/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.12.4-desktop-1omv4050] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD502HJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AJ10002 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Sep 28 18:26:37 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 40) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 4620) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 77) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2482 2 Throughput_Performance POS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 083 058 025 - 5449 4 Start_Stop_Count -O--CK 094 094 000 - 6352 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 16153 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6379 183 Runtime_Bad_Block -O--CK 252 252 010 - 0 184 End-to-End_Error PO--CK 252 252 097 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 570 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---- 067 058 040 - 33 (Min/Max 12/42) 191 G-Sense_Error_Rate -O---K 100 100 000 - 1 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 100 100 000 - 6395 194 Temperature_Celsius -O---- 064 058 000 - 33 (Min/Max 12/42) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 2 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 570 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 570 [1] occurred at disk power-on lifetime: 13706 hours (571 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 6c 98 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 00 00 00 03 12 6d 98 40 08 00:00:00.136 READ FPDMA QUEUED 60 00 00 01 00 00 00 03 12 6c 98 40 08 00:00:00.137 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.137 FLUSH CACHE EXT 60 00 00 01 00 00 00 00 a1 a1 08 40 08 00:00:00.137 READ FPDMA QUEUED 60 00 00 00 68 00 00 00 a6 99 b8 40 08 00:00:00.137 READ FPDMA QUEUED Error 569 [0] occurred at disk power-on lifetime: 13637 hours (568 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 fb 40 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 00 00 00 13 97 fb 58 40 08 00:00:06.005 READ FPDMA QUEUED 60 00 00 00 18 00 00 13 97 fb 40 40 08 00:00:06.006 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:06.006 FLUSH CACHE EXT 60 00 00 00 20 00 00 13 97 fb 20 40 08 00:00:06.006 READ FPDMA QUEUED 60 00 00 00 08 00 00 13 81 1a c0 40 08 00:00:06.006 READ FPDMA QUEUED Error 568 [7] occurred at disk power-on lifetime: 8074 hours (336 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 54 40 e0 00 Error: UNC 1 sectors at LBA = 0x00005440 = 21568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.011 READ DMA EXT 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.010 READ DMA EXT 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 f0 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 10 e0 00 00:00:00.008 READ DMA EXT Error 567 [6] occurred at disk power-on lifetime: 8074 hours (336 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 54 40 e0 00 Error: UNC 1 sectors at LBA = 0x00005440 = 21568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.010 READ DMA EXT 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 f0 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 10 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 ee e0 00 00:00:00.008 READ DMA EXT Error 566 [5] occurred at disk power-on lifetime: 8074 hours (336 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 54 40 e0 00 Error: UNC 1 sectors at LBA = 0x00005440 = 21568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 f0 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 10 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 ee e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 60 e0 00 00:00:00.008 READ DMA EXT Error 565 [4] occurred at disk power-on lifetime: 8064 hours (336 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 54 40 e0 00 Error: UNC 1 sectors at LBA = 0x00005440 = 21568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.010 READ DMA EXT 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.009 READ DMA EXT 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 f0 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 10 e0 00 00:00:00.008 READ DMA EXT Error 564 [3] occurred at disk power-on lifetime: 8064 hours (336 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 54 40 e0 00 Error: UNC 1 sectors at LBA = 0x00005440 = 21568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.009 READ DMA EXT 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 f0 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 10 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 ee e0 00 00:00:00.008 READ DMA EXT Error 563 [2] occurred at disk power-on lifetime: 8064 hours (336 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 54 40 e0 00 Error: UNC 1 sectors at LBA = 0x00005440 = 21568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 54 40 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 f0 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 10 e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 02 00 00 00 01 12 ee e0 00 00:00:00.008 READ DMA EXT 25 00 00 00 10 00 00 00 00 08 60 e0 00 00:00:00.008 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 80% 16143 - # 2 Short offline Interrupted (host reset) 30% 15895 - # 3 Short offline Interrupted (host reset) 80% 14086 - # 4 Short offline Interrupted (host reset) 60% 14064 - # 5 Short offline Interrupted (host reset) 80% 13706 - # 6 Short offline Interrupted (host reset) 40% 13652 - # 7 Short offline Completed without error 00% 12717 - # 8 Short offline Interrupted (host reset) 70% 11353 - # 9 Short offline Interrupted (host reset) 90% 11353 - #10 Short offline Interrupted (host reset) 80% 11282 - #11 Short offline Interrupted (host reset) 60% 10547 - #12 Short offline Completed without error 00% 10547 - #13 Short offline Interrupted (host reset) 50% 10166 - #14 Short offline Interrupted (host reset) 80% 9253 - #15 Short offline Interrupted (host reset) 80% 9250 - #16 Extended offline Interrupted (host reset) 90% 1 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Interrupted [80% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 31/32 Celsius Lifetime Min/Max Temperature: 16/62 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (20) Index Estimated Time Temperature Celsius 21 2021-09-28 07:50 34 *************** ... ..( 2 skipped). .. *************** 24 2021-09-28 08:05 34 *************** 25 2021-09-28 08:10 33 ************** 26 2021-09-28 08:15 29 ********** 27 2021-09-28 08:20 30 *********** 28 2021-09-28 08:25 31 ************ 29 2021-09-28 08:30 31 ************ 30 2021-09-28 08:35 32 ************* 31 2021-09-28 08:40 33 ************** 32 2021-09-28 08:45 33 ************** 33 2021-09-28 08:50 34 *************** 34 2021-09-28 08:55 34 *************** 35 2021-09-28 09:00 33 ************** ... ..( 4 skipped). .. ************** 40 2021-09-28 09:25 33 ************** 41 2021-09-28 09:30 32 ************* 42 2021-09-28 09:35 32 ************* 43 2021-09-28 09:40 31 ************ ... ..( 2 skipped). .. ************ 46 2021-09-28 09:55 31 ************ 47 2021-09-28 10:00 32 ************* 48 2021-09-28 10:05 33 ************** 49 2021-09-28 10:10 33 ************** 50 2021-09-28 10:15 34 *************** 51 2021-09-28 10:20 35 **************** 52 2021-09-28 10:25 35 **************** 53 2021-09-28 10:30 34 *************** 54 2021-09-28 10:35 35 **************** 55 2021-09-28 10:40 35 **************** 56 2021-09-28 10:45 35 **************** 57 2021-09-28 10:50 34 *************** 58 2021-09-28 10:55 33 ************** 59 2021-09-28 11:00 33 ************** 60 2021-09-28 11:05 33 ************** 61 2021-09-28 11:10 34 *************** 62 2021-09-28 11:15 34 *************** 63 2021-09-28 11:20 35 **************** ... ..( 2 skipped). .. **************** 66 2021-09-28 11:35 35 **************** 67 2021-09-28 11:40 34 *************** 68 2021-09-28 11:45 33 ************** 69 2021-09-28 11:50 33 ************** 70 2021-09-28 11:55 33 ************** 71 2021-09-28 12:00 34 *************** 72 2021-09-28 12:05 35 **************** 73 2021-09-28 12:10 36 ***************** 74 2021-09-28 12:15 35 **************** 75 2021-09-28 12:20 34 *************** 76 2021-09-28 12:25 34 *************** 77 2021-09-28 12:30 35 **************** ... ..( 2 skipped). .. **************** 80 2021-09-28 12:45 35 **************** 81 2021-09-28 12:50 36 ***************** 82 2021-09-28 12:55 36 ***************** 83 2021-09-28 13:00 36 ***************** 84 2021-09-28 13:05 37 ****************** 85 2021-09-28 13:10 37 ****************** 86 2021-09-28 13:15 30 *********** 87 2021-09-28 13:20 31 ************ 88 2021-09-28 13:25 31 ************ 89 2021-09-28 13:30 31 ************ 90 2021-09-28 13:35 32 ************* 91 2021-09-28 13:40 32 ************* 92 2021-09-28 13:45 33 ************** 93 2021-09-28 13:50 32 ************* ... ..( 2 skipped). .. ************* 96 2021-09-28 14:05 32 ************* 97 2021-09-28 14:10 31 ************ ... ..( 8 skipped). .. ************ 106 2021-09-28 14:55 31 ************ 107 2021-09-28 15:00 30 *********** ... ..( 3 skipped). .. *********** 111 2021-09-28 15:20 30 *********** 112 2021-09-28 15:25 31 ************ 113 2021-09-28 15:30 31 ************ 114 2021-09-28 15:35 31 ************ 115 2021-09-28 15:40 30 *********** ... ..( 4 skipped). .. *********** 120 2021-09-28 16:05 30 *********** 121 2021-09-28 16:10 31 ************ 122 2021-09-28 16:15 27 ******** 123 2021-09-28 16:20 28 ********* 124 2021-09-28 16:25 29 ********** 125 2021-09-28 16:30 29 ********** 126 2021-09-28 16:35 30 *********** ... ..( 2 skipped). .. *********** 1 2021-09-28 16:50 30 *********** 2 2021-09-28 16:55 31 ************ 3 2021-09-28 17:00 31 ************ 4 2021-09-28 17:05 32 ************* 5 2021-09-28 17:10 32 ************* 6 2021-09-28 17:15 33 ************** ... ..( 2 skipped). .. ************** 9 2021-09-28 17:30 33 ************** 10 2021-09-28 17:35 32 ************* 11 2021-09-28 17:40 33 ************** 12 2021-09-28 17:45 32 ************* 13 2021-09-28 17:50 32 ************* 14 2021-09-28 17:55 31 ************ 15 2021-09-28 18:00 31 ************ 16 2021-09-28 18:05 32 ************* 17 2021-09-28 18:10 33 ************** 18 2021-09-28 18:15 31 ************ 19 2021-09-28 18:20 32 ************* 20 2021-09-28 18:25 32 ************* SCT Error Recovery Control: Read: 75 (7.5 seconds) Write: 75 (7.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 10 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific