Wiphy phy0 wiphy index: 0 max # scan SSIDs: 20 max scan IEs length: 413 bytes max # sched scan SSIDs: 20 max # match sets: 11 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports RSN-IBSS. Device supports AP-side u-APSD. Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP-128 (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x3 RX 0x3 Configured Antennas: TX 0x3 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * monitor * P2P-client * P2P-GO * P2P-device Band 1: Capabilities: 0x11ef RX LDPC HT20/HT40 SM Power Save disabled RX HT20 SGI RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 4 usec (0x05) HT Max RX data rate: 300 Mbps HT TX/RX MCS rate indexes supported: 0-15 Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 2412.0 MHz [1] (22.0 dBm) * 2417.0 MHz [2] (22.0 dBm) * 2422.0 MHz [3] (22.0 dBm) * 2427.0 MHz [4] (22.0 dBm) * 2432.0 MHz [5] (22.0 dBm) * 2437.0 MHz [6] (22.0 dBm) * 2442.0 MHz [7] (22.0 dBm) * 2447.0 MHz [8] (22.0 dBm) * 2452.0 MHz [9] (22.0 dBm) * 2457.0 MHz [10] (22.0 dBm) * 2462.0 MHz [11] (22.0 dBm) * 2467.0 MHz [12] (22.0 dBm) * 2472.0 MHz [13] (22.0 dBm) * 2484.0 MHz [14] (disabled) Band 2: Capabilities: 0x11ef RX LDPC HT20/HT40 SM Power Save disabled RX HT20 SGI RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 4 usec (0x05) HT Max RX data rate: 300 Mbps HT TX/RX MCS rate indexes supported: 0-15 VHT Capabilities (0x039071b0): Max MPDU length: 3895 Supported Channel Width: neither 160 nor 80+80 RX LDPC short GI (80 MHz) TX STBC SU Beamformee MU Beamformee VHT RX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT RX highest supported: 0 Mbps VHT TX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT TX highest supported: 0 Mbps VHT extended NSS: supported Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Frequencies: * 5180.0 MHz [36] (22.0 dBm) (no IR) * 5200.0 MHz [40] (22.0 dBm) (no IR) * 5220.0 MHz [44] (22.0 dBm) (no IR) * 5240.0 MHz [48] (22.0 dBm) (no IR) * 5260.0 MHz [52] (22.0 dBm) (no IR, radar detection) * 5280.0 MHz [56] (22.0 dBm) (no IR, radar detection) * 5300.0 MHz [60] (22.0 dBm) (no IR, radar detection) * 5320.0 MHz [64] (22.0 dBm) (no IR, radar detection) * 5340.0 MHz [68] (disabled) * 5360.0 MHz [72] (disabled) * 5380.0 MHz [76] (disabled) * 5400.0 MHz [80] (disabled) * 5420.0 MHz [84] (disabled) * 5440.0 MHz [88] (disabled) * 5460.0 MHz [92] (disabled) * 5480.0 MHz [96] (disabled) * 5500.0 MHz [100] (22.0 dBm) (no IR, radar detection) * 5520.0 MHz [104] (22.0 dBm) (no IR, radar detection) * 5540.0 MHz [108] (22.0 dBm) (no IR, radar detection) * 5560.0 MHz [112] (22.0 dBm) (no IR, radar detection) * 5580.0 MHz [116] (22.0 dBm) (no IR, radar detection) * 5600.0 MHz [120] (22.0 dBm) (no IR, radar detection) * 5620.0 MHz [124] (22.0 dBm) (no IR, radar detection) * 5640.0 MHz [128] (22.0 dBm) (no IR, radar detection) * 5660.0 MHz [132] (22.0 dBm) (no IR, radar detection) * 5680.0 MHz [136] (22.0 dBm) (no IR, radar detection) * 5700.0 MHz [140] (22.0 dBm) (no IR, radar detection) * 5720.0 MHz [144] (22.0 dBm) (no IR, radar detection) * 5745.0 MHz [149] (22.0 dBm) * 5765.0 MHz [153] (22.0 dBm) * 5785.0 MHz [157] (22.0 dBm) * 5805.0 MHz [161] (22.0 dBm) * 5825.0 MHz [165] (22.0 dBm) * 5845.0 MHz [169] (disabled) * 5865.0 MHz [173] (disabled) * 5885.0 MHz [177] (disabled) * 5905.0 MHz [181] (disabled) Supported commands: * new_interface * set_interface * new_key * start_ap * new_station * new_mpath * set_mesh_config * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * frame * frame_wait_cancel * set_wiphy_netns * set_channel * start_sched_scan * probe_client * set_noack_map * register_beacons * start_p2p_device * set_mcast_rate * testmode * connect * disconnect * channel_switch * set_qos_map * add_tx_ts * set_multicast_to_unicast WoWLAN support: * wake up on disconnect * wake up on magic packet * wake up on pattern match, up to 20 patterns of 16-128 bytes, maximum packet offset 0 bytes * can do GTK rekeying * wake up on GTK rekey failure * wake up on EAP identity request * wake up on 4-way handshake * wake up on rfkill release * wake up on network detection, up to 11 match sets software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed } <= 1, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1, total <= 3, #channels <= 2 * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1, total <= 3, #channels <= 1 HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS. Device supports SAE with AUTHENTICATE command Device supports low priority scan. Device supports scan flush. Device supports per-vif TX power setting P2P GO supports CT window setting P2P GO supports opportunistic powersave setting Driver supports full state transitions for AP/GO clients Driver supports a userspace MPM Driver/device bandwidth changes during BSS lifetime (AP/GO mode) Device adds DS IE to probe requests Device can update TPC Report IE Device supports static SMPS Device supports dynamic SMPS Device supports WMM-AC admission (TSPECs) Device supports configuring vdev MAC-addr on create. Device supports randomizing MAC-addr in scans. Device supports randomizing MAC-addr in sched scans. Device supports randomizing MAC-addr in net-detect scans. max # scan plans: 2 max scan plan interval: 65535 max scan plan iterations: 254 Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xb0 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * P2P-device: 0x40 0xb0 0xd0 Supported extended features: * [ VHT_IBSS ]: VHT-IBSS * [ RRM ]: RRM * [ MU_MIMO_AIR_SNIFFER ]: MU-MIMO sniffer * [ SCAN_START_TIME ]: scan start timestamp * [ BSS_PARENT_TSF ]: BSS last beacon/probe TSF * [ BEACON_RATE_LEGACY ]: legacy beacon rate setting * [ FILS_STA ]: STA FILS (Fast Initial Link Setup) * [ FILS_MAX_CHANNEL_TIME ]: FILS max channel attribute override with dwell time * [ ACCEPT_BCAST_PROBE_RESP ]: accepts broadcast probe response * [ OCE_PROBE_REQ_HIGH_TX_RATE ]: probe request TX at high rate (at least 5.5Mbps) * [ OCE_PROBE_REQ_DEFERRAL_SUPPRESSION ]: probe request tx deferral and suppression * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211 * [ TXQS ]: FQ-CoDel-enabled intermediate TXQs * [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans * [ EXT_KEY_ID ]: Extended Key ID support * [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support * [ DEL_IBSS_STA ]: deletion of IBSS station support * [ SCAN_FREQ_KHZ ]: scan on kHz frequency support * [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support * [ PROT_RANGE_NEGO_AND_MEASURE ]: support for MFP in range measurement negotiation/procedure * [ POWERED_ADDR_CHANGE ]: can change MAC address while up