/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9320325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0003SDM1 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Jul 1 01:01:18 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 96) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 111 090 006 - 41230664 3 Spin_Up_Time PO---- 098 098 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4831 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 9 7 Seek_Error_Rate POSR-- 084 060 030 - 306564405 9 Power_On_Hours -O--CK 091 091 000 - 8077 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4781 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 1030 188 Command_Timeout -O--CK 100 098 000 - 1582 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 057 040 045 Past 43 (Min/Max 29/43 #427) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 500 192 Power-Off_Retract_Count -O--CK 100 100 000 - 426 193 Load_Cycle_Count -O--CK 019 019 000 - 163382 194 Temperature_Celsius -O---K 043 060 000 - 43 (0 2 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 059 051 000 - 41230664 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 958 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 958 [17] occurred at disk power-on lifetime: 5542 hours (230 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: UNC at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 02 83 62 c0 40 00 00:46:58.356 READ FPDMA QUEUED 60 00 00 00 c0 00 00 00 68 a1 80 40 00 00:46:58.254 READ FPDMA QUEUED 60 00 00 00 08 00 00 0c a1 8f 60 40 00 00:46:58.243 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 48 10 92 40 00 00:46:58.242 READ FPDMA QUEUED 61 00 00 01 00 00 00 04 2d 7b e0 40 00 00:46:58.241 WRITE FPDMA QUEUED Error 957 [16] occurred at disk power-on lifetime: 5542 hours (230 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: UNC at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 00 48 10 92 40 00 00:46:55.646 READ FPDMA QUEUED 60 00 00 00 08 00 00 0c a1 8f 60 40 00 00:46:55.646 READ FPDMA QUEUED 60 00 00 00 c0 00 00 00 68 a1 80 40 00 00:46:55.645 READ FPDMA QUEUED 60 00 00 00 20 00 00 02 83 62 c0 40 00 00:46:55.644 READ FPDMA QUEUED 61 00 00 00 40 00 00 04 2e 60 e0 40 00 00:46:55.644 WRITE FPDMA QUEUED Error 956 [15] occurred at disk power-on lifetime: 5542 hours (230 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: UNC at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 02 c3 b3 d8 40 00 00:46:50.438 READ FPDMA QUEUED 60 00 00 00 08 00 00 06 cb 9c 28 40 00 00:46:50.437 READ FPDMA QUEUED 60 00 00 00 20 00 00 02 83 62 c0 40 00 00:46:50.437 READ FPDMA QUEUED 60 00 00 00 08 00 00 02 c9 e9 a8 40 00 00:46:50.437 READ FPDMA QUEUED 61 00 00 00 10 00 00 00 d0 78 30 40 00 00:46:50.436 WRITE FPDMA QUEUED Error 955 [14] occurred at disk power-on lifetime: 5542 hours (230 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: WP at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 42 00 00 00 d0 77 e0 40 00 00:46:47.525 WRITE FPDMA QUEUED 61 00 00 00 30 00 00 00 d0 0c 10 40 00 00:46:47.524 WRITE FPDMA QUEUED 61 00 00 00 e0 00 00 00 9a be 18 40 00 00:46:47.519 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 00 6f 6d 00 40 00 00:46:47.515 READ FPDMA QUEUED 61 00 00 00 2f 00 00 00 d0 08 e0 40 00 00:46:47.515 WRITE FPDMA QUEUED Error 954 [13] occurred at disk power-on lifetime: 4236 hours (176 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: UNC at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 02 83 62 c0 40 00 00:23:32.359 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:23:32.343 SET FEATURES [Disable SATA feature] 61 00 00 00 88 00 00 00 67 9c 50 40 00 00:23:32.342 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:23:32.341 SET FEATURES [Enable write cache] 60 00 00 00 08 00 00 01 a2 91 a8 40 00 00:23:32.272 READ FPDMA QUEUED Error 953 [12] occurred at disk power-on lifetime: 4236 hours (176 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: UNC at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 02 83 62 c0 40 00 00:23:29.856 READ FPDMA QUEUED 60 00 00 00 08 00 00 01 a2 91 a8 40 00 00:23:29.856 READ FPDMA QUEUED 60 00 00 00 08 00 00 06 df 34 68 40 00 00:23:29.855 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 a0 00 00:23:29.787 SET FEATURES [Disable SATA feature] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:23:29.721 NOP [Abort queued commands] Error 952 [11] occurred at disk power-on lifetime: 4236 hours (176 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: UNC at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 01 a2 91 a8 40 00 00:23:27.448 READ FPDMA QUEUED 60 00 00 00 40 00 00 02 83 62 c0 40 00 00:23:27.448 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 6f df 40 40 00 00:23:27.447 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:23:27.447 SET FEATURES [Enable write cache] 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:23:27.316 NOP [Abort queued commands] Error 951 [10] occurred at disk power-on lifetime: 4236 hours (176 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 83 62 d5 00 00 Error: UNC at LBA = 0x028362d5 = 42164949 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 01 a2 91 a8 40 00 00:23:24.976 READ FPDMA QUEUED 60 00 00 00 40 00 00 02 83 62 c0 40 00 00:23:24.974 READ FPDMA QUEUED 61 00 00 00 08 00 00 06 cc 4d 00 40 00 00:23:24.974 WRITE FPDMA QUEUED 61 00 00 00 18 00 00 00 66 de e0 40 00 00:23:24.916 WRITE FPDMA QUEUED 60 00 00 00 02 00 00 02 2f c4 18 40 00 00:23:24.913 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Min/Max Temperature: 29/43 Celsius Lifetime Min/Max Temperature: 2/60 Celsius Under/Over Temperature Limit Count: 0/33 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2017-06-30 22:54 46 *************************** ... ..( 11 skipped). .. *************************** 59 2017-06-30 23:06 46 *************************** 60 2017-06-30 23:07 47 **************************** ... ..( 12 skipped). .. **************************** 73 2017-06-30 23:20 47 **************************** 74 2017-06-30 23:21 48 ***************************** 75 2017-06-30 23:22 48 ***************************** 76 2017-06-30 23:23 48 ***************************** 77 2017-06-30 23:24 ? - 78 2017-06-30 23:25 48 ***************************** 79 2017-06-30 23:26 48 ***************************** 80 2017-06-30 23:27 48 ***************************** 81 2017-06-30 23:28 49 ****************************** ... ..( 21 skipped). .. ****************************** 103 2017-06-30 23:50 49 ****************************** 104 2017-06-30 23:51 50 ******************************* ... ..( 7 skipped). .. ******************************* 112 2017-06-30 23:59 50 ******************************* 113 2017-07-01 00:00 51 ******************************** ... ..( 17 skipped). .. ******************************** 3 2017-07-01 00:18 51 ******************************** 4 2017-07-01 00:19 50 ******************************* ... ..( 7 skipped). .. ******************************* 12 2017-07-01 00:27 50 ******************************* 13 2017-07-01 00:28 ? - 14 2017-07-01 00:29 29 ********** 15 2017-07-01 00:30 30 *********** 16 2017-07-01 00:31 31 ************ 17 2017-07-01 00:32 32 ************* 18 2017-07-01 00:33 33 ************** 19 2017-07-01 00:34 33 ************** 20 2017-07-01 00:35 34 *************** 21 2017-07-01 00:36 35 **************** 22 2017-07-01 00:37 36 ***************** 23 2017-07-01 00:38 36 ***************** 24 2017-07-01 00:39 37 ****************** 25 2017-07-01 00:40 37 ****************** 26 2017-07-01 00:41 38 ******************* 27 2017-07-01 00:42 38 ******************* 28 2017-07-01 00:43 39 ******************** 29 2017-07-01 00:44 39 ******************** 30 2017-07-01 00:45 39 ******************** 31 2017-07-01 00:46 40 ********************* ... ..( 2 skipped). .. ********************* 34 2017-07-01 00:49 40 ********************* 35 2017-07-01 00:50 41 ********************** ... ..( 4 skipped). .. ********************** 40 2017-07-01 00:55 41 ********************** 41 2017-07-01 00:56 42 *********************** ... ..( 3 skipped). .. *********************** 45 2017-07-01 01:00 42 *********************** 46 2017-07-01 01:01 43 ************************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS