/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD3200BPVT-22JJ5T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Nov 23 18:09:09 2019 -11 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 79) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 143 138 021 - 1825 4 Start_Stop_Count -O--CK 085 085 000 - 15723 5 Reallocated_Sector_Ct PO--CK 173 173 140 - 234 7 Seek_Error_Rate -OSR-K 200 189 000 - 0 9 Power_On_Hours -O--CK 095 095 000 - 4346 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2377 191 G-Sense_Error_Rate -O--CK 001 001 000 - 4923 192 Power-Off_Retract_Count -O--CK 200 200 000 - 206 193 Load_Cycle_Count -O--CK 100 100 000 - 301132 194 Temperature_Celsius -O---K 108 090 000 - 35 196 Reallocated_Event_Count -O--CK 161 161 000 - 39 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 8 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 8 [7] occurred at disk power-on lifetime: 3616 hours (150 days + 16 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 53 00 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 00 00 06:26:13.063 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 00 06:26:13.061 IDENTIFY DEVICE e5 00 00 00 00 00 00 00 00 00 00 00 00 06:26:13.061 CHECK POWER MODE ec 00 00 00 00 00 00 00 00 00 00 00 00 06:26:13.057 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 06:26:13.055 IDENTIFY DEVICE Error 7 [6] occurred at disk power-on lifetime: 3616 hours (150 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 ff d0 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 40 00 06:25:45.423 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 66 ae 10 40 00 06:25:45.423 WRITE FPDMA QUEUED 61 00 80 00 08 00 00 02 10 72 d8 40 00 06:25:45.421 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 00 fd cc e0 40 00 06:25:42.354 WRITE FPDMA QUEUED 60 00 08 00 00 00 00 0f 8d 7e 20 40 00 06:25:17.270 READ FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 3616 hours (150 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 ff d0 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 40 00 06:12:57.301 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 66 ae 10 40 00 06:12:57.301 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 0f fa 2c 98 40 00 06:12:57.300 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 02 10 72 d0 40 00 06:12:57.300 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 00 06:12:56.634 FLUSH CACHE EXT Error 5 [4] occurred at disk power-on lifetime: 3616 hours (150 days + 16 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 c2 4f 53 00 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d8 00 00 00 00 00 c2 4f 00 00 00 06:08:34.977 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 00 00 06:08:34.975 IDENTIFY DEVICE e5 00 00 00 00 00 00 00 00 00 00 00 00 06:08:34.975 CHECK POWER MODE ec 00 00 00 00 00 00 00 00 00 00 00 00 06:08:34.971 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 06:08:34.969 IDENTIFY DEVICE Error 4 [3] occurred at disk power-on lifetime: 3616 hours (150 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 ff d0 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 40 00 06:08:07.724 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 66 ae 10 40 00 06:08:07.723 WRITE FPDMA QUEUED 61 00 20 00 00 00 00 05 67 4b f0 40 00 06:08:07.722 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 02 10 73 40 40 00 06:07:49.943 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 02 10 72 d8 40 00 06:07:46.930 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 3615 hours (150 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 ff d0 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 40 00 05:58:18.795 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 66 ae 10 40 00 05:58:18.795 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 00 67 d7 68 40 00 05:58:18.794 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 00 0e 05 a0 40 00 05:58:17.491 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 00 19 01 a0 40 00 05:58:17.490 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 3615 hours (150 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 ff d0 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 40 00 05:43:47.363 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 66 ae 10 40 00 05:43:42.641 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 00 66 ad 80 40 00 05:43:37.643 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 00 05:43:37.355 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 66 ad 90 40 00 05:43:37.355 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 345 hours (14 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 ff d0 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 00:10:27.272 FLUSH CACHE EXT 61 00 08 00 88 00 00 00 66 ad 90 40 00 00:10:27.272 WRITE FPDMA QUEUED 61 00 18 00 80 00 00 00 67 84 f8 40 00 00:10:27.271 WRITE FPDMA QUEUED 61 00 08 00 78 00 00 00 0a fc b0 40 00 00:10:27.270 WRITE FPDMA QUEUED 61 00 08 00 70 00 00 01 7e 18 80 40 00 00:10:27.270 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 29/35 Celsius Lifetime Min/Max Temperature: 0/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (79) Index Estimated Time Temperature Celsius 80 2019-11-23 16:02 35 **************** 81 2019-11-23 16:03 35 **************** 82 2019-11-23 16:04 ? - 83 2019-11-23 16:05 35 **************** ... ..( 2 skipped). .. **************** 86 2019-11-23 16:08 35 **************** 87 2019-11-23 16:09 ? - 88 2019-11-23 16:10 35 **************** 89 2019-11-23 16:11 ? - 90 2019-11-23 16:12 35 **************** ... ..( 4 skipped). .. **************** 95 2019-11-23 16:17 35 **************** 96 2019-11-23 16:18 ? - 97 2019-11-23 16:19 35 **************** ... ..( 6 skipped). .. **************** 104 2019-11-23 16:26 35 **************** 105 2019-11-23 16:27 ? - 106 2019-11-23 16:28 35 **************** 107 2019-11-23 16:29 35 **************** 108 2019-11-23 16:30 ? - 109 2019-11-23 16:31 35 **************** 110 2019-11-23 16:32 35 **************** 111 2019-11-23 16:33 ? - 112 2019-11-23 16:34 36 ***************** 113 2019-11-23 16:35 36 ***************** 114 2019-11-23 16:36 36 ***************** 115 2019-11-23 16:37 ? - 116 2019-11-23 16:38 36 ***************** ... ..( 9 skipped). .. ***************** 126 2019-11-23 16:48 36 ***************** 127 2019-11-23 16:49 ? - 0 2019-11-23 16:50 36 ***************** ... ..( 2 skipped). .. ***************** 3 2019-11-23 16:53 36 ***************** 4 2019-11-23 16:54 ? - 5 2019-11-23 16:55 36 ***************** 6 2019-11-23 16:56 36 ***************** 7 2019-11-23 16:57 36 ***************** 8 2019-11-23 16:58 ? - 9 2019-11-23 16:59 36 ***************** 10 2019-11-23 17:00 ? - 11 2019-11-23 17:01 21 ** 12 2019-11-23 17:02 21 ** 13 2019-11-23 17:03 21 ** 14 2019-11-23 17:04 ? - 15 2019-11-23 17:05 22 *** 16 2019-11-23 17:06 22 *** 17 2019-11-23 17:07 ? - 18 2019-11-23 17:08 22 *** 19 2019-11-23 17:09 23 **** 20 2019-11-23 17:10 23 **** 21 2019-11-23 17:11 24 ***** 22 2019-11-23 17:12 25 ****** 23 2019-11-23 17:13 26 ******* 24 2019-11-23 17:14 26 ******* 25 2019-11-23 17:15 27 ******** 26 2019-11-23 17:16 27 ******** 27 2019-11-23 17:17 27 ******** 28 2019-11-23 17:18 28 ********* 29 2019-11-23 17:19 28 ********* 30 2019-11-23 17:20 29 ********** 31 2019-11-23 17:21 ? - 32 2019-11-23 17:22 29 ********** 33 2019-11-23 17:23 29 ********** 34 2019-11-23 17:24 30 *********** ... ..( 3 skipped). .. *********** 38 2019-11-23 17:28 30 *********** 39 2019-11-23 17:29 31 ************ ... ..( 2 skipped). .. ************ 42 2019-11-23 17:32 31 ************ 43 2019-11-23 17:33 32 ************* ... ..( 2 skipped). .. ************* 46 2019-11-23 17:36 32 ************* 47 2019-11-23 17:37 33 ************** ... ..( 2 skipped). .. ************** 50 2019-11-23 17:40 33 ************** 51 2019-11-23 17:41 ? - 52 2019-11-23 17:42 33 ************** ... ..( 4 skipped). .. ************** 57 2019-11-23 17:47 33 ************** 58 2019-11-23 17:48 ? - 59 2019-11-23 17:49 33 ************** ... ..( 6 skipped). .. ************** 66 2019-11-23 17:56 33 ************** 67 2019-11-23 17:57 34 *************** ... ..( 2 skipped). .. *************** 70 2019-11-23 18:00 34 *************** 71 2019-11-23 18:01 35 **************** ... ..( 7 skipped). .. **************** 79 2019-11-23 18:09 35 **************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2642 Vendor specific