Probe #1dfdbeebfb of ASRock FM2A88M-HD+ Desktop Computer

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" HDD DT01ACA... Device Model: TOSHIBA DT01ACA050 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS1OA750 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Apr 29 19:34:35 2016 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3862) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 65) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 79 3 Spin_Up_Time POS--- 127 127 024 - 180 (Average 181) 4 Start_Stop_Count -O--C- 100 100 000 - 1335 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 118 118 020 - 33 9 Power_On_Hours -O--C- 100 100 000 - 5843 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1327 192 Power-Off_Retract_Count -O--CK 099 099 000 - 1341 193 Load_Cycle_Count -O--C- 099 099 000 - 1341 194 Temperature_Celsius -O---- 187 187 000 - 32 (Min/Max 16/40) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 622 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 622 [1] occurred at disk power-on lifetime: 3757 hours (156 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 26 00 00 00 01 16 10 00 00 Error: UNC at LBA = 0x00011610 = 71184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 a8 00 60 00 00 0f 06 c9 a8 40 00 00:42:16.609 READ FPDMA QUEUED 60 01 00 00 58 00 00 0f 06 c8 a8 40 00 00:42:16.609 READ FPDMA QUEUED 60 01 00 00 50 00 00 0f 06 c7 a8 40 00 00:42:16.609 READ FPDMA QUEUED 60 01 00 00 30 00 00 0f 06 c6 a8 40 00 00:42:16.609 READ FPDMA QUEUED 60 00 20 00 50 00 00 0f 4b b8 e0 40 00 00:42:16.600 READ FPDMA QUEUED Error 621 [0] occurred at disk power-on lifetime: 3757 hours (156 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 26 00 00 00 01 16 10 00 00 Error: UNC at LBA = 0x00011610 = 71184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 70 00 00 0f 4b b7 c8 40 00 00:42:12.877 READ FPDMA QUEUED 60 00 08 00 68 00 00 0f 4b 66 e8 40 00 00:42:12.870 READ FPDMA QUEUED 60 00 48 00 60 00 00 0f 4b 66 a0 40 00 00:42:12.845 READ FPDMA QUEUED 60 00 08 00 58 00 00 0f 06 71 28 40 00 00:42:12.841 READ FPDMA QUEUED 61 00 08 00 d0 00 00 02 c5 3e e0 40 00 00:42:12.823 WRITE FPDMA QUEUED Error 620 [3] occurred at disk power-on lifetime: 3757 hours (156 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 26 00 00 00 01 16 10 00 00 Error: UNC at LBA = 0x00011610 = 71184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 b8 00 00 0f 06 60 10 40 00 00:42:09.249 READ FPDMA QUEUED 60 01 00 00 a8 00 00 0f 06 5f 10 40 00 00:42:09.249 READ FPDMA QUEUED 60 01 00 00 a0 00 00 0f 06 5e 10 40 00 00:42:09.249 READ FPDMA QUEUED 60 01 00 00 98 00 00 0f 06 5d 10 40 00 00:42:09.249 READ FPDMA QUEUED 60 01 00 00 90 00 00 0f 06 5c 10 40 00 00:42:09.249 READ FPDMA QUEUED Error 619 [2] occurred at disk power-on lifetime: 3757 hours (156 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 26 00 00 00 01 16 10 00 00 Error: UNC at LBA = 0x00011610 = 71184 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 06 00 28 00 00 0e 41 ae d0 40 00 00:42:04.212 READ FPDMA QUEUED 60 00 2c 00 20 00 00 00 01 16 0a 40 00 00:42:04.212 READ FPDMA QUEUED 61 00 08 00 18 00 00 00 02 74 c8 40 00 00:42:04.212 WRITE FPDMA QUEUED 60 01 00 00 10 00 00 09 70 94 90 40 00 00:42:04.212 READ FPDMA QUEUED 60 00 08 00 08 00 00 08 21 5f 38 40 00 00:42:04.212 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 50% 3755 71184 # 2 Short offline Completed: read failure 50% 3755 71184 # 3 Extended offline Completed without error 00% 2856 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 22/32 Celsius Lifetime Min/Max Temperature: 16/40 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (63) Index Estimated Time Temperature Celsius 64 2016-04-29 17:27 32 ************* ... ..(126 skipped). .. ************* 63 2016-04-29 19:34 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Description 1 ===== = = == General Statistics (rev 1) == 1 0x008 4 1327 Lifetime Power-On Resets 1 0x010 4 5843 Power-on Hours 1 0x018 6 14191270412 Logical Sectors Written 1 0x020 6 156901333 Number of Write Commands 1 0x028 6 63866450888 Logical Sectors Read 1 0x030 6 219314162 Number of Read Commands 3 ===== = = == Rotating Media Statistics (rev 1) == 3 0x008 4 5840 Spindle Motor Power-on Hours 3 0x010 4 5840 Head Flying Hours 3 0x018 4 1341 Head Load Events 3 0x020 4 0 Number of Reallocated Logical Sectors 3 0x028 4 650 Read Recovery Attempts 3 0x030 4 2 Number of Mechanical Start Failures 4 ===== = = == General Errors Statistics (rev 1) == 4 0x008 4 610 Number of Reported Uncorrectable Errors 4 0x010 4 9 Resets Between Cmd Acceptance and Completion 5 ===== = = == Temperature Statistics (rev 1) == 5 0x008 1 32 Current Temperature 5 0x010 1 29~ Average Short Term Temperature 5 0x018 1 30~ Average Long Term Temperature 5 0x020 1 40 Highest Temperature 5 0x028 1 16 Lowest Temperature 5 0x030 1 37~ Highest Average Short Term Temperature 5 0x038 1 25~ Lowest Average Short Term Temperature 5 0x040 1 36~ Highest Average Long Term Temperature 5 0x048 1 25~ Lowest Average Long Term Temperature 5 0x050 4 0 Time in Over-Temperature 5 0x058 1 60 Specified Maximum Operating Temperature 5 0x060 4 0 Time in Under-Temperature 5 0x068 1 0 Specified Minimum Operating Temperature 6 ===== = = == Transport Statistics (rev 1) == 6 0x008 4 12265 Number of Hardware Resets 6 0x010 4 6071 Number of ASR Events 6 0x018 4 0 Number of Interface CRC Errors |_ ~ normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS


Hardware for Linux and BSD

GitHub