/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD2500BPVT-22ZEST0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 250 059 350 016 bytes [250 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Feb 28 16:56:35 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 86) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 152 132 021 - 1358 4 Start_Stop_Count -O--CK 093 093 000 - 7371 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 089 089 000 - 8665 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3922 191 G-Sense_Error_Rate -O--CK 001 001 000 - 28918 192 Power-Off_Retract_Count -O--CK 200 200 000 - 91 193 Load_Cycle_Count -O--CK 143 143 000 - 171136 194 Temperature_Celsius -O---K 104 096 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1007 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1007 [22] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 0c 45 00 00 00 00 00 00 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 45 00 00 00 00 00 00 e0 00 00:06:25.375 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 e0 00 00:06:25.375 SET FEATURES [Set transfer mode] b0 00 da 00 00 00 00 00 c2 4f 00 e0 00 00:06:25.266 SMART RETURN STATUS ec 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:25.264 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 e0 00 00:06:23.835 SMART ENABLE OPERATIONS Error 1006 [21] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 0c 00 00 00 00 00 00 e0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 0c 00 00 00 00 00 00 e0 00 00:06:25.375 SET FEATURES [Set transfer mode] b0 00 da 00 00 00 00 00 c2 4f 00 e0 00 00:06:25.266 SMART RETURN STATUS ec 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:25.264 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 e0 00 00:06:23.835 SMART ENABLE OPERATIONS ec 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:23.833 IDENTIFY DEVICE Error 1005 [20] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 01 00 00 05 30 c0 60 40 00 Device Fault; Error: ABRT at LBA = 0x0530c060 = 87081056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 58 00 00 02 57 f6 88 40 00 00:06:14.551 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:14.551 READ LOG EXT 61 01 00 00 98 00 00 05 ec 9e 58 40 00 00:06:14.407 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:14.406 READ LOG EXT 61 01 00 00 d8 00 00 05 ec a6 58 40 00 00:06:14.263 WRITE FPDMA QUEUED Error 1004 [19] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 01 00 00 05 30 c0 60 40 00 Device Fault; Error: ABRT at LBA = 0x0530c060 = 87081056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 98 00 00 05 ec 9e 58 40 00 00:06:14.407 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:14.406 READ LOG EXT 61 01 00 00 d8 00 00 05 ec a6 58 40 00 00:06:14.263 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:14.262 READ LOG EXT 61 01 00 00 18 00 00 05 ec 9c 58 40 00 00:06:14.118 WRITE FPDMA QUEUED Error 1003 [18] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 01 00 00 05 30 c0 60 40 00 Device Fault; Error: ABRT at LBA = 0x0530c060 = 87081056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 d8 00 00 05 ec a6 58 40 00 00:06:14.263 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:14.262 READ LOG EXT 61 01 00 00 18 00 00 05 ec 9c 58 40 00 00:06:14.118 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:14.118 READ LOG EXT 61 00 10 00 58 00 00 02 32 aa 48 40 00 00:06:13.974 WRITE FPDMA QUEUED Error 1002 [17] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 01 00 00 05 30 c0 60 40 00 Device Fault; Error: ABRT at LBA = 0x0530c060 = 87081056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 18 00 00 05 ec 9c 58 40 00 00:06:14.118 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:14.118 READ LOG EXT 61 00 10 00 58 00 00 02 32 aa 48 40 00 00:06:13.974 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:13.973 READ LOG EXT 61 00 10 00 98 00 00 02 51 fe 68 40 00 00:06:13.830 WRITE FPDMA QUEUED Error 1001 [16] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 01 00 00 05 30 c0 60 40 00 Device Fault; Error: ABRT at LBA = 0x0530c060 = 87081056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 58 00 00 02 32 aa 48 40 00 00:06:13.974 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:13.973 READ LOG EXT 61 00 10 00 98 00 00 02 51 fe 68 40 00 00:06:13.830 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:13.829 READ LOG EXT 60 00 40 00 d8 00 00 02 31 69 73 40 00 00:06:13.686 READ FPDMA QUEUED Error 1000 [15] occurred at disk power-on lifetime: 6159 hours (256 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 01 00 00 05 30 c0 60 40 00 Device Fault; Error: ABRT at LBA = 0x0530c060 = 87081056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 98 00 00 02 51 fe 68 40 00 00:06:13.830 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:13.829 READ LOG EXT 60 00 40 00 d8 00 00 02 31 69 73 40 00 00:06:13.686 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:06:13.685 READ LOG EXT 61 01 00 00 18 00 00 05 ec a7 58 40 00 00:06:13.541 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 28/39 Celsius Lifetime Min/Max Temperature: 15/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (56) Index Estimated Time Temperature Celsius 57 2016-02-28 14:49 37 ****************** ... ..( 21 skipped). .. ****************** 79 2016-02-28 15:11 37 ****************** 80 2016-02-28 15:12 38 ******************* ... ..( 6 skipped). .. ******************* 87 2016-02-28 15:19 38 ******************* 88 2016-02-28 15:20 37 ****************** ... ..( 2 skipped). .. ****************** 91 2016-02-28 15:23 37 ****************** 92 2016-02-28 15:24 38 ******************* 93 2016-02-28 15:25 37 ****************** ... ..( 9 skipped). .. ****************** 103 2016-02-28 15:35 37 ****************** 104 2016-02-28 15:36 38 ******************* ... ..( 5 skipped). .. ******************* 110 2016-02-28 15:42 38 ******************* 111 2016-02-28 15:43 37 ****************** 112 2016-02-28 15:44 38 ******************* 113 2016-02-28 15:45 37 ****************** 114 2016-02-28 15:46 38 ******************* 115 2016-02-28 15:47 37 ****************** ... ..( 4 skipped). .. ****************** 120 2016-02-28 15:52 37 ****************** 121 2016-02-28 15:53 ? - 122 2016-02-28 15:54 39 ******************** 123 2016-02-28 15:55 39 ******************** 124 2016-02-28 15:56 38 ******************* 125 2016-02-28 15:57 38 ******************* 126 2016-02-28 15:58 ? - 127 2016-02-28 15:59 29 ********** 0 2016-02-28 16:00 29 ********** 1 2016-02-28 16:01 28 ********* 2 2016-02-28 16:02 29 ********** 3 2016-02-28 16:03 30 *********** 4 2016-02-28 16:04 30 *********** 5 2016-02-28 16:05 31 ************ 6 2016-02-28 16:06 31 ************ 7 2016-02-28 16:07 32 ************* 8 2016-02-28 16:08 32 ************* 9 2016-02-28 16:09 33 ************** 10 2016-02-28 16:10 34 *************** 11 2016-02-28 16:11 35 **************** 12 2016-02-28 16:12 35 **************** 13 2016-02-28 16:13 36 ***************** 14 2016-02-28 16:14 36 ***************** 15 2016-02-28 16:15 36 ***************** 16 2016-02-28 16:16 37 ****************** 17 2016-02-28 16:17 37 ****************** 18 2016-02-28 16:18 38 ******************* 19 2016-02-28 16:19 37 ****************** 20 2016-02-28 16:20 37 ****************** 21 2016-02-28 16:21 37 ****************** 22 2016-02-28 16:22 38 ******************* ... ..( 9 skipped). .. ******************* 32 2016-02-28 16:32 38 ******************* 33 2016-02-28 16:33 39 ******************** 34 2016-02-28 16:34 39 ******************** 35 2016-02-28 16:35 38 ******************* 36 2016-02-28 16:36 38 ******************* 37 2016-02-28 16:37 39 ******************** 38 2016-02-28 16:38 38 ******************* 39 2016-02-28 16:39 39 ******************** 40 2016-02-28 16:40 38 ******************* 41 2016-02-28 16:41 39 ******************** 42 2016-02-28 16:42 38 ******************* ... ..( 3 skipped). .. ******************* 46 2016-02-28 16:46 38 ******************* 47 2016-02-28 16:47 39 ******************** 48 2016-02-28 16:48 38 ******************* 49 2016-02-28 16:49 39 ******************** 50 2016-02-28 16:50 39 ******************** 51 2016-02-28 16:51 38 ******************* 52 2016-02-28 16:52 38 ******************* 53 2016-02-28 16:53 39 ******************** ... ..( 2 skipped). .. ******************** 56 2016-02-28 16:56 39 ******************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 3372 Vendor specific