/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-33-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA THNSNF128GCSS Serial Number: -- Firmware Version: FSLAN102 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Apr 13 10:27:54 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 8) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 100 100 050 - 0 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0 8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 5572 10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 12 Power_Cycle_Count -O--C- 100 100 000 - 2207 167 Unknown_Attribute -O---K 100 100 000 - 0 168 Unknown_Attribute -O--C- 100 100 000 - 0 169 Unknown_Attribute PO--C- 100 100 010 - 100 170 Unknown_Attribute PO--C- 100 100 010 - 0 173 Unknown_Attribute -O--C- 195 195 000 - 0 175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0 192 Power-Off_Retract_Count -O--C- 100 100 000 - 1042 194 Temperature_Celsius -O---K 075 053 000 - 25 (Min/Max 10/47) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 3 (0x0003) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 20/25 Celsius Lifetime Min/Max Temperature: 10/47 Celsius Specified Max Operating Temperature: 10 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 04 00 01 01 00 05 05 00 00 00 00 00 00 00 00 01 00 00 e0 1d 32 01 02 02 00 00 00 00 00 05 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/40 Celsius Min/Max Temperature Limit: 0/80 Celsius Temperature History Size (Index): 128 (7) Index Estimated Time Temperature Celsius 8 2025-04-13 08:20 ? - 9 2025-04-13 08:21 21 ** ... ..( 7 skipped). .. ** 17 2025-04-13 08:29 21 ** 18 2025-04-13 08:30 22 *** ... ..( 4 skipped). .. *** 23 2025-04-13 08:35 22 *** 24 2025-04-13 08:36 23 **** ... ..( 11 skipped). .. **** 36 2025-04-13 08:48 23 **** 37 2025-04-13 08:49 24 ***** ... ..( 27 skipped). .. ***** 65 2025-04-13 09:17 24 ***** 66 2025-04-13 09:18 25 ****** ... ..( 68 skipped). .. ****** 7 2025-04-13 10:27 25 ****** SCT Error Recovery Control: Read: 80 (8.0 seconds) Write: 80 (8.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 21474 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC