/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.15.0-desktop-122.124.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint P120 Device Model: SAMSUNG SP2504C Serial Number: -- Firmware Version: VT100-41 User Capacity: 250,058,268,160 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 4a Local Time is: Tue Mar 30 13:48:07 2021 +05 ==> WARNING: May need -F samsung3 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4835) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 80) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 1 3 Spin_Up_Time POS--- 100 100 025 - 5888 4 Start_Stop_Count -O--CK 075 075 000 - 25571 5 Reallocated_Sector_Ct PO--CK 253 253 010 - 0 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 35232 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 253 000 - 0 12 Power_Cycle_Count -O--CK 087 087 000 - 13718 187 Reported_Uncorrect -O--CK 001 001 000 - 1443738 190 Airflow_Temperature_Cel -O---K 136 082 000 - 34 194 Temperature_Celsius -O---K 136 082 000 - 34 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 2000025 196 Reallocated_Event_Count -O--CK 253 253 000 - 0 197 Current_Pending_Sector -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 100 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x06) instead Device Error Count: 1958 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1958 [5] occurred at disk power-on lifetime: 35183 hours (1465 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 06 aa b4 00 e0 00 Error: UNC 8 sectors at LBA = 0x06aab400 = 111850496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 06 aa b4 00 e0 00 00:00:42.750 READ DMA EXT Error 1957 [4] occurred at disk power-on lifetime: 35183 hours (1465 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 06 aa b4 00 e0 00 Error: UNC 8 sectors at LBA = 0x06aab400 = 111850496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 06 aa b4 00 e0 00 00:00:41.000 READ DMA EXT 25 00 00 00 08 00 00 06 aa b4 08 e0 00 00:00:39.313 READ DMA EXT 25 00 00 00 08 00 00 06 aa b3 f8 e0 00 00:00:39.250 READ DMA EXT 25 00 00 00 08 00 00 06 aa b3 f0 e0 00 00:00:39.250 READ DMA EXT 25 00 00 00 08 00 00 06 ac b3 e8 e0 00 00:00:39.250 READ DMA EXT Error 1956 [3] occurred at disk power-on lifetime: 35183 hours (1465 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 06 aa b3 f0 e0 00 Error: UNC 32 sectors at LBA = 0x06aab3f0 = 111850480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 06 aa b3 f0 e0 00 00:00:39.188 READ DMA EXT 25 00 00 00 80 00 00 0b 86 98 e0 e0 00 00:00:37.438 READ DMA EXT 25 00 00 00 80 00 00 0b 86 98 60 e0 00 00:00:37.438 READ DMA EXT 25 00 00 00 80 00 00 0b 86 97 e0 e0 00 00:00:37.375 READ DMA EXT 25 00 00 00 80 00 00 0b 86 97 60 e0 00 00:00:37.375 READ DMA EXT Error 1955 [2] occurred at disk power-on lifetime: 34184 hours (1424 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 63 ed f0 e0 00 Error: UNC 8 sectors at LBA = 0x0063edf0 = 6548976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 63 ed f0 e0 00 02:26:47.375 READ DMA EXT 25 00 00 00 40 00 00 08 e1 75 e0 e0 00 02:26:45.688 READ DMA EXT 25 00 00 00 08 00 00 00 63 ed e8 e0 00 02:26:45.688 READ DMA EXT 25 00 00 00 08 00 00 00 0b b3 d8 e0 00 02:26:45.688 READ DMA EXT 25 00 00 00 40 00 00 08 e1 75 a0 e0 00 02:26:45.625 READ DMA EXT Error 1954 [1] occurred at disk power-on lifetime: 34184 hours (1424 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 00 63 ed e0 e0 00 Error: UNC 32 sectors at LBA = 0x0063ede0 = 6548960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 63 ed e0 e0 00 02:26:45.500 READ DMA EXT 25 00 00 00 40 00 00 08 e1 75 20 e0 00 02:26:43.813 READ DMA EXT 25 00 00 00 08 00 00 00 0b b3 c8 e0 00 02:26:43.813 READ DMA EXT 25 00 00 00 40 00 00 08 f5 d2 c0 e0 00 02:26:43.813 READ DMA EXT 25 00 00 00 40 00 00 08 e1 74 e0 e0 00 02:26:43.750 READ DMA EXT Error 1953 [0] occurred at disk power-on lifetime: 34184 hours (1424 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 63 28 68 e0 00 Error: UNC 8 sectors at LBA = 0x00632868 = 6498408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 63 28 68 e0 00 02:20:53.000 READ DMA EXT 25 00 00 00 08 00 00 00 63 28 60 e0 00 02:20:51.313 READ DMA EXT 25 00 00 00 80 00 00 03 e7 aa 20 e0 00 02:20:51.313 READ DMA EXT Error 1952 [7] occurred at disk power-on lifetime: 34184 hours (1424 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 00 63 28 60 e0 00 Error: UNC 32 sectors at LBA = 0x00632860 = 6498400 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 63 28 60 e0 00 02:20:51.250 READ DMA EXT 25 00 00 00 80 00 00 04 3f ca 88 e0 00 02:20:49.563 READ DMA EXT 25 00 00 00 80 00 00 04 3f ca 08 e0 00 02:20:49.563 READ DMA EXT 35 00 00 00 08 00 00 00 5f 16 f0 e0 00 02:20:49.563 WRITE DMA EXT 25 00 00 00 80 00 00 04 3f c9 88 e0 00 02:20:49.563 READ DMA EXT Error 1951 [6] occurred at disk power-on lifetime: 34184 hours (1424 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 65 24 58 e0 00 Error: UNC 8 sectors at LBA = 0x00652458 = 6628440 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 65 24 58 e0 00 02:20:16.500 READ DMA EXT 25 00 00 00 08 00 00 00 65 24 50 e0 00 02:20:14.813 READ DMA EXT 25 00 00 00 08 00 00 00 65 24 48 e0 00 02:20:14.813 READ DMA EXT 25 00 00 00 08 00 00 00 65 24 40 e0 00 02:20:14.813 READ DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 34531 - # 2 Extended offline Completed: read failure 90% 29515 236584968 # 3 Extended offline Completed: read failure 90% 29493 236584968 # 4 Extended offline Completed: read failure 50% 28022 236584968 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: --/34 Celsius Lifetime Min/Max Temperature: --/52 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 10/55 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (124) Index Estimated Time Temperature Celsius 125 2021-03-30 11:41 39 ******************** 126 2021-03-30 11:42 39 ******************** 127 2021-03-30 11:43 40 ********************* 0 2021-03-30 11:44 40 ********************* 1 2021-03-30 11:45 40 ********************* 2 2021-03-30 11:46 41 ********************** 3 2021-03-30 11:47 41 ********************** 4 2021-03-30 11:48 41 ********************** 5 2021-03-30 11:49 42 *********************** ... ..( 6 skipped). .. *********************** 12 2021-03-30 11:56 42 *********************** 13 2021-03-30 11:57 44 ************************* 14 2021-03-30 11:58 43 ************************ ... ..( 49 skipped). .. ************************ 64 2021-03-30 12:48 43 ************************ 65 2021-03-30 12:49 44 ************************* ... ..( 21 skipped). .. ************************* 87 2021-03-30 13:11 44 ************************* 88 2021-03-30 13:12 43 ************************ 89 2021-03-30 13:13 43 ************************ 90 2021-03-30 13:14 ? - 91 2021-03-30 13:15 21 ** 92 2021-03-30 13:16 22 *** 93 2021-03-30 13:17 23 **** 94 2021-03-30 13:18 24 ***** 95 2021-03-30 13:19 25 ****** 96 2021-03-30 13:20 25 ****** 97 2021-03-30 13:21 26 ******* 98 2021-03-30 13:22 26 ******* 99 2021-03-30 13:23 27 ******** 100 2021-03-30 13:24 27 ******** 101 2021-03-30 13:25 28 ********* 102 2021-03-30 13:26 28 ********* 103 2021-03-30 13:27 29 ********** 104 2021-03-30 13:28 29 ********** 105 2021-03-30 13:29 30 *********** ... ..( 2 skipped). .. *********** 108 2021-03-30 13:32 30 *********** 109 2021-03-30 13:33 31 ************ 110 2021-03-30 13:34 31 ************ 111 2021-03-30 13:35 31 ************ 112 2021-03-30 13:36 32 ************* ... ..( 4 skipped). .. ************* 117 2021-03-30 13:41 32 ************* 118 2021-03-30 13:42 33 ************** ... ..( 4 skipped). .. ************** 123 2021-03-30 13:47 33 ************** 124 2021-03-30 13:48 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x8001 2 0 Vendor specific