/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K500.B Device Model: Hitachi HTS545025B9A300 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: PB2OC60F User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Aug 10 17:01:28 2019 +09 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 83) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 109 109 040 - 4368 3 Spin_Up_Time POS--- 208 208 033 - 1 4 Start_Stop_Count -O--C- 097 097 000 - 5515 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 113 113 040 - 35 9 Power_On_Hours -O--C- 018 018 000 - 36218 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 5366 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 213 193 Load_Cycle_Count -O--C- 001 001 000 - 1410460 194 Temperature_Celsius -O---- 157 157 000 - 35 (Min/Max -7/53) 196 Reallocated_Event_Count -O--CK 100 100 000 - 4 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 24 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 24 [3] occurred at disk power-on lifetime: 6931 hours (288 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 84 41 e0 00 Error: IDNF at LBA = 0x1d1c8441 = 488408129 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:13.200 READ SECTOR(S) EXT 25 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:13.100 READ DMA EXT ef 03 03 0c 46 00 ff ff 00 ff ff e0 00 00:01:13.000 SET FEATURES [Set transfer mode] ef ff 03 10 0c 00 ff ff 00 ff ff e0 00 00:01:13.000 SET FEATURES [Set transfer mode] c6 ff ff 50 10 05 e2 2f 00 ff ff e0 00 00:01:13.000 SET MULTIPLE MODE Error 23 [2] occurred at disk power-on lifetime: 6931 hours (288 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 84 41 e0 00 Error: IDNF 1 sectors at LBA = 0x1d1c8441 = 488408129 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:13.100 READ DMA EXT ef 03 03 0c 46 00 ff ff 00 ff ff e0 00 00:01:13.000 SET FEATURES [Set transfer mode] ef ff 03 10 0c 00 ff ff 00 ff ff e0 00 00:01:13.000 SET FEATURES [Set transfer mode] c6 ff ff 50 10 05 e2 2f 00 ff ff e0 00 00:01:13.000 SET MULTIPLE MODE 10 03 ff 3f 50 1c 84 41 05 e2 2f e0 00 00:01:12.900 RECALIBRATE [OBS-4] Error 22 [1] occurred at disk power-on lifetime: 6931 hours (288 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 84 41 e0 00 Error: IDNF at LBA = 0x1d1c8441 = 488408129 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:12.800 READ SECTOR(S) EXT 25 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:12.700 READ DMA EXT 24 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:12.600 READ SECTOR(S) EXT 25 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:12.500 READ DMA EXT ef 03 03 0c 46 00 ff ff 00 ff ff e0 00 00:01:12.300 SET FEATURES [Set transfer mode] Error 21 [0] occurred at disk power-on lifetime: 6931 hours (288 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 84 41 e0 00 Error: IDNF 1 sectors at LBA = 0x1d1c8441 = 488408129 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:12.700 READ DMA EXT 24 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:12.600 READ SECTOR(S) EXT 25 03 03 00 01 00 00 1d 1c 84 41 e0 00 00:01:12.500 READ DMA EXT ef 03 03 0c 46 00 ff ff 00 ff ff e0 00 00:01:12.300 SET FEATURES [Set transfer mode] ef ff 03 10 0c 00 ff ff 00 ff ff e0 00 00:01:12.300 SET FEATURES [Set transfer mode] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 24/39 Celsius Lifetime Min/Max Temperature: -7/53 Celsius Lifetime Average Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 478 (88) Index Estimated Time Temperature Celsius 89 2019-08-10 09:04 36 ***************** ... ..( 2 skipped). .. ***************** 92 2019-08-10 09:07 36 ***************** 93 2019-08-10 09:08 35 **************** ... ..( 4 skipped). .. **************** 98 2019-08-10 09:13 35 **************** 99 2019-08-10 09:14 36 ***************** ... ..( 6 skipped). .. ***************** 106 2019-08-10 09:21 36 ***************** 107 2019-08-10 09:22 37 ****************** 108 2019-08-10 09:23 37 ****************** 109 2019-08-10 09:24 36 ***************** 110 2019-08-10 09:25 36 ***************** 111 2019-08-10 09:26 24 ***** 112 2019-08-10 09:27 25 ****** 113 2019-08-10 09:28 26 ******* 114 2019-08-10 09:29 26 ******* 115 2019-08-10 09:30 26 ******* 116 2019-08-10 09:31 27 ******** 117 2019-08-10 09:32 28 ********* 118 2019-08-10 09:33 28 ********* 119 2019-08-10 09:34 29 ********** 120 2019-08-10 09:35 29 ********** 121 2019-08-10 09:36 29 ********** 122 2019-08-10 09:37 30 *********** 123 2019-08-10 09:38 30 *********** 124 2019-08-10 09:39 31 ************ ... ..( 2 skipped). .. ************ 127 2019-08-10 09:42 31 ************ 128 2019-08-10 09:43 32 ************* ... ..( 2 skipped). .. ************* 131 2019-08-10 09:46 32 ************* 132 2019-08-10 09:47 33 ************** ... ..( 4 skipped). .. ************** 137 2019-08-10 09:52 33 ************** 138 2019-08-10 09:53 34 *************** ... ..( 6 skipped). .. *************** 145 2019-08-10 10:00 34 *************** 146 2019-08-10 10:01 35 **************** ... ..( 10 skipped). .. **************** 157 2019-08-10 10:12 35 **************** 158 2019-08-10 10:13 36 ***************** ... ..( 17 skipped). .. ***************** 176 2019-08-10 10:31 36 ***************** 177 2019-08-10 10:32 37 ****************** ... ..( 8 skipped). .. ****************** 186 2019-08-10 10:41 37 ****************** 187 2019-08-10 10:42 38 ******************* 188 2019-08-10 10:43 38 ******************* 189 2019-08-10 10:44 37 ****************** ... ..( 5 skipped). .. ****************** 195 2019-08-10 10:50 37 ****************** 196 2019-08-10 10:51 36 ***************** 197 2019-08-10 10:52 37 ****************** ... ..( 5 skipped). .. ****************** 203 2019-08-10 10:58 37 ****************** 204 2019-08-10 10:59 36 ***************** 205 2019-08-10 11:00 37 ****************** 206 2019-08-10 11:01 37 ****************** 207 2019-08-10 11:02 36 ***************** ... ..( 13 skipped). .. ***************** 221 2019-08-10 11:16 36 ***************** 222 2019-08-10 11:17 37 ****************** ... ..( 3 skipped). .. ****************** 226 2019-08-10 11:21 37 ****************** 227 2019-08-10 11:22 38 ******************* 228 2019-08-10 11:23 38 ******************* 229 2019-08-10 11:24 37 ****************** 230 2019-08-10 11:25 37 ****************** 231 2019-08-10 11:26 38 ******************* 232 2019-08-10 11:27 38 ******************* 233 2019-08-10 11:28 38 ******************* 234 2019-08-10 11:29 37 ****************** 235 2019-08-10 11:30 38 ******************* ... ..( 2 skipped). .. ******************* 238 2019-08-10 11:33 38 ******************* 239 2019-08-10 11:34 37 ****************** ... ..( 2 skipped). .. ****************** 242 2019-08-10 11:37 37 ****************** 243 2019-08-10 11:38 36 ***************** ... ..( 11 skipped). .. ***************** 255 2019-08-10 11:50 36 ***************** 256 2019-08-10 11:51 35 **************** ... ..( 67 skipped). .. **************** 324 2019-08-10 12:59 35 **************** 325 2019-08-10 13:00 36 ***************** ... ..(124 skipped). .. ***************** 450 2019-08-10 15:05 36 ***************** 451 2019-08-10 15:06 37 ****************** ... ..( 8 skipped). .. ****************** 460 2019-08-10 15:15 37 ****************** 461 2019-08-10 15:16 38 ******************* ... ..( 5 skipped). .. ******************* 467 2019-08-10 15:22 38 ******************* 468 2019-08-10 15:23 39 ******************** ... ..( 3 skipped). .. ******************** 472 2019-08-10 15:27 39 ******************** 473 2019-08-10 15:28 38 ******************* ... ..( 4 skipped). .. ******************* 0 2019-08-10 15:33 38 ******************* 1 2019-08-10 15:34 37 ****************** ... ..( 4 skipped). .. ****************** 6 2019-08-10 15:39 37 ****************** 7 2019-08-10 15:40 36 ***************** ... ..( 19 skipped). .. ***************** 27 2019-08-10 16:00 36 ***************** 28 2019-08-10 16:01 35 **************** ... ..( 59 skipped). .. **************** 88 2019-08-10 17:01 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 37092 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS