/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD6400BPVT-80HXZT3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 640,135,028,736 bytes [640 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Feb 9 15:38:37 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (16260) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 160) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 179 179 051 - 284056 3 Spin_Up_Time POS--K 181 176 021 - 1950 4 Start_Stop_Count -O--CK 001 001 000 - 120244 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 079 079 000 - 15624 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 7200 191 G-Sense_Error_Rate -O--CK 001 001 000 - 4764 192 Power-Off_Retract_Count -O--CK 200 200 000 - 283 193 Load_Cycle_Count -O--CK 001 001 000 - 1773993 194 Temperature_Celsius -O---K 111 095 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 49 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 21792 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 21792 [15] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: WP at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 b8 00 00 26 c1 47 38 40 08 00:21:14.924 WRITE FPDMA QUEUED 61 00 08 00 b0 00 00 00 c4 ac 30 40 08 00:21:14.923 WRITE FPDMA QUEUED 61 00 08 00 a8 00 00 00 c0 44 20 40 08 00:21:14.923 WRITE FPDMA QUEUED 61 00 08 00 a0 00 00 00 c0 08 08 40 08 00:21:14.923 WRITE FPDMA QUEUED 60 00 08 00 98 00 00 0f be 1a f0 40 08 00:21:14.923 READ FPDMA QUEUED Error 21791 [14] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: UNC at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 0f be 1a f0 40 08 00:21:12.080 READ FPDMA QUEUED 61 00 08 00 00 00 00 01 04 40 c8 40 08 00:21:12.080 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:12.007 FLUSH CACHE EXT b0 00 d1 00 01 00 00 00 c2 4f 00 00 08 00:21:11.994 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:21:11.994 SET FEATURES [Enable SATA feature] Error 21790 [13] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: UNC at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 0f be 1a f0 40 08 00:21:09.121 READ FPDMA QUEUED 61 00 08 00 50 00 00 0f c1 0e 40 40 08 00:21:09.120 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 0f bd 09 08 40 08 00:21:09.120 WRITE FPDMA QUEUED 61 00 08 00 40 00 00 02 fd 28 70 40 08 00:21:09.120 WRITE FPDMA QUEUED 61 00 18 00 38 00 00 01 04 40 b0 40 08 00:21:09.120 WRITE FPDMA QUEUED Error 21789 [12] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: UNC at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e0 00 00 0f be 1a f0 40 08 00:21:06.288 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 08 00:21:06.288 CHECK POWER MODE ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:06.287 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:21:06.287 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:06.287 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 21788 [11] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: UNC at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 98 00 00 0f be 1a f0 40 08 00:21:03.426 READ FPDMA QUEUED 61 00 08 00 90 00 00 01 04 40 a8 40 08 00:21:03.426 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:03.356 FLUSH CACHE EXT 61 00 20 00 08 00 00 01 04 40 88 40 08 00:21:03.355 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:21:03.355 SET FEATURES [Enable SATA feature] Error 21787 [10] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: UNC at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 70 00 00 0f be 1a f0 40 08 00:21:00.537 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:00.537 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:21:00.536 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:00.536 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:21:00.533 IDENTIFY DEVICE Error 21786 [9] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: UNC at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 0f be 1a f0 40 08 00:20:57.711 READ FPDMA QUEUED 61 00 08 00 38 00 00 01 04 40 80 40 08 00:20:57.711 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:20:57.665 FLUSH CACHE EXT 61 00 50 00 a8 00 00 01 04 40 30 40 08 00:20:57.665 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:20:57.664 SET FEATURES [Enable SATA feature] Error 21785 [8] occurred at disk power-on lifetime: 15609 hours (650 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f be 1a f0 40 00 Error: UNC at LBA = 0x0fbe1af0 = 264116976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 0f be 1a f0 40 08 00:20:54.827 READ FPDMA QUEUED 61 00 08 00 00 00 00 00 02 0c 08 40 08 00:20:54.827 WRITE FPDMA QUEUED 61 00 08 00 f0 00 00 00 02 0c 90 40 08 00:20:54.827 WRITE FPDMA QUEUED 61 00 08 00 e8 00 00 00 02 0d a8 40 08 00:20:54.826 WRITE FPDMA QUEUED 61 00 08 00 e0 00 00 00 02 0f 90 40 08 00:20:54.826 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 24/37 Celsius Lifetime Min/Max Temperature: 0/52 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (20) Index Estimated Time Temperature Celsius 21 2018-02-09 13:31 32 ************* 22 2018-02-09 13:32 32 ************* 23 2018-02-09 13:33 33 ************** 24 2018-02-09 13:34 33 ************** 25 2018-02-09 13:35 33 ************** 26 2018-02-09 13:36 34 *************** ... ..( 3 skipped). .. *************** 30 2018-02-09 13:40 34 *************** 31 2018-02-09 13:41 35 **************** ... ..( 12 skipped). .. **************** 44 2018-02-09 13:54 35 **************** 45 2018-02-09 13:55 36 ***************** ... ..( 17 skipped). .. ***************** 63 2018-02-09 14:13 36 ***************** 64 2018-02-09 14:14 37 ****************** ... ..( 47 skipped). .. ****************** 112 2018-02-09 15:02 37 ****************** 113 2018-02-09 15:03 36 ***************** ... ..( 12 skipped). .. ***************** 126 2018-02-09 15:16 36 ***************** 127 2018-02-09 15:17 37 ****************** ... ..( 2 skipped). .. ****************** 2 2018-02-09 15:20 37 ****************** 3 2018-02-09 15:21 36 ***************** ... ..( 16 skipped). .. ***************** 20 2018-02-09 15:38 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 8832 Vendor specific