/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-60-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Fujitsu MHV Device Model: FUJITSU MHV2080AH Serial Number: -- Firmware Version: 00830096 User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 T13/1410D revision 3a Local Time is: Sat Aug 19 10:00:27 2023 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 434) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 55) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 046 - 30116 2 Throughput_Performance P-S--- 100 100 030 - 24051712 3 Spin_Up_Time PO---- 100 100 025 - 1 4 Start_Stop_Count -O--CK 099 099 000 - 1249 5 Reallocated_Sector_Ct PO--CK 100 100 024 - 3 (1997 3) 7 Seek_Error_Rate POSR-- 100 059 047 - 984 8 Seek_Time_Performance P-S--- 100 100 019 - 0 9 Power_On_Seconds -O--CK 054 054 000 - 23459h+35m+42s 10 Spin_Retry_Count PO--C- 100 100 020 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1211 192 Power-Off_Retract_Count -O--CK 100 100 000 - 65 193 Load_Cycle_Count -O--CK 089 089 000 - 223593 194 Temperature_Celsius -O---K 100 100 000 - 41 (Min/Max 18/54) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 98 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 (12 7005) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 22 200 Multi_Zone_Error_Rate POSR-- 100 079 060 - 21328 203 Run_Out_Cancel -O---- 100 100 000 - 3728069165160 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x09 SL R/W 1 Selective self-test log 0x80-0x9f SL R/W 16 Host vendor specific log 0xa1 SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 22 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 22 occurred at disk power-on lifetime: 7895 hours (328 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 ff 01 00 00 00 e0 00 00:02:39.999 READ DMA c8 ff 01 00 00 00 e0 00 00:02:39.634 READ DMA c8 ff 01 00 00 00 e0 00 00:02:39.148 READ DMA c8 ff 01 00 00 00 e0 00 00:02:38.716 READ DMA c8 ff 01 00 00 00 e0 00 00:02:34.239 READ DMA Error 21 occurred at disk power-on lifetime: 7895 hours (328 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 ff 01 00 00 00 e0 00 00:02:39.634 READ DMA c8 ff 01 00 00 00 e0 00 00:02:39.148 READ DMA c8 ff 01 00 00 00 e0 00 00:02:38.716 READ DMA c8 ff 01 00 00 00 e0 00 00:02:34.239 READ DMA c8 ff 01 00 00 00 e0 00 00:02:33.874 READ DMA Error 20 occurred at disk power-on lifetime: 7895 hours (328 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 ff 01 00 00 00 e0 00 00:02:39.148 READ DMA c8 ff 01 00 00 00 e0 00 00:02:38.716 READ DMA c8 ff 01 00 00 00 e0 00 00:02:34.239 READ DMA c8 ff 01 00 00 00 e0 00 00:02:33.874 READ DMA c8 ff 01 00 00 00 e0 00 00:02:33.509 READ DMA Error 19 occurred at disk power-on lifetime: 7895 hours (328 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 ff 01 00 00 00 e0 00 00:02:38.716 READ DMA c8 ff 01 00 00 00 e0 00 00:02:34.239 READ DMA c8 ff 01 00 00 00 e0 00 00:02:33.874 READ DMA c8 ff 01 00 00 00 e0 00 00:02:33.509 READ DMA c8 ff 01 00 00 00 e0 00 00:02:32.999 READ DMA Error 18 occurred at disk power-on lifetime: 7895 hours (328 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 ff 01 00 00 00 e0 00 00:02:34.239 READ DMA c8 ff 01 00 00 00 e0 00 00:02:33.874 READ DMA c8 ff 01 00 00 00 e0 00 00:02:33.509 READ DMA c8 ff 01 00 00 00 e0 00 00:02:32.999 READ DMA f5 ff 9c 07 00 00 e0 00 00:02:32.932 SECURITY FREEZE LOCK SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 18216 - # 2 Short offline Completed without error 00% 7466 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: --/42 Celsius Lifetime Min/Max Temperature: --/54 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2023-08-19 07:53 42 *********************** 116 2023-08-19 07:54 42 *********************** 117 2023-08-19 07:55 42 *********************** 118 2023-08-19 07:56 43 ************************ 119 2023-08-19 07:57 43 ************************ 120 2023-08-19 07:58 43 ************************ 121 2023-08-19 07:59 ? - 122 2023-08-19 08:00 43 ************************ 123 2023-08-19 08:01 43 ************************ 124 2023-08-19 08:02 43 ************************ 125 2023-08-19 08:03 42 *********************** ... ..( 10 skipped). .. *********************** 8 2023-08-19 08:14 42 *********************** 9 2023-08-19 08:15 43 ************************ 10 2023-08-19 08:16 44 ************************* 11 2023-08-19 08:17 44 ************************* 12 2023-08-19 08:18 43 ************************ ... ..( 3 skipped). .. ************************ 16 2023-08-19 08:22 43 ************************ 17 2023-08-19 08:23 42 *********************** ... ..( 30 skipped). .. *********************** 48 2023-08-19 08:54 42 *********************** 49 2023-08-19 08:55 43 ************************ ... ..( 9 skipped). .. ************************ 59 2023-08-19 09:05 43 ************************ 60 2023-08-19 09:06 ? - 61 2023-08-19 09:07 43 ************************ ... ..( 20 skipped). .. ************************ 82 2023-08-19 09:28 43 ************************ 83 2023-08-19 09:29 42 *********************** 84 2023-08-19 09:30 42 *********************** 85 2023-08-19 09:31 42 *********************** 86 2023-08-19 09:32 41 ********************** ... ..( 6 skipped). .. ********************** 93 2023-08-19 09:39 41 ********************** 94 2023-08-19 09:40 ? - 95 2023-08-19 09:41 41 ********************** 96 2023-08-19 09:42 41 ********************** 97 2023-08-19 09:43 41 ********************** 98 2023-08-19 09:44 ? - 99 2023-08-19 09:45 41 ********************** 100 2023-08-19 09:46 41 ********************** 101 2023-08-19 09:47 41 ********************** 102 2023-08-19 09:48 40 ********************* ... ..( 3 skipped). .. ********************* 106 2023-08-19 09:52 40 ********************* 107 2023-08-19 09:53 41 ********************** 108 2023-08-19 09:54 41 ********************** 109 2023-08-19 09:55 41 ********************** 110 2023-08-19 09:56 40 ********************* 111 2023-08-19 09:57 40 ********************* 112 2023-08-19 09:58 40 ********************* 113 2023-08-19 09:59 ? - 114 2023-08-19 10:00 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-60-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M5 Device Model: SAMSUNG HM160HC Serial Number: -- LU WWN Device Id: 5 0f0000 ... Firmware Version: LQ100-10 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ATA/ATAPI-7 T13/1532D revision 0 Transport Type: Parallel, Unknown (0x00f) Local Time is: Sat Aug 19 10:00:29 2023 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 55) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 55) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 12 3 Spin_Up_Time POS--- 252 252 025 - 2062 4 Start_Stop_Count -O--CK 100 100 000 - 997 5 Reallocated_Sector_Ct PO--CK 005 005 010 NOW 891 7 Seek_Error_Rate -OSR-- 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 071 071 000 - 15145 10 Spin_Retry_Count -O--CK 100 100 051 - 1 12 Power_Cycle_Count -O--CK 100 100 000 - 653 191 G-Sense_Error_Rate -O--CK 002 002 000 - 999999 192 Power-Off_Retract_Count -O--CK 100 100 000 - 317 194 Temperature_Celsius -O---K 118 094 000 - 40 (Min/Max 14/51) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 81 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--C- 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 20 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 2081 201 Soft_Read_Error_Rate -O--CK 252 252 000 - 0 223 Load_Retry_Count -O--CK 100 100 000 - 921 225 Load_Cycle_Count -O--CK 082 082 000 - 184742 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x08 SL R/O 1 Power Conditions log 0x80 GPL,SL R/W 16 Host vendor specific log 0x81-0x9f SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 20 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 20 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:40.875 READ DMA Error 19 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:40.437 READ DMA Error 18 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:40.062 READ DMA Error 17 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:35.437 READ DMA Error 16 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:40.875 READ DMA Error 15 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:40.437 READ DMA Error 14 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:40.062 READ DMA Error 13 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 ff 00 01 00 00 00 00 00 00 e0 00 00:02:35.437 READ DMA SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 10011 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 39/41 Celsius Lifetime Min/Max Temperature: 15/51 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 15/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (13) Index Estimated Time Temperature Celsius 14 2023-08-19 07:53 41 ********************** ... ..( 10 skipped). .. ********************** 25 2023-08-19 08:04 41 ********************** 26 2023-08-19 08:05 39 ******************** 27 2023-08-19 08:06 39 ******************** 28 2023-08-19 08:07 39 ******************** 29 2023-08-19 08:08 ? - 30 2023-08-19 08:09 39 ******************** 31 2023-08-19 08:10 40 ********************* 32 2023-08-19 08:11 40 ********************* 33 2023-08-19 08:12 41 ********************** 34 2023-08-19 08:13 40 ********************* ... ..( 2 skipped). .. ********************* 37 2023-08-19 08:16 40 ********************* 38 2023-08-19 08:17 39 ******************** ... ..( 4 skipped). .. ******************** 43 2023-08-19 08:22 39 ******************** 44 2023-08-19 08:23 40 ********************* 45 2023-08-19 08:24 39 ******************** ... ..( 12 skipped). .. ******************** 58 2023-08-19 08:37 39 ******************** 59 2023-08-19 08:38 41 ********************** ... ..( 8 skipped). .. ********************** 68 2023-08-19 08:47 41 ********************** 69 2023-08-19 08:48 40 ********************* ... ..( 8 skipped). .. ********************* 78 2023-08-19 08:57 40 ********************* 79 2023-08-19 08:58 39 ******************** ... ..( 28 skipped). .. ******************** 108 2023-08-19 09:27 39 ******************** 109 2023-08-19 09:28 40 ********************* ... ..( 8 skipped). .. ********************* 118 2023-08-19 09:37 40 ********************* 119 2023-08-19 09:38 39 ******************** ... ..( 18 skipped). .. ******************** 10 2023-08-19 09:57 39 ******************** 11 2023-08-19 09:58 40 ********************* 12 2023-08-19 09:59 40 ********************* 13 2023-08-19 10:00 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported