/dev/nvme0n1 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-58-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: PM991 NVMe Samsung 256GB Serial Number: -- Firmware Version: 25304039 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 256,060,514,304 [256 GB] Unallocated NVM Capacity: 0 Controller ID: 5 NVMe Version: 1.3 Number of Namespaces: 1 Namespace 1 Size/Capacity: 256,060,514,304 [256 GB] Namespace 1 Utilization: 12,323,405,824 [12.3 GB] Namespace 1 Formatted LBA Size: 512 Local Time is: Tue Jan 31 21:37:00 2023 PST Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x0e): Cmd_Eff_Lg Ext_Get_Lg Telmtry_Lg Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 81 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 4.83W - - 0 0 0 0 0 0 1 + 3.54W - - 1 1 1 1 0 0 2 + 3.04W - - 2 2 2 2 0 500 3 - 0.0500W - - 3 3 3 3 210 1200 4 - 0.0050W - - 4 4 4 4 1000 9000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 19 Celsius Available Spare: 100% Available Spare Threshold: 50% Percentage Used: 8% Data Units Read: 24,584,832 [12.5 TB] Data Units Written: 38,240,855 [19.5 TB] Host Read Commands: 392,090,650 Host Write Commands: 509,739,108 Controller Busy Time: 4,003 Power Cycles: 908 Power On Hours: 8,720 Unsafe Shutdowns: 325 Media and Data Integrity Errors: 0 Error Information Log Entries: 1,882 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 19 Celsius Error Information (NVMe Log 0x01, 16 of 64 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 1882 0 0x100c 0x4004 - 0 0 - /dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-58-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Samsung SSD 870 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVT01B6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jan 31 21:37:00 2023 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 098 098 010 - 8 9 Power_On_Hours -O--CK 099 099 000 - 2982 12 Power_Cycle_Count -O--CK 099 099 000 - 596 177 Wear_Leveling_Count PO--C- 100 100 000 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 098 098 010 - 8 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 098 098 010 - 8 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 068 058 000 - 32 195 Hardware_ECC_Recovered -O-RC- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 235 Unknown_Attribute -O--C- 099 099 000 - 122 241 Total_LBAs_Written -O--CK 099 099 000 - 477841010 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 23 - # 2 Short offline Aborted by host 90% 23 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 20/40 Celsius Lifetime Min/Max Temperature: 16/42 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (88) Index Estimated Time Temperature Celsius 89 2023-01-31 00:20 21 ** ... ..( 21 skipped). .. ** 111 2023-01-31 04:00 21 ** 112 2023-01-31 04:10 23 **** 113 2023-01-31 04:20 23 **** 114 2023-01-31 04:30 22 *** 115 2023-01-31 04:40 22 *** 116 2023-01-31 04:50 21 ** ... ..( 21 skipped). .. ** 10 2023-01-31 08:30 21 ** 11 2023-01-31 08:40 20 * ... ..( 5 skipped). .. * 17 2023-01-31 09:40 20 * 18 2023-01-31 09:50 21 ** ... ..( 5 skipped). .. ** 24 2023-01-31 10:50 21 ** 25 2023-01-31 11:00 22 *** 26 2023-01-31 11:10 22 *** 27 2023-01-31 11:20 21 ** ... ..( 5 skipped). .. ** 33 2023-01-31 12:20 21 ** 34 2023-01-31 12:30 20 * 35 2023-01-31 12:40 20 * 36 2023-01-31 12:50 22 *** ... ..( 2 skipped). .. *** 39 2023-01-31 13:20 22 *** 40 2023-01-31 13:30 21 ** ... ..( 30 skipped). .. ** 71 2023-01-31 18:40 21 ** 72 2023-01-31 18:50 23 **** 73 2023-01-31 19:00 24 ***** 74 2023-01-31 19:10 ? - 75 2023-01-31 19:20 22 *** 76 2023-01-31 19:30 28 ********* 77 2023-01-31 19:40 27 ******** 78 2023-01-31 19:50 29 ********** 79 2023-01-31 20:00 30 *********** 80 2023-01-31 20:10 31 ************ 81 2023-01-31 20:20 33 ************** 82 2023-01-31 20:30 35 **************** 83 2023-01-31 20:40 32 ************* 84 2023-01-31 20:50 29 ********** 85 2023-01-31 21:00 30 *********** 86 2023-01-31 21:10 32 ************* 87 2023-01-31 21:20 32 ************* 88 2023-01-31 21:30 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 596 --- Lifetime Power-On Resets 0x01 0x010 4 2982 --- Power-on Hours 0x01 0x018 6 477841010 --- Logical Sectors Written 0x01 0x020 6 5394096 --- Number of Write Commands 0x01 0x028 6 249324599 --- Logical Sectors Read 0x01 0x030 6 3481082 --- Number of Read Commands 0x01 0x038 6 3003000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x020 1 42 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1218 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6621 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 19 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC