csi 30a90000.csi: Registered csi capture as /dev/video0 [ 7.370496] lm3560-led 1-0053: using DT '/soc@0/bus@30800000/i2c@30a30000/flash@53' for 'enable' GPIO lookup [ 7.370546] of_get_named_gpiod_flags: parsed 'enable-gpios' property of node '/soc@0/bus@30800000/i2c@30a30000/flash@53[0]' - status (0) [ 7.370576] gpio gpiochip0: Persistence not supported for GPIO 23 [ 7.371676] dw9714 3-000c: I2C write fail [ 7.372862] s5k3l6xx: i2c_read: error during transfer (-6) [ 7.375819] dw9714 3-000c: dw9714_vcm_suspend I2C failure: -5 [ 7.393640] imx7-csi 30b80000.csi: Registered csi capture as /dev/video1 [ 7.394578] wm8962_i2c_probe: 3681: defering probe [ 7.396441] hi846 2-0020: using DT '/soc@0/bus@30800000/i2c@30a40000/camera@20' for 'reset' GPIO lookup [ 7.396488] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/soc@0/bus@30800000/i2c@30a40000/camera@20[0]' - status (0) [ 7.396517] gpio gpiochip0: Persistence not supported for GPIO 25 [ 7.396528] hi846 2-0020: using DT '/soc@0/bus@30800000/i2c@30a40000/camera@20' for 'shutdown' GPIO lookup [ 7.396573] of_get_named_gpiod_flags: parsed 'shutdown-gpios' property of node '/soc@0/bus@30800000/i2c@30a40000/camera@20[0]' - status (0) [ 7.396592] gpio gpiochip4: Persistence not supported for GPIO 4 [ 7.416010] edt_ft5x06 2-0038: probing for EDT FT5x06 I2C [ 7.416266] edt_ft5x06 2-0038: supply iovcc not found, using dummy regulator [ 7.417042] edt_ft5x06 2-0038: using DT '/soc@0/bus@30800000/i2c@30a40000/touchscreen@38' for 'reset' GPIO lookup [ 7.417068] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc@0/bus@30800000/i2c@30a40000/touchscreen@38[0]' [ 7.417086] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/soc@0/bus@30800000/i2c@30a40000/touchscreen@38[0]' [ 7.417100] edt_ft5x06 2-0038: using lookup tables for GPIO lookup [ 7.417105] edt_ft5x06 2-0038: No GPIO consumer reset found [ 7.417111] edt_ft5x06 2-0038: using DT '/soc@0/bus@30800000/i2c@30a40000/touchscreen@38' for 'wake' GPIO lookup [ 7.417125] of_get_named_gpiod_flags: can't parse 'wake-gpios' property of node '/soc@0/bus@30800000/i2c@30a40000/touchscreen@38[0]' [ 7.417140] of_get_named_gpiod_flags: can't parse 'wake-gpio' property of node '/soc@0/bus@30800000/i2c@30a40000/touchscreen@38[0]' [ 7.417151] edt_ft5x06 2-0038: using lookup tables for GPIO lookup [ 7.417155] edt_ft5x06 2-0038: No GPIO consumer wake found [ 7.418504] wm8962_i2c_probe: 3681: defering probe [ 7.419857] edt_ft5x06 2-0038: verify id:0x8622 [ 7.419871] edt_ft5x06 2-0038: get ic information, chip id = 0x8622 [ 7.422580] edt_ft5x06 2-0038: Model "EP0700M09", Rev. "", 0x0 sensors [ 7.442378] input: EP0700M09 as /devices/platform/soc@0/30800000.bus/30a40000.i2c/i2c-2/2-0038/input/input3 [ 7.442584] edt_ft5x06 2-0038: fw upgrade init function [ 7.442677] edt_ft5x06 2-0038: EDT FT5x06 initialized: IRQ 51, WAKE pin -1, Reset pin -1. [ 7.448266] hi846 2-0020: i2c read error: -6 [ 7.475801] wm8962_i2c_probe: 3681: defering probe [ 7.529397] hi846: probe of 2-0020 failed with error -5 [ 7.541063] wm8962 2-001a: customer id 0 revision D [ 7.559990] debugfs: File 'Capture' in directory 'dapm' already present! [ 7.583137] pwm-vibrator vibrator: using DT '/vibrator' for 'enable' GPIO lookup [ 7.583178] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vibrator[0]' [ 7.583193] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vibrator[0]' [ 7.583202] pwm-vibrator vibrator: using lookup tables for GPIO lookup [ 7.583208] pwm-vibrator vibrator: No GPIO consumer enable found [ 7.583735] input: imx-audio-hdmi HDMI Jack as /devices/platform/sound-hdmi/sound/card0/input5 [ 7.589275] input: pwm-vibrator as /devices/platform/vibrator/input/input4 [ 7.601246] asoc-simple-card sound: using DT '/sound' for 'simple-audio-card,hp-det' GPIO lookup [ 7.601282] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpios' property of node '/sound[0]' [ 7.601313] of_get_named_gpiod_flags: parsed 'simple-audio-card,hp-det-gpio' property of node '/sound[0]' - status (0) [ 7.601339] gpio gpiochip2: Persistence not supported for GPIO 9 [ 7.601427] asoc-simple-card sound: using DT '/sound' for 'simple-audio-card,mic-det' GPIO lookup [ 7.601440] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpios' property of node '/sound[0]' [ 7.601452] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound[0]' [ 7.601461] asoc-simple-card sound: using lookup tables for GPIO lookup [ 7.601467] asoc-simple-card sound: No GPIO consumer simple-audio-card,mic-det found [ 7.602529] input: WM8962 Beep Generator as /devices/platform/soc@0/30800000.bus/30a40000.i2c/i2c-2/2-001a/input/input8 [ 7.627894] hantro-vpu 38300000.video-codec: registered nxp,imx8mq-vpu-g1-dec as /dev/video2 [ 7.631318] gpiochip_find_base: found new base at 512 [ 7.643509] hantro-vpu 38310000.video-codec: registered nxp,imx8mq-vpu-g2-dec as /dev/video3 [ 7.683677] gpio gpiochip5: (wm8962): added GPIO chardev (254:5) [ 7.683700] gpio gpiochip5: registered GPIOs 512 to 517 on wm8962 [ 7.699760] zram0: detected capacity change from 0 to 2969600 [ 7.766780] input: Librem 5 Headphones as /devices/platform/sound/sound/card1/input6 [ 7.791270] input: Librem 5 Headset Mic as /devices/platform/sound/sound/card1/input7 [ 7.792676] Adding 1484796k swap on /dev/zram0. Priority:100 extents:1 across:1484796k SS [ 7.802114] asoc-simple-card sound-wwan: using DT '/sound-wwan' for 'simple-audio-card,hp-det' GPIO lookup [ 7.802145] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpios' property of node '/sound-wwan[0]' [ 7.802159] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/sound-wwan[0]' [ 7.802169] asoc-simple-card sound-wwan: using lookup tables for GPIO lookup [ 7.802175] asoc-simple-card sound-wwan: No GPIO consumer simple-audio-card,hp-det found [ 7.802182] asoc-simple-card sound-wwan: using DT '/sound-wwan' for 'simple-audio-card,mic-det' GPIO lookup [ 7.802192] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpios' property of node '/sound-wwan[0]' [ 7.802204] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/sound-wwan[0]' [ 7.802212] asoc-simple-card sound-wwan: using lookup tables for GPIO lookup [ 7.802217] asoc-simple-card sound-wwan: No GPIO consumer simple-audio-card,mic-det found [ 8.303596] usb 1-1.2: new high-speed USB device number 4 using xhci-hcd [ 8.345796] caam algorithms registered in /proc/crypto [ 8.345954] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto [ 8.345965] caam 30900000.crypto: registering rng-caam [ 8.346889] caam 30900000.crypto: rng crypto API alg registered prng-caam [ 8.350377] mousedev: PS/2 mouse device common for all mice [ 8.395761] ext2 filesystem being mounted at /boot supports timestamps until 2038-01-19 (0x7fffffff) [ 8.505762] usb 1-1.2: New USB device found, idVendor=2020, idProduct=2060, bcdDevice= 0.00 [ 8.505785] usb 1-1.2: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 8.505791] usb 1-1.2: Product: Qualcomm CDMA Technologies MSM [ 8.505796] usb 1-1.2: Manufacturer: Qualcomm, Incorporated [ 8.676351] usbcore: registered new interface driver usbserial_generic [ 8.676405] usbserial: USB Serial support registered for generic [ 8.702399] usbcore: registered new interface driver cdc_wdm [ 8.705330] usbcore: registered new interface driver option [ 8.705684] usbserial: USB Serial support registered for GSM modem (1-port) [ 8.705967] option 1-1.2:1.0: GSM modem (1-port) converter detected [ 8.710645] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0 [ 8.711303] option 1-1.2:1.1: GSM modem (1-port) converter detected [ 8.711839] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1 [ 8.712057] option 1-1.2:1.2: GSM modem (1-port) converter detected [ 8.715645] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB2 [ 8.715947] option 1-1.2:1.3: GSM modem (1-port) converter detected [ 8.717385] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB3 [ 8.743405] qmi_wwan 1-1.2:1.4: cdc-wdm0: USB WDM device [ 8.746825] qmi_wwan 1-1.2:1.4 wwan0: register 'qmi_wwan' at usb-xhci-hcd.4.auto-1.2, WWAN/QMI device, XX:XX:XX:XX:XX:XX [ 8.749419] usbcore: registered new interface driver qmi_wwan [ 8.810303] iio iio:device3: DRDY on pin INT2 specified, but sensor does not support interrupts [ 8.816404] iio iio:device3: interrupts active high level [ 9.343837] configfs-gadget.g1 gadget.0: HOST MAC XX:XX:XX:XX:XX:XX [ 9.343859] configfs-gadget.g1 gadget.0: MAC XX:XX:XX:XX:XX:XX [ 13.273949] [drm] Connector status: 0 [ 16.913511] edt_ft5x06 2-0038: Unable to fetch data, error: -6 [ 18.243877] zram0: detected capacity change from 2969600 to 0