/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.17.5-051705-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E680 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GG2OAH10 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 18 06:25:13 2022 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 113) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 077 062 - 0 2 Throughput_Performance P-S--K 100 100 040 - 0 3 Spin_Up_Time PO---K 253 100 033 - 1 4 Start_Stop_Count -O--CK 098 098 000 - 3430 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 100 100 040 - 0 9 Power_On_Hours -O--CK 090 090 000 - 4592 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 3427 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 001 000 - 154670370479852 188 Command_Timeout -O--CK 100 096 000 - 131091 190 Airflow_Temperature_Cel -O---K 067 051 045 - 33 (Min/Max 33/34) 191 G-Sense_Error_Rate -O--CK 060 060 000 - 10464 192 Power-Off_Retract_Count -O--CK 099 099 000 - 15991028 193 Load_Cycle_Count -O--CK 095 095 000 - 54669 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 24354 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 24354 [1] occurred at disk power-on lifetime: 3828 hours (159 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 88 00 00 1d fb 26 98 0d 00 Error: UNC at LBA = 0x1dfb2698 = 502998680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:20.845 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:20.845 READ LOG EXT 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:17.467 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:17.467 READ LOG EXT 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:14.090 READ FPDMA QUEUED Error 24353 [0] occurred at disk power-on lifetime: 3828 hours (159 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 88 00 00 1d fb 26 98 0d 00 Error: UNC at LBA = 0x1dfb2698 = 502998680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:17.467 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:17.467 READ LOG EXT 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:14.090 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:14.089 READ LOG EXT 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:10.712 READ FPDMA QUEUED Error 24352 [3] occurred at disk power-on lifetime: 3828 hours (159 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 88 00 00 1d fb 26 98 0d 00 Error: UNC at LBA = 0x1dfb2698 = 502998680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:14.090 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:14.089 READ LOG EXT 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:10.712 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:10.711 READ LOG EXT 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:07.334 READ FPDMA QUEUED Error 24351 [2] occurred at disk power-on lifetime: 3828 hours (159 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 88 00 00 1d fb 26 98 0d 00 Error: UNC at LBA = 0x1dfb2698 = 502998680 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:10.712 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:10.711 READ LOG EXT 60 00 a0 00 08 00 00 1d fb 26 80 40 00 06:41:07.334 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 06:41:07.333 READ LOG EXT 60 00 a0 00 78 00 00 1d fb 26 80 40 00 06:41:03.945 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4547 - # 2 Short offline Completed without error 00% 2 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 33/34 Celsius Lifetime Min/Max Temperature: 7/49 Celsius Specified Max Operating Temperature: 32 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2022-07-18 04:18 33 ************** ... ..( 12 skipped). .. ************** 15 2022-07-18 04:31 33 ************** 16 2022-07-18 04:32 ? - 17 2022-07-18 04:33 34 *************** ... ..( 10 skipped). .. *************** 28 2022-07-18 04:44 34 *************** 29 2022-07-18 04:45 33 ************** ... ..( 3 skipped). .. ************** 33 2022-07-18 04:49 33 ************** 34 2022-07-18 04:50 34 *************** 35 2022-07-18 04:51 33 ************** ... ..( 25 skipped). .. ************** 61 2022-07-18 05:17 33 ************** 62 2022-07-18 05:18 34 *************** ... ..( 21 skipped). .. *************** 84 2022-07-18 05:40 34 *************** 85 2022-07-18 05:41 33 ************** ... ..( 8 skipped). .. ************** 94 2022-07-18 05:50 33 ************** 95 2022-07-18 05:51 ? - 96 2022-07-18 05:52 33 ************** 97 2022-07-18 05:53 34 *************** 98 2022-07-18 05:54 33 ************** 99 2022-07-18 05:55 34 *************** ... ..( 2 skipped). .. *************** 102 2022-07-18 05:58 34 *************** 103 2022-07-18 05:59 33 ************** 104 2022-07-18 06:00 34 *************** 105 2022-07-18 06:01 34 *************** 106 2022-07-18 06:02 34 *************** 107 2022-07-18 06:03 33 ************** ... ..( 10 skipped). .. ************** 118 2022-07-18 06:14 33 ************** 119 2022-07-18 06:15 34 *************** 120 2022-07-18 06:16 33 ************** 121 2022-07-18 06:17 34 *************** ... ..( 5 skipped). .. *************** 127 2022-07-18 06:23 34 *************** 0 2022-07-18 06:24 33 ************** 1 2022-07-18 06:25 33 ************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS