/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.13-arch1-1] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 250GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT01B6Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Sep 7 12:57:33 2021 SAST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 133) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 092 092 000 - 38360 12 Power_Cycle_Count -O--CK 099 099 000 - 129 177 Wear_Leveling_Count PO--C- 037 037 000 - 1333 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 077 045 000 - 23 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 65 241 Total_LBAs_Written -O--CK 099 099 000 - 99375620068 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SCT command executing in background (5) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 17/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 4294967295/4294901760 SMART Status: 0xffff (Reserved) SCT Temperature History Version: 3 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (101) Index Estimated Time Temperature Celsius 102 2021-09-06 15:40 23 **** ... ..( 5 skipped). .. **** 108 2021-09-06 16:40 23 **** 109 2021-09-06 16:50 22 *** ... ..( 3 skipped). .. *** 113 2021-09-06 17:30 22 *** 114 2021-09-06 17:40 23 **** 115 2021-09-06 17:50 22 *** 116 2021-09-06 18:00 22 *** 117 2021-09-06 18:10 22 *** 118 2021-09-06 18:20 23 **** ... ..( 5 skipped). .. **** 124 2021-09-06 19:20 23 **** 125 2021-09-06 19:30 22 *** 126 2021-09-06 19:40 23 **** 127 2021-09-06 19:50 22 *** ... ..( 13 skipped). .. *** 13 2021-09-06 22:10 22 *** 14 2021-09-06 22:20 23 **** 15 2021-09-06 22:30 22 *** ... ..( 3 skipped). .. *** 19 2021-09-06 23:10 22 *** 20 2021-09-06 23:20 24 ***** ... ..( 3 skipped). .. ***** 24 2021-09-07 00:00 24 ***** 25 2021-09-07 00:10 23 **** 26 2021-09-07 00:20 24 ***** 27 2021-09-07 00:30 25 ****** 28 2021-09-07 00:40 23 **** 29 2021-09-07 00:50 23 **** 30 2021-09-07 01:00 24 ***** 31 2021-09-07 01:10 23 **** ... ..( 3 skipped). .. **** 35 2021-09-07 01:50 23 **** 36 2021-09-07 02:00 22 *** ... ..( 3 skipped). .. *** 40 2021-09-07 02:40 22 *** 41 2021-09-07 02:50 23 **** 42 2021-09-07 03:00 22 *** ... ..( 2 skipped). .. *** 45 2021-09-07 03:30 22 *** 46 2021-09-07 03:40 21 ** 47 2021-09-07 03:50 22 *** 48 2021-09-07 04:00 21 ** 49 2021-09-07 04:10 21 ** 50 2021-09-07 04:20 21 ** 51 2021-09-07 04:30 20 * ... ..( 2 skipped). .. * 54 2021-09-07 05:00 20 * 55 2021-09-07 05:10 22 *** 56 2021-09-07 05:20 22 *** 57 2021-09-07 05:30 25 ****** 58 2021-09-07 05:40 23 **** 59 2021-09-07 05:50 23 **** 60 2021-09-07 06:00 22 *** 61 2021-09-07 06:10 22 *** 62 2021-09-07 06:20 21 ** 63 2021-09-07 06:30 21 ** 64 2021-09-07 06:40 21 ** 65 2021-09-07 06:50 20 * ... ..( 3 skipped). .. * 69 2021-09-07 07:30 20 * 70 2021-09-07 07:40 19 - ... ..( 8 skipped). .. - 79 2021-09-07 09:10 19 - 80 2021-09-07 09:20 20 * ... ..( 5 skipped). .. * 86 2021-09-07 10:20 20 * 87 2021-09-07 10:30 21 ** 88 2021-09-07 10:40 22 *** ... ..( 12 skipped). .. *** 101 2021-09-07 12:50 22 *** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 35 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 35 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.13-arch1-1] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD20EFRX-68EUZN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Sep 7 12:57:33 2021 SAST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 266) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 173 171 021 - 4325 4 Start_Stop_Count -O--CK 100 100 000 - 848 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 045 045 000 - 40385 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 848 192 Power-Off_Retract_Count -O--CK 200 200 000 - 93 193 Load_Cycle_Count -O--CK 189 189 000 - 35672 194 Temperature_Celsius -O---K 125 109 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 15/27 Celsius Lifetime Min/Max Temperature: 11/38 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (267) Index Estimated Time Temperature Celsius 268 2021-09-07 05:00 19 - ... ..( 38 skipped). .. - 307 2021-09-07 05:39 19 - 308 2021-09-07 05:40 18 - ... ..(103 skipped). .. - 412 2021-09-07 07:24 18 - 413 2021-09-07 07:25 19 - ... ..( 72 skipped). .. - 8 2021-09-07 08:38 19 - 9 2021-09-07 08:39 20 * ... ..( 6 skipped). .. * 16 2021-09-07 08:46 20 * 17 2021-09-07 08:47 21 ** 18 2021-09-07 08:48 21 ** 19 2021-09-07 08:49 20 * ... ..( 17 skipped). .. * 37 2021-09-07 09:07 20 * 38 2021-09-07 09:08 21 ** ... ..( 80 skipped). .. ** 119 2021-09-07 10:29 21 ** 120 2021-09-07 10:30 22 *** ... ..( 34 skipped). .. *** 155 2021-09-07 11:05 22 *** 156 2021-09-07 11:06 19 - ... ..( 6 skipped). .. - 163 2021-09-07 11:13 19 - 164 2021-09-07 11:14 20 * ... ..( 8 skipped). .. * 173 2021-09-07 11:23 20 * 174 2021-09-07 11:24 21 ** ... ..( 16 skipped). .. ** 191 2021-09-07 11:41 21 ** 192 2021-09-07 11:42 22 *** ... ..( 17 skipped). .. *** 210 2021-09-07 12:00 22 *** 211 2021-09-07 12:01 21 ** ... ..( 10 skipped). .. ** 222 2021-09-07 12:12 21 ** 223 2021-09-07 12:13 20 * ... ..( 26 skipped). .. * 250 2021-09-07 12:40 20 * 251 2021-09-07 12:41 19 - ... ..( 15 skipped). .. - 267 2021-09-07 12:57 19 - SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 36 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 36 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2209257 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.13-arch1-1] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD20EFRX-68EUZN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Sep 7 12:57:33 2021 SAST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (27420) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 277) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 172 169 021 - 4400 4 Start_Stop_Count -O--CK 100 100 000 - 839 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 045 045 000 - 40230 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 839 192 Power-Off_Retract_Count -O--CK 200 200 000 - 92 193 Load_Cycle_Count -O--CK 187 187 000 - 39708 194 Temperature_Celsius -O---K 125 107 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 16/26 Celsius Lifetime Min/Max Temperature: 11/40 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (74) Index Estimated Time Temperature Celsius 75 2021-09-07 05:00 19 - ... ..( 50 skipped). .. - 126 2021-09-07 05:51 19 - 127 2021-09-07 05:52 18 - ... ..( 91 skipped). .. - 219 2021-09-07 07:24 18 - 220 2021-09-07 07:25 19 - ... ..( 76 skipped). .. - 297 2021-09-07 08:42 19 - 298 2021-09-07 08:43 20 * ... ..( 14 skipped). .. * 313 2021-09-07 08:58 20 * 314 2021-09-07 08:59 21 ** ... ..( 84 skipped). .. ** 399 2021-09-07 10:24 21 ** 400 2021-09-07 10:25 22 *** ... ..( 39 skipped). .. *** 440 2021-09-07 11:05 22 *** 441 2021-09-07 11:06 18 - ... ..( 3 skipped). .. - 445 2021-09-07 11:10 18 - 446 2021-09-07 11:11 19 - ... ..( 5 skipped). .. - 452 2021-09-07 11:17 19 - 453 2021-09-07 11:18 20 * ... ..( 4 skipped). .. * 458 2021-09-07 11:23 20 * 459 2021-09-07 11:24 21 ** ... ..( 52 skipped). .. ** 34 2021-09-07 12:17 21 ** 35 2021-09-07 12:18 20 * ... ..( 3 skipped). .. * 39 2021-09-07 12:22 20 * 40 2021-09-07 12:23 21 ** ... ..( 6 skipped). .. ** 47 2021-09-07 12:30 21 ** 48 2021-09-07 12:31 20 * ... ..( 22 skipped). .. * 71 2021-09-07 12:54 20 * 72 2021-09-07 12:55 19 - 73 2021-09-07 12:56 19 - 74 2021-09-07 12:57 19 - SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 35 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 36 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2209253 Vendor specific