/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-67-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SSDPR-CL100-960-G3 Serial Number: -- Firmware Version: S1024A0 User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Mar 26 15:49:46 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 11560 12 Power_Cycle_Count -O--CK 100 100 050 - 316 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute PO--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 15 164 Unknown_Attribute -O--CK 100 100 050 - 245174 165 Unknown_Attribute -O--CK 100 100 050 - 287 166 Unknown_Attribute -O--CK 100 100 050 - 4 167 Unknown_Attribute -O--CK 100 100 050 - 85 168 Unknown_Attribute -O--CK 100 100 050 - 5050 169 Unknown_Attribute -O--CK 100 100 050 - 99 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 55 194 Temperature_Celsius -O---K 100 100 050 - 40 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written ----CK 100 100 050 - 556278 242 Total_LBAs_Read ----CK 100 100 050 - 239789 245 Unknown_Attribute -O--CK 100 100 050 - 700488 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 7 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7 [2] log entry is empty Error 6 [1] log entry is empty Error 5 [0] log entry is empty Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d1 01 01 00 00 4f 00 c2 01 00 08 00:00:00.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] 2f 00 00 01 01 00 00 00 00 00 03 00 08 00:00:00.000 READ LOG EXT 2f 00 00 01 01 00 00 00 00 00 00 00 08 00:00:00.000 READ LOG EXT b0 00 d5 01 01 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART READ LOG b0 00 da 00 00 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART RETURN STATUS SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 316 --- Lifetime Power-On Resets 0x01 0x010 4 11560 --- Power-on Hours 0x01 0x018 6 2096542527 --- Logical Sectors Written 0x01 0x020 6 34421831 --- Number of Write Commands 0x01 0x028 6 2829919180 --- Logical Sectors Read 0x01 0x030 6 7214011 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 17 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-67-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 2.5" HDD MK..65GSX Device Model: TOSHIBA MK3265GSXN Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: GH101M User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Mar 26 15:49:46 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 98) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 1150 4 Start_Stop_Count -O--CK 100 100 000 - 2435 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 444 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 056 056 000 - 17810 10 Spin_Retry_Count PO--CK 148 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 2003 191 G-Sense_Error_Rate -O--CK 100 100 000 - 110 192 Power-Off_Retract_Count -O--CK 100 100 000 - 65 193 Load_Cycle_Count -O--CK 090 090 000 - 106205 194 Temperature_Celsius -O---K 100 100 000 - 35 (Min/Max 6/53) 196 Reallocated_Event_Count -O--CK 100 100 000 - 72 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 9 220 Disk_Shift -O---- 100 100 000 - 60 222 Loaded_Hours -O--CK 085 085 000 - 6203 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 343 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 937 hours (39 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 42 ea af 00 00 77 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x42eaaf000077 = 73575725793399 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 38 42 ea af 00 00 40 e0 00 00:09:13.841 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:09:13.841 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 00:09:13.838 IDENTIFY DEVICE ef 00 03 00 45 42 ea af 00 00 00 a0 00 00:09:13.838 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:09:13.784 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 8 [7] occurred at disk power-on lifetime: 937 hours (39 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 17 00 00 37 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x17000037 = 385876023 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 18 00 00 17 00 00 20 e0 00 00:09:12.029 READ DMA c8 00 00 00 08 00 00 7f 00 00 10 e0 00 00:09:12.029 READ DMA c8 00 00 00 08 00 00 3f 00 00 78 e0 00 00:09:12.029 READ DMA c8 00 00 00 08 00 00 1f 00 00 38 e0 00 00:09:12.029 READ DMA c8 00 00 00 08 00 08 07 00 00 18 e0 00 00:09:12.017 READ DMA Error 7 [6] occurred at disk power-on lifetime: 937 hours (39 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 25 42 e8 0f e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x2542e80f = 625141775 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 25 42 e8 08 e0 00 00:09:10.063 READ DMA EXT 25 00 00 00 08 00 00 25 42 e8 60 e0 00 00:09:10.055 READ DMA EXT 25 00 00 00 08 00 00 25 42 e9 20 e0 00 00:09:10.055 READ DMA EXT 25 00 00 00 08 00 00 25 42 e9 b0 e0 00 00:09:10.046 READ DMA EXT 25 00 00 00 08 00 00 25 42 ea 70 e0 00 00:09:09.975 READ DMA EXT Error 6 [5] occurred at disk power-on lifetime: 937 hours (39 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 25 42 ea 77 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x2542ea77 = 625142391 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 25 42 ea 70 e0 00 00:09:08.173 READ DMA EXT 25 00 00 00 08 00 00 25 42 e9 a8 e0 00 00:09:08.173 READ DMA EXT 25 00 00 00 08 00 00 25 42 ea a8 e0 00 00:09:08.173 READ DMA EXT c8 00 00 00 08 00 00 07 00 00 08 e0 00 00:09:08.173 READ DMA c8 00 00 00 08 42 ea a7 00 00 00 e0 00 00:09:08.146 READ DMA Error 5 [4] occurred at disk power-on lifetime: 936 hours (39 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 66 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000066 = 102 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 ff ff 00 65 00 00 00 00 00 02 e0 00 00:01:14.040 READ DMA EXT 25 ff ff 00 01 00 00 00 00 00 01 e0 00 00:01:14.040 READ DMA EXT c8 03 ff 45 01 00 ff ff 00 00 00 e0 00 00:01:14.008 READ DMA ef ff 03 10 45 00 ff ff 00 ff ff e0 00 00:01:14.007 SET FEATURES [Set transfer mode] c6 10 ff 3f 10 00 ff ff 00 ff ff e0 00 00:01:14.007 SET MULTIPLE MODE Error 4 [3] occurred at disk power-on lifetime: 936 hours (39 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 0a 7a 38 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x0a7a3800 = 175781888 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 ff ff 00 01 00 00 0a 7a 38 00 e0 00 00:01:09.346 READ DMA EXT 25 ff ff 00 01 00 00 09 50 30 00 e0 00 00:01:09.345 READ DMA EXT 25 ff ff 00 01 00 00 09 50 30 00 e0 00 00:01:09.345 READ DMA EXT 25 ff ff 00 01 00 00 09 50 30 00 e0 00 00:01:09.328 READ DMA EXT 25 ff ff 00 01 00 00 00 00 08 00 e0 00 00:01:09.328 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 936 hours (39 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 01 29 47 01 29 7f e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x1294701297f = 1276796545407 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 ff ff 00 38 01 29 47 01 29 48 e0 00 00:00:09.977 READ DMA c8 ff ff 00 08 00 29 7f 01 29 40 e0 00 00:00:09.968 READ DMA c8 ff ff 00 28 00 29 57 00 29 58 e0 00 00:00:09.968 READ DMA c8 ff ff 00 18 00 08 3f 00 29 40 e0 00 00:00:09.960 READ DMA c8 ff ff 00 21 00 08 1e 00 08 1f e0 00 00:00:09.959 READ DMA Error 2 [1] occurred at disk power-on lifetime: 936 hours (39 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 45 01 00 ff ff 00 00 3e e0 00 Error: ICRC, ABRT 17665 sectors at LBA = 0xffff00003e = 1099494850622 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 03 ff 45 3f 00 ff ff 00 00 00 e0 00 00:00:09.448 READ DMA ef ff 03 10 45 00 ff ff 00 ff ff e0 00 00:00:09.448 SET FEATURES [Set transfer mode] c6 10 ff 3f 10 00 ff ff 00 ff ff e0 00 00:00:09.447 SET MULTIPLE MODE 91 03 10 01 3f 00 00 01 00 ff ff ef 00 00:00:09.447 INITIALIZE DEVICE PARAMETERS [OBS-6] ff ff ff ff ff ff ff ff ff ff ff ff 0c 00:00:09.429 [VENDOR SPECIFIC] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 26/39 Celsius Lifetime Min/Max Temperature: 6/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (440) Index Estimated Time Temperature Celsius 441 2023-03-26 07:52 36 ***************** ... ..( 63 skipped). .. ***************** 27 2023-03-26 08:56 36 ***************** 28 2023-03-26 08:57 37 ****************** 29 2023-03-26 08:58 36 ***************** ... ..( 7 skipped). .. ***************** 37 2023-03-26 09:06 36 ***************** 38 2023-03-26 09:07 37 ****************** 39 2023-03-26 09:08 36 ***************** ... ..( 17 skipped). .. ***************** 57 2023-03-26 09:26 36 ***************** 58 2023-03-26 09:27 37 ****************** 59 2023-03-26 09:28 36 ***************** ... ..( 7 skipped). .. ***************** 67 2023-03-26 09:36 36 ***************** 68 2023-03-26 09:37 37 ****************** 69 2023-03-26 09:38 36 ***************** ... ..( 7 skipped). .. ***************** 77 2023-03-26 09:46 36 ***************** 78 2023-03-26 09:47 37 ****************** 79 2023-03-26 09:48 36 ***************** ... ..( 7 skipped). .. ***************** 87 2023-03-26 09:56 36 ***************** 88 2023-03-26 09:57 37 ****************** 89 2023-03-26 09:58 36 ***************** ... ..( 7 skipped). .. ***************** 97 2023-03-26 10:06 36 ***************** 98 2023-03-26 10:07 37 ****************** 99 2023-03-26 10:08 36 ***************** ... ..( 17 skipped). .. ***************** 117 2023-03-26 10:26 36 ***************** 118 2023-03-26 10:27 37 ****************** 119 2023-03-26 10:28 36 ***************** ... ..( 7 skipped). .. ***************** 127 2023-03-26 10:36 36 ***************** 128 2023-03-26 10:37 37 ****************** 129 2023-03-26 10:38 36 ***************** ... ..( 65 skipped). .. ***************** 195 2023-03-26 11:44 36 ***************** 196 2023-03-26 11:45 35 **************** 197 2023-03-26 11:46 35 **************** 198 2023-03-26 11:47 36 ***************** ... ..( 8 skipped). .. ***************** 207 2023-03-26 11:56 36 ***************** 208 2023-03-26 11:57 37 ****************** 209 2023-03-26 11:58 36 ***************** ... ..( 37 skipped). .. ***************** 247 2023-03-26 12:36 36 ***************** 248 2023-03-26 12:37 37 ****************** 249 2023-03-26 12:38 36 ***************** ... ..( 7 skipped). .. ***************** 257 2023-03-26 12:46 36 ***************** 258 2023-03-26 12:47 37 ****************** 259 2023-03-26 12:48 36 ***************** ... ..( 7 skipped). .. ***************** 267 2023-03-26 12:56 36 ***************** 268 2023-03-26 12:57 37 ****************** 269 2023-03-26 12:58 36 ***************** ... ..( 7 skipped). .. ***************** 277 2023-03-26 13:06 36 ***************** 278 2023-03-26 13:07 37 ****************** 279 2023-03-26 13:08 36 ***************** ... ..( 7 skipped). .. ***************** 287 2023-03-26 13:16 36 ***************** 288 2023-03-26 13:17 37 ****************** 289 2023-03-26 13:18 36 ***************** ... ..( 7 skipped). .. ***************** 297 2023-03-26 13:26 36 ***************** 298 2023-03-26 13:27 37 ****************** 299 2023-03-26 13:28 37 ****************** 300 2023-03-26 13:29 36 ***************** ... ..( 27 skipped). .. ***************** 328 2023-03-26 13:57 36 ***************** 329 2023-03-26 13:58 37 ****************** 330 2023-03-26 13:59 36 ***************** ... ..( 16 skipped). .. ***************** 347 2023-03-26 14:16 36 ***************** 348 2023-03-26 14:17 37 ****************** 349 2023-03-26 14:18 36 ***************** ... ..( 17 skipped). .. ***************** 367 2023-03-26 14:36 36 ***************** 368 2023-03-26 14:37 37 ****************** 369 2023-03-26 14:38 37 ****************** 370 2023-03-26 14:39 36 ***************** ... ..( 6 skipped). .. ***************** 377 2023-03-26 14:46 36 ***************** 378 2023-03-26 14:47 37 ****************** 379 2023-03-26 14:48 37 ****************** 380 2023-03-26 14:49 36 ***************** ... ..( 6 skipped). .. ***************** 387 2023-03-26 14:56 36 ***************** 388 2023-03-26 14:57 37 ****************** 389 2023-03-26 14:58 37 ****************** 390 2023-03-26 14:59 36 ***************** ... ..( 6 skipped). .. ***************** 397 2023-03-26 15:06 36 ***************** 398 2023-03-26 15:07 37 ****************** 399 2023-03-26 15:08 37 ****************** 400 2023-03-26 15:09 36 ***************** ... ..( 6 skipped). .. ***************** 407 2023-03-26 15:16 36 ***************** 408 2023-03-26 15:17 37 ****************** 409 2023-03-26 15:18 36 ***************** ... ..( 13 skipped). .. ***************** 423 2023-03-26 15:32 36 ***************** 424 2023-03-26 15:33 35 **************** ... ..( 2 skipped). .. **************** 427 2023-03-26 15:36 35 **************** 428 2023-03-26 15:37 36 ***************** 429 2023-03-26 15:38 36 ***************** 430 2023-03-26 15:39 36 ***************** 431 2023-03-26 15:40 35 **************** 432 2023-03-26 15:41 35 **************** 433 2023-03-26 15:42 36 ***************** 434 2023-03-26 15:43 35 **************** ... ..( 2 skipped). .. **************** 437 2023-03-26 15:46 35 **************** 438 2023-03-26 15:47 36 ***************** 439 2023-03-26 15:48 36 ***************** 440 2023-03-26 15:49 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 40376 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 34 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC