/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.8.16-200.fc32.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZNLN256HCHP-000H1 Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT22H0Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: < 1.8 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Nov 3 18:00:22 2020 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2160) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 36) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 002 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 089 089 001 - 6962 11 Unknown_SSD_Attribute -O---K 099 099 001 - 148 12 Power_Cycle_Count -O--CK 097 097 001 - 2682 170 Unused_Rsvd_Blk_Ct_Chip PO--CK 100 100 010 - 683 171 Program_Fail_Count_Chip -O---K 100 100 010 - 0 172 Erase_Fail_Count_Chip -O--CK 100 100 010 - 0 173 Wear_Leveling_Count PO--CK 096 096 005 - 70 174 Unexpect_Power_Loss_Ct -O--CK 099 099 001 - 148 183 Runtime_Bad_Block -O--CK 100 100 001 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 057 029 040 Past 43 196 Reallocated_Event_Count -O--CK 253 253 001 - 0 198 Offline_Uncorrectable ----CK 100 100 001 - 0 199 CRC_Error_Count -O---K 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 3 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb6 GPL,SL VS 127 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SCT command executing in background (5) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 36/43 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 4294967295/4294901760 SMART Status: 0xffff (Reserved) SCT Temperature History Version: 3 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (51) Index Estimated Time Temperature Celsius 52 2020-11-02 20:50 ? - ... ..( 74 skipped). .. - 127 2020-11-03 09:20 ? - 0 2020-11-03 09:30 40 ********************* 1 2020-11-03 09:40 39 ******************** 2 2020-11-03 09:50 41 ********************** 3 2020-11-03 10:00 40 ********************* ... ..( 2 skipped). .. ********************* 6 2020-11-03 10:30 40 ********************* 7 2020-11-03 10:40 41 ********************** 8 2020-11-03 10:50 40 ********************* 9 2020-11-03 11:00 40 ********************* 10 2020-11-03 11:10 41 ********************** ... ..( 4 skipped). .. ********************** 15 2020-11-03 12:00 41 ********************** 16 2020-11-03 12:10 42 *********************** 17 2020-11-03 12:20 42 *********************** 18 2020-11-03 12:30 41 ********************** 19 2020-11-03 12:40 42 *********************** 20 2020-11-03 12:50 41 ********************** 21 2020-11-03 13:00 42 *********************** 22 2020-11-03 13:10 43 ************************ 23 2020-11-03 13:20 42 *********************** 24 2020-11-03 13:30 38 ******************* 25 2020-11-03 13:40 37 ****************** ... ..( 19 skipped). .. ****************** 45 2020-11-03 17:00 37 ****************** 46 2020-11-03 17:10 36 ***************** 47 2020-11-03 17:20 37 ****************** 48 2020-11-03 17:30 36 ***************** 49 2020-11-03 17:40 37 ****************** 50 2020-11-03 17:50 41 ********************** 51 2020-11-03 18:00 42 *********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x018 6 14085441282 --- Logical Sectors Written 0x01 0x028 6 12425977307 --- Logical Sectors Read 0x01 0x1f8 7 0 --C+ Unknown 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 43 --- Current Temperature 0x05 0x020 1 43 --- Highest Temperature 0x05 0x028 1 43 --- Lowest Temperature |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 16278 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.8.16-200.fc32.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: HGST Travelstar 5K1000 Device Model: HGST HTS541010A9E680 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JA0OA710 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Nov 3 18:00:23 2020 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 219) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 062 - 0 2 Throughput_Performance P-S--K 100 100 040 - 0 3 Spin_Up_Time PO---K 176 100 033 - 1 4 Start_Stop_Count -O--CK 097 097 000 - 5202 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 100 100 040 - 0 9 Power_On_Hours -O--CK 085 085 000 - 6664 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 2679 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 096 000 - 8590000151 188 Command_Timeout -O--CK 100 100 000 - 562655526912 190 Airflow_Temperature_Cel -O---K 066 055 045 - 34 (Min/Max 25/38) 191 G-Sense_Error_Rate -O--CK 099 099 000 - 448 192 Power-Off_Retract_Count -O--CK 100 100 000 - 4784201 193 Load_Cycle_Count -O--CK 088 088 000 - 125017 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 23 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 23 [2] occurred at disk power-on lifetime: 3363 hours (140 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 00 00 00 0b aa 62 e0 0b 00 Error: WP at LBA = 0x0baa62e0 = 195715808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 05 08 00 88 00 00 11 25 42 f8 40 00 02:51:26.388 WRITE FPDMA QUEUED 61 06 00 00 80 00 00 11 25 3c f8 40 00 02:51:26.382 WRITE FPDMA QUEUED 61 0a 00 00 78 00 00 11 25 32 f8 40 00 02:51:26.369 WRITE FPDMA QUEUED 61 06 00 00 70 00 00 11 25 2c f8 40 00 02:51:26.362 WRITE FPDMA QUEUED 61 0a 00 00 68 00 00 11 25 22 f8 40 00 02:51:26.351 WRITE FPDMA QUEUED Error 22 [1] occurred at disk power-on lifetime: 3363 hours (140 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 00 00 00 0b 95 b2 e0 0b 00 Error: WP at LBA = 0x0b95b2e0 = 194360032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 0a 00 00 28 00 00 10 fd 78 00 40 00 02:51:07.048 WRITE FPDMA QUEUED 61 06 80 00 20 00 00 10 fd 71 80 40 00 02:51:07.040 WRITE FPDMA QUEUED 61 09 80 00 18 00 00 10 fd 68 00 40 00 02:51:07.027 WRITE FPDMA QUEUED 61 06 00 00 10 00 00 10 fd 62 00 40 00 02:51:07.022 WRITE FPDMA QUEUED 61 0a 00 00 78 00 00 10 fd 58 00 40 00 02:51:07.009 WRITE FPDMA QUEUED Error 21 [0] occurred at disk power-on lifetime: 3337 hours (139 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 10 00 00 07 27 cb 60 07 00 Error: WP at LBA = 0x0727cb60 = 120048480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 0a 00 00 98 00 00 0f f6 08 00 40 00 08:58:34.668 WRITE FPDMA QUEUED 61 06 00 00 90 00 00 0f f6 02 00 40 00 08:58:34.664 WRITE FPDMA QUEUED 61 0a 00 00 88 00 00 0f f5 f8 00 40 00 08:58:34.650 WRITE FPDMA QUEUED 61 06 00 00 00 00 00 0f f5 f2 00 40 00 08:58:34.644 WRITE FPDMA QUEUED 61 0a 00 00 f8 00 00 0f f5 e8 00 40 00 08:58:34.631 WRITE FPDMA QUEUED Error 20 [3] occurred at disk power-on lifetime: 3337 hours (139 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 24 80 09 18 04 00 Error: WP at LBA = 0x24800918 = 612370712 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 05 40 00 90 00 00 0f a0 cd 50 40 00 08:57:35.140 WRITE FPDMA QUEUED 61 05 50 00 c0 00 00 0f a0 c8 00 40 00 08:57:35.134 WRITE FPDMA QUEUED 61 01 c0 00 b8 00 00 0f a0 c6 40 40 00 08:57:35.133 WRITE FPDMA QUEUED 61 06 18 00 b0 00 00 0f a0 c0 28 40 00 08:57:35.125 WRITE FPDMA QUEUED 61 08 28 00 a8 00 00 0f a0 b8 00 40 00 08:57:35.115 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 25/38 Celsius Lifetime Min/Max Temperature: 6/45 Celsius Specified Max Operating Temperature: 29 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (56) Index Estimated Time Temperature Celsius 57 2020-11-03 15:53 32 ************* ... ..( 33 skipped). .. ************* 91 2020-11-03 16:27 32 ************* 92 2020-11-03 16:28 33 ************** 93 2020-11-03 16:29 32 ************* ... ..( 4 skipped). .. ************* 98 2020-11-03 16:34 32 ************* 99 2020-11-03 16:35 33 ************** 100 2020-11-03 16:36 32 ************* 101 2020-11-03 16:37 32 ************* 102 2020-11-03 16:38 32 ************* 103 2020-11-03 16:39 33 ************** 104 2020-11-03 16:40 32 ************* ... ..( 5 skipped). .. ************* 110 2020-11-03 16:46 32 ************* 111 2020-11-03 16:47 33 ************** 112 2020-11-03 16:48 32 ************* ... ..( 9 skipped). .. ************* 122 2020-11-03 16:58 32 ************* 123 2020-11-03 16:59 33 ************** 124 2020-11-03 17:00 32 ************* ... ..( 41 skipped). .. ************* 38 2020-11-03 17:42 32 ************* 39 2020-11-03 17:43 33 ************** 40 2020-11-03 17:44 32 ************* 41 2020-11-03 17:45 33 ************** ... ..( 10 skipped). .. ************** 52 2020-11-03 17:56 33 ************** 53 2020-11-03 17:57 34 *************** 54 2020-11-03 17:58 33 ************** 55 2020-11-03 17:59 33 ************** 56 2020-11-03 18:00 33 ************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 6095 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS