/dev/sda === START OF INFORMATION SECTION === Model Family: Fujitsu MHW BH Device Model: FUJITSU MHW2080BH Serial Number: -- LU WWN Device Id: 5 00000e ... Firmware Version: 0085001C User Capacity: 80 026 361 856 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 1.5 Gb/s Local Time is: Tue Dec 8 11:41:13 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 324) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 46) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 046 - 216418 2 Throughput_Performance --S--- 100 100 000 - 20578304 3 Spin_Up_Time PO---- 100 100 025 - 1 4 Start_Stop_Count -O--CK 099 099 000 - 2697 5 Reallocated_Sector_Ct PO--CK 100 100 024 - 3 (1997 3) 7 Seek_Error_Rate -OSR-- 100 100 000 - 316 8 Seek_Time_Performance --S--- 100 100 000 - 0 9 Power_On_Hours -O--CK 064 064 000 - 18036 10 Spin_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 2501 191 G-Sense_Error_Rate -O--C- 100 100 000 - 10065 192 Power-Off_Retract_Count -O--CK 100 100 000 - 80 194 Temperature_Celsius -O---K 100 100 000 - 36 (Min/Max 7/58) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 144 196 Reallocated_Event_Count -O--CK 100 100 000 - 3 (23 7011) 197 Current_Pending_Sector -O--C- 100 099 000 - 0 198 Offline_Uncorrectable ----C- 099 099 000 - 3 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -OSR-- 100 100 000 - 17838 201 Soft_Read_Error_Rate ----C- 100 100 000 - 0 203 Run_Out_Cancel -O---- 100 100 000 - 433722555133 225 Load_Cycle_Count -O--CK 096 096 000 - 90237 240 Head_Flying_Hours -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 51 Comprehensive SMART error log 0x03 GPL,SL R/O 64 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 2 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 205 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 205 [204] occurred at disk power-on lifetime: 17704 hours (737 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 8b 00 00 01 e8 db e9 40 00 Error: ICRC, ABRT at LBA = 0x01e8dbe9 = 32037865 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 c0 00 00 01 e8 e1 54 40 00 00:00:06.411 WRITE FPDMA QUEUED 61 01 00 00 b8 00 00 01 e8 e0 54 40 00 00:00:06.411 WRITE FPDMA QUEUED 61 01 00 00 b0 00 00 01 e8 df 54 40 00 00:00:06.411 WRITE FPDMA QUEUED 61 01 00 00 a8 00 00 01 e8 de 54 40 00 00:00:06.411 WRITE FPDMA QUEUED 61 01 00 00 a0 00 00 01 e8 dd 54 40 00 00:00:06.411 WRITE FPDMA QUEUED Error 204 [203] occurred at disk power-on lifetime: 11678 hours (486 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 65 a7 09 66 0c 00 e0 00 Error: UNC 32 sectors at LBA = 0x65a709660c00 = 111768091626496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 65 a7 09 66 0b a0 e0 00 00:54:27.776 READ DMA c8 00 00 00 80 65 a5 f5 65 a6 8a e0 00 00:54:27.775 READ DMA c8 00 00 00 80 65 a5 f7 65 a5 76 e0 00 00:54:27.774 READ DMA c8 00 00 00 80 65 a5 f9 65 a5 78 e0 00 00:54:27.774 READ DMA c8 00 00 00 80 65 a5 fb 65 a5 7a e0 00 00:54:27.773 READ DMA Error 203 [202] occurred at disk power-on lifetime: 9052 hours (377 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 65 a7 09 66 0c 00 e0 00 Error: UNC 32 sectors at LBA = 0x65a709660c00 = 111768091626496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 65 a7 09 66 0b a0 e0 00 16:34:18.042 READ DMA c8 00 00 00 80 65 a5 f5 65 a6 8a e0 00 16:34:18.042 READ DMA c8 00 00 00 80 65 a5 f7 65 a5 76 e0 00 16:34:18.041 READ DMA c8 00 00 00 80 65 a5 f9 65 a5 78 e0 00 16:34:18.040 READ DMA c8 00 00 00 80 65 a5 fb 65 a5 7a e0 00 16:34:18.039 READ DMA Error 202 [201] occurred at disk power-on lifetime: 9033 hours (376 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 65 a7 09 66 0c 00 e0 00 Error: UNC 32 sectors at LBA = 0x65a709660c00 = 111768091626496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 65 a7 09 66 0b a0 e0 00 01:08:13.621 READ DMA c8 00 00 00 80 65 a5 f5 65 a6 8a e0 00 01:08:13.620 READ DMA c8 00 00 00 80 65 a5 f7 65 a5 76 e0 00 01:08:13.619 READ DMA c8 00 00 00 80 65 a5 f9 65 a5 78 e0 00 01:08:13.618 READ DMA c8 00 00 00 80 65 a5 fb 65 a5 7a e0 00 01:08:13.617 READ DMA Error 201 [200] occurred at disk power-on lifetime: 8952 hours (373 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 65 a7 09 66 0c 00 e0 00 Error: UNC 32 sectors at LBA = 0x65a709660c00 = 111768091626496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 65 a7 09 66 0b a0 e0 00 08:29:08.249 READ DMA c8 00 00 00 80 65 a5 f5 65 a6 8a e0 00 08:29:08.248 READ DMA c8 00 00 00 80 65 a5 f7 65 a5 76 e0 00 08:29:08.247 READ DMA c8 00 00 00 80 65 a5 f9 65 a5 78 e0 00 08:29:08.246 READ DMA c8 00 00 00 80 65 a5 fb 65 a5 7a e0 00 08:29:08.246 READ DMA Error 200 [199] occurred at disk power-on lifetime: 8944 hours (372 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 65 a7 09 66 0c 00 e0 00 Error: UNC 32 sectors at LBA = 0x65a709660c00 = 111768091626496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 65 a7 09 66 0b a0 e0 00 00:07:04.975 READ DMA c8 00 00 00 80 65 a5 f5 65 a6 8a e0 00 00:07:04.974 READ DMA c8 00 00 00 80 65 a5 f7 65 a5 76 e0 00 00:07:04.973 READ DMA c8 00 00 00 80 65 a5 f9 65 a5 78 e0 00 00:07:04.972 READ DMA c8 00 00 00 80 65 a5 fb 65 a5 7a e0 00 00:07:04.971 READ DMA Error 199 [198] occurred at disk power-on lifetime: 8929 hours (372 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 65 a7 09 66 0c 00 e0 00 Error: UNC 32 sectors at LBA = 0x65a709660c00 = 111768091626496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 65 a7 09 66 0b a0 e0 00 00:47:43.830 READ DMA c8 00 00 00 80 65 a5 f5 65 a6 8a e0 00 00:47:43.829 READ DMA c8 00 00 00 80 65 a5 f7 65 a5 76 e0 00 00:47:43.826 READ DMA c8 00 00 00 80 65 a5 f9 65 a5 78 e0 00 00:47:43.825 READ DMA c8 00 00 00 80 65 a5 fb 65 a5 7a e0 00 00:47:43.825 READ DMA Error 198 [197] occurred at disk power-on lifetime: 8824 hours (367 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 65 a7 09 66 0c 00 e0 00 Error: UNC 32 sectors at LBA = 0x65a709660c00 = 111768091626496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 65 a7 09 66 0b a0 e0 00 00:03:07.768 READ DMA c8 00 00 00 80 65 a5 f5 65 a6 8a e0 00 00:03:07.767 READ DMA c8 00 00 00 80 65 a5 f7 65 a5 76 e0 00 00:03:07.766 READ DMA c8 00 00 00 80 65 a5 f9 65 a5 78 e0 00 00:03:07.765 READ DMA c8 00 00 00 80 65 a5 fb 65 a5 7a e0 00 00:03:07.765 READ DMA SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 17903 - # 2 Short offline Interrupted (host reset) 80% 9 - # 3 Short offline Completed without error 00% 1 - # 4 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 0 (0x0000) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 36 Celsius Power Cycle Max Temperature: 37 Celsius Lifetime Max Temperature: 58 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (111) Index Estimated Time Temperature Celsius 112 2015-12-08 09:34 38 ******************* ... ..( 22 skipped). .. ******************* 7 2015-12-08 09:57 38 ******************* 8 2015-12-08 09:58 37 ****************** ... ..( 17 skipped). .. ****************** 26 2015-12-08 10:16 37 ****************** 27 2015-12-08 10:17 38 ******************* ... ..( 13 skipped). .. ******************* 41 2015-12-08 10:31 38 ******************* 42 2015-12-08 10:32 39 ******************** 43 2015-12-08 10:33 38 ******************* 44 2015-12-08 10:34 39 ******************** ... ..( 29 skipped). .. ******************** 74 2015-12-08 11:04 39 ******************** 75 2015-12-08 11:05 40 ********************* 76 2015-12-08 11:06 40 ********************* 77 2015-12-08 11:07 40 ********************* 78 2015-12-08 11:08 39 ******************** 79 2015-12-08 11:09 40 ********************* 80 2015-12-08 11:10 39 ******************** 81 2015-12-08 11:11 39 ******************** 82 2015-12-08 11:12 40 ********************* 83 2015-12-08 11:13 39 ******************** ... ..( 4 skipped). .. ******************** 88 2015-12-08 11:18 39 ******************** 89 2015-12-08 11:19 ? - 90 2015-12-08 11:20 28 ********* 91 2015-12-08 11:21 ? - 92 2015-12-08 11:22 25 ****** 93 2015-12-08 11:23 25 ****** 94 2015-12-08 11:24 27 ******** 95 2015-12-08 11:25 ? - 96 2015-12-08 11:26 29 ********** 97 2015-12-08 11:27 29 ********** 98 2015-12-08 11:28 29 ********** 99 2015-12-08 11:29 30 *********** 100 2015-12-08 11:30 31 ************ 101 2015-12-08 11:31 33 ************** 102 2015-12-08 11:32 33 ************** 103 2015-12-08 11:33 34 *************** 104 2015-12-08 11:34 34 *************** 105 2015-12-08 11:35 35 **************** 106 2015-12-08 11:36 35 **************** 107 2015-12-08 11:37 35 **************** 108 2015-12-08 11:38 36 ***************** ... ..( 2 skipped). .. ***************** 111 2015-12-08 11:41 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC