/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7 Device Model: SAMSUNG HM500JI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AC101C4 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Apr 19 09:52:08 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8160) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 136) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 4 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 090 081 025 - 3050 4 Start_Stop_Count -O--CK 098 098 000 - 2814 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 5423 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 290 12 Power_Cycle_Count -O--CK 099 099 000 - 1886 191 G-Sense_Error_Rate -O---K 100 100 000 - 1132 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 062 051 000 - 38 (Min/Max 5/49) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 27 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 20288 223 Load_Retry_Count -O--CK 100 100 000 - 290 225 Load_Cycle_Count -O--CK 093 093 000 - 72178 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xbb GPL VS 4 Device vendor specific log 0xbc GPL VS 2 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 28 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 28 [3] occurred at disk power-on lifetime: 422 hours (17 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 eb 18 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 04 00 00 00 05 82 21 68 40 08 00:00:00.543 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 05 81 b3 10 40 00 00:00:00.543 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 05 82 19 68 40 00 00:00:00.543 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 05 82 1d 68 40 00 00:00:00.543 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 05 81 af 08 40 00 00:00:00.543 WRITE FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 422 hours (17 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 a3 08 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 01 00 00 00 00 00 01 00 00 00:00:00.511 NOP [Abort queued commands] 61 00 00 04 00 00 00 05 81 af 08 40 00 00:00:00.511 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 05 81 ab 08 40 00 00:00:00.511 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 05 81 a7 08 40 00 00:00:00.511 WRITE FPDMA QUEUED 61 00 10 04 00 00 00 05 81 a3 08 40 00 00:00:00.511 WRITE FPDMA QUEUED Error 26 [1] occurred at disk power-on lifetime: 422 hours (17 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 1b 78 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 28 00 00 0a e5 1b 78 40 00 00:00:00.412 READ FPDMA QUEUED 60 00 00 00 20 00 00 0a e5 1b 58 40 00 00:00:00.412 READ FPDMA QUEUED 60 00 00 00 08 00 00 3a 38 5a 28 40 00 00:00:00.412 READ FPDMA QUEUED 60 00 00 00 08 00 00 3a 38 5c 28 40 00 00:00:00.412 READ FPDMA QUEUED 60 00 00 00 08 00 00 3a 38 5e 28 40 00 00:00:00.412 READ FPDMA QUEUED Error 25 [0] occurred at disk power-on lifetime: 422 hours (17 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 78 10 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 10 00 00 09 3b 78 08 40 00 00:00:00.042 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 05 73 78 10 40 00 00:00:00.042 WRITE FPDMA QUEUED 61 00 82 00 08 00 00 04 d3 ec 20 40 08 00:00:00.042 WRITE FPDMA QUEUED 61 00 10 00 08 00 00 04 d3 78 00 40 08 00:00:00.042 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 04 cf 93 30 40 08 00:00:00.042 WRITE FPDMA QUEUED Error 24 [7] occurred at disk power-on lifetime: 247 hours (10 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 3d 4f 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 15695 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 00 02 3c cf e0 00 00:00:00.105 READ DMA EXT 25 00 00 00 80 00 00 00 02 3c 4f e0 00 00:00:00.105 READ DMA EXT 25 00 00 00 80 00 00 00 02 3b cf e0 00 00:00:00.105 READ DMA EXT 25 00 00 00 80 00 00 00 02 3b 4f e0 00 00:00:00.105 READ DMA EXT 25 00 00 00 80 00 00 00 02 3a cf e0 00 00:00:00.105 READ DMA EXT Error 23 [6] occurred at disk power-on lifetime: 247 hours (10 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 6b 17 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 27415 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 90 6b 0f e0 00 00:00:00.054 READ DMA EXT 25 00 00 00 08 00 00 00 90 6b 07 e0 00 00:00:00.054 READ DMA EXT 25 00 00 00 08 00 00 00 90 6a ff e0 00 00:00:00.054 READ DMA EXT 25 00 00 00 08 00 00 00 90 6a f7 e0 00 00:00:00.054 READ DMA EXT 25 00 00 00 08 00 00 00 90 6a ef e0 00 00:00:00.054 READ DMA EXT Error 22 [5] occurred at disk power-on lifetime: 247 hours (10 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 16 4f 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 5711 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 90 16 47 e0 00 00:00:00.021 READ DMA EXT 25 00 00 00 08 00 00 00 90 16 3f e0 00 00:00:00.021 READ DMA EXT 25 00 00 00 08 00 00 00 90 16 37 e0 00 00:00:00.021 READ DMA EXT 25 00 00 00 08 00 00 00 90 16 2f e0 00 00:00:00.021 READ DMA EXT 25 00 00 00 08 00 00 00 90 16 27 e0 00 00:00:00.021 READ DMA EXT Error 21 [4] occurred at disk power-on lifetime: 247 hours (10 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 9d 6f 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 40303 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 90 9d 67 e0 00 00:00:00.016 READ DMA EXT 25 00 00 00 08 00 00 00 90 9d 5f e0 00 00:00:00.016 READ DMA EXT 25 00 00 00 08 00 00 00 90 9d 57 e0 00 00:00:00.016 READ DMA EXT 25 00 00 00 08 00 00 00 90 9d 4f e0 00 00:00:00.016 READ DMA EXT 25 00 00 00 08 00 00 00 90 9d 47 e0 00 00:00:00.016 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 30/38 Celsius Lifetime Min/Max Temperature: 15/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (22) Index Estimated Time Temperature Celsius 23 2015-04-18 23:15 37 ****************** 24 2015-04-18 23:20 38 ******************* 25 2015-04-18 23:25 38 ******************* 26 2015-04-18 23:30 38 ******************* 27 2015-04-18 23:35 39 ******************** 28 2015-04-18 23:40 39 ******************** 29 2015-04-18 23:45 38 ******************* 30 2015-04-18 23:50 39 ******************** ... ..( 3 skipped). .. ******************** 34 2015-04-19 00:10 39 ******************** 35 2015-04-19 00:15 40 ********************* 36 2015-04-19 00:20 39 ******************** ... ..( 9 skipped). .. ******************** 46 2015-04-19 01:10 39 ******************** 47 2015-04-19 01:15 38 ******************* ... ..( 3 skipped). .. ******************* 51 2015-04-19 01:35 38 ******************* 52 2015-04-19 01:40 39 ******************** 53 2015-04-19 01:45 39 ******************** 54 2015-04-19 01:50 38 ******************* ... ..( 9 skipped). .. ******************* 64 2015-04-19 02:40 38 ******************* 65 2015-04-19 02:45 37 ****************** ... ..( 9 skipped). .. ****************** 75 2015-04-19 03:35 37 ****************** 76 2015-04-19 03:40 38 ******************* ... ..( 20 skipped). .. ******************* 97 2015-04-19 05:25 38 ******************* 98 2015-04-19 05:30 37 ****************** 99 2015-04-19 05:35 38 ******************* 100 2015-04-19 05:40 38 ******************* 101 2015-04-19 05:45 38 ******************* 102 2015-04-19 05:50 37 ****************** 103 2015-04-19 05:55 36 ***************** ... ..( 13 skipped). .. ***************** 117 2015-04-19 07:05 36 ***************** 118 2015-04-19 07:10 37 ****************** 119 2015-04-19 07:15 36 ***************** 120 2015-04-19 07:20 36 ***************** 121 2015-04-19 07:25 37 ****************** ... ..( 6 skipped). .. ****************** 0 2015-04-19 08:00 37 ****************** 1 2015-04-19 08:05 36 ***************** ... ..( 4 skipped). .. ***************** 6 2015-04-19 08:30 36 ***************** 7 2015-04-19 08:35 37 ****************** 8 2015-04-19 08:40 37 ****************** 9 2015-04-19 08:45 38 ******************* 10 2015-04-19 08:50 39 ******************** 11 2015-04-19 08:55 40 ********************* 12 2015-04-19 09:00 30 *********** 13 2015-04-19 09:05 32 ************* 14 2015-04-19 09:10 34 *************** 15 2015-04-19 09:15 34 *************** 16 2015-04-19 09:20 35 **************** 17 2015-04-19 09:25 36 ***************** 18 2015-04-19 09:30 36 ***************** 19 2015-04-19 09:35 37 ****************** 20 2015-04-19 09:40 37 ****************** 21 2015-04-19 09:45 38 ******************* 22 2015-04-19 09:50 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 10 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific