/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda ES.2 Device Model: ST3500320NS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SN04 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 T13/1410D revision 2 Local Time is: Sat Sep 17 19:39:25 2016 MSK ==> WARNING: There are known problems with these drives, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/207963en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 634) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 120) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 115 087 006 - 89524490 3 Spin_Up_Time PO---- 095 094 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 1007 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 441 7 Seek_Error_Rate POSR-- 066 060 030 - 661902155598 9 Power_On_Hours -O--CK 066 066 000 - 30424 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 957 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 599 188 Command_Timeout -O--CK 100 098 000 - 17180196876 189 High_Fly_Writes -O-RCK 093 093 000 - 7 190 Airflow_Temperature_Cel -O---K 067 045 045 Past 33 (Min/Max 33/36) 194 Temperature_Celsius -O---K 033 055 000 - 33 (0 9 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 031 012 000 - 89524490 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 125 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 589 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 589 [8] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 f2 00 22 d0 e0 00 12d+08:32:39.456 READ DMA EXT 35 00 00 00 08 00 00 f3 00 5b f8 e0 00 12d+08:32:39.406 WRITE DMA EXT 35 00 00 00 08 00 00 f4 00 5b 00 e0 00 12d+08:32:39.405 WRITE DMA EXT 35 00 00 00 10 00 00 9d 00 5d f8 e0 00 12d+08:32:39.405 WRITE DMA EXT 35 00 00 00 07 00 00 5b 00 52 20 e0 00 12d+08:32:39.404 WRITE DMA EXT Error 588 [7] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 f2 00 22 d0 e0 00 12d+08:32:37.687 READ DMA EXT 25 00 00 00 40 00 00 f2 00 22 90 e0 00 12d+08:32:37.678 READ DMA EXT 25 00 00 00 40 00 00 f3 00 22 58 e0 00 12d+08:32:37.671 READ DMA EXT 25 00 00 00 80 00 00 f2 00 22 d8 e0 00 12d+08:32:37.224 READ DMA EXT 35 00 00 00 08 00 00 af 00 00 58 e0 00 12d+08:32:37.181 WRITE DMA EXT Error 587 [6] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 f2 00 22 d0 e0 00 12d+08:32:35.446 READ DMA EXT 35 00 00 00 08 00 02 5f 00 d6 c0 e0 00 12d+08:32:35.300 WRITE DMA EXT 35 00 00 00 08 00 00 ff 00 5f 20 e0 00 12d+08:32:35.299 WRITE DMA EXT 35 00 00 00 01 00 02 5f 00 d6 c8 e0 00 12d+08:32:35.299 WRITE DMA EXT 35 00 00 00 08 00 01 8d 00 70 00 e0 00 12d+08:32:35.298 WRITE DMA EXT Error 586 [5] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 f2 00 22 c8 e0 00 12d+08:32:33.514 READ DMA EXT 35 00 00 00 08 00 00 f3 00 5b f0 e0 00 12d+08:32:33.467 WRITE DMA EXT 35 00 00 00 08 00 00 f4 00 5b 00 e0 00 12d+08:32:33.466 WRITE DMA EXT 35 00 00 00 08 00 00 9d 00 5d f0 e0 00 12d+08:32:33.466 WRITE DMA EXT 35 00 00 00 08 00 00 9d 00 5d e8 e0 00 12d+08:32:33.465 WRITE DMA EXT Error 585 [4] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 f2 00 22 c0 e0 00 12d+08:32:31.549 READ DMA EXT 25 00 00 00 80 00 00 f2 00 22 b8 e0 00 12d+08:32:29.674 READ DMA EXT 35 00 00 00 08 00 02 c9 00 4f 18 e0 00 12d+08:32:29.626 WRITE DMA EXT 35 00 00 00 08 00 02 c4 00 4f 78 e0 00 12d+08:32:29.626 WRITE DMA EXT 35 00 00 00 08 00 00 b6 00 62 68 e0 00 12d+08:32:29.625 WRITE DMA EXT Error 584 [3] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 f2 00 22 b8 e0 00 12d+08:32:29.674 READ DMA EXT 35 00 00 00 08 00 02 c9 00 4f 18 e0 00 12d+08:32:29.626 WRITE DMA EXT 35 00 00 00 08 00 02 c4 00 4f 78 e0 00 12d+08:32:29.626 WRITE DMA EXT 35 00 00 00 08 00 00 b6 00 62 68 e0 00 12d+08:32:29.625 WRITE DMA EXT 35 00 00 00 10 00 00 46 00 62 a0 e0 00 12d+08:32:29.625 WRITE DMA EXT Error 583 [2] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 f2 00 22 b0 e0 00 12d+08:32:27.800 READ DMA EXT 35 00 00 00 08 00 00 49 00 62 90 e0 00 12d+08:32:27.751 WRITE DMA EXT 25 00 00 00 80 00 00 f2 00 22 a8 e0 00 12d+08:32:25.902 READ DMA EXT 25 00 00 00 80 00 00 f2 00 22 a0 e0 00 12d+08:32:23.403 READ DMA EXT 25 00 00 00 80 00 00 f2 00 22 98 e0 00 12d+08:32:21.586 READ DMA EXT Error 582 [1] occurred at disk power-on lifetime: 26293 hours (1095 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 f2 00 22 d6 00 00 Error: UNC at LBA = 0xf20022d6 = 4060095190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 f2 00 22 a8 e0 00 12d+08:32:25.902 READ DMA EXT 25 00 00 00 80 00 00 f2 00 22 a0 e0 00 12d+08:32:23.403 READ DMA EXT 25 00 00 00 80 00 00 f2 00 22 98 e0 00 12d+08:32:21.586 READ DMA EXT 35 00 00 00 08 00 00 f3 00 5b f8 e0 00 12d+08:32:21.556 WRITE DMA EXT 35 00 00 00 08 00 00 f4 00 5b 08 e0 00 12d+08:32:21.556 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 28925 - # 2 Short offline Completed without error 00% 28807 - # 3 Short offline Completed without error 00% 28727 - # 4 Extended offline Completed without error 00% 28221 - # 5 Conveyance offline Completed without error 00% 27828 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 33/36 Celsius Lifetime Min/Max Temperature: 9/55 Celsius Under/Over Temperature Limit Count: 0/386 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (105) Index Estimated Time Temperature Celsius 106 2016-09-17 17:32 35 **************** ... ..( 27 skipped). .. **************** 6 2016-09-17 18:00 35 **************** 7 2016-09-17 18:01 36 ***************** 8 2016-09-17 18:02 36 ***************** 9 2016-09-17 18:03 36 ***************** 10 2016-09-17 18:04 35 **************** ... ..( 14 skipped). .. **************** 25 2016-09-17 18:19 35 **************** 26 2016-09-17 18:20 34 *************** ... ..( 48 skipped). .. *************** 75 2016-09-17 19:09 34 *************** 76 2016-09-17 19:10 33 ************** ... ..( 28 skipped). .. ************** 105 2016-09-17 19:39 33 ************** SCT Error Recovery Control: Read: 60 (6,0 seconds) Write: 60 (6,0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 38 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD5000AADS-00S9B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.00A01 User Capacity: 500 106 780 160 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Sep 17 19:39:25 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10380) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 122) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 25 3 Spin_Up_Time POS--K 157 146 021 - 3125 4 Start_Stop_Count -O--CK 096 096 000 - 4750 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 078 078 000 - 16355 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4170 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1497 193 Load_Cycle_Count -O--CK 089 089 000 - 334211 194 Temperature_Celsius -O---K 111 088 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 4 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Invalid Error Log index = 0x0000 (reserved = 0x00) SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 12563 - # 2 Short offline Completed without error 00% 7054 - # 3 Short offline Completed without error 00% 6306 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 32/37 Celsius Lifetime Min/Max Temperature: 32/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (410) Index Estimated Time Temperature Celsius 411 2016-09-17 11:42 36 ***************** ... ..( 13 skipped). .. ***************** 425 2016-09-17 11:56 36 ***************** 426 2016-09-17 11:57 35 **************** ... ..( 3 skipped). .. **************** 430 2016-09-17 12:01 35 **************** 431 2016-09-17 12:02 34 *************** ... ..( 10 skipped). .. *************** 442 2016-09-17 12:13 34 *************** 443 2016-09-17 12:14 35 **************** 444 2016-09-17 12:15 34 *************** 445 2016-09-17 12:16 35 **************** 446 2016-09-17 12:17 34 *************** ... ..( 12 skipped). .. *************** 459 2016-09-17 12:30 34 *************** 460 2016-09-17 12:31 35 **************** 461 2016-09-17 12:32 34 *************** 462 2016-09-17 12:33 35 **************** ... ..( 3 skipped). .. **************** 466 2016-09-17 12:37 35 **************** 467 2016-09-17 12:38 34 *************** 468 2016-09-17 12:39 35 **************** ... ..( 2 skipped). .. **************** 471 2016-09-17 12:42 35 **************** 472 2016-09-17 12:43 34 *************** 473 2016-09-17 12:44 35 **************** 474 2016-09-17 12:45 34 *************** 475 2016-09-17 12:46 35 **************** ... ..( 21 skipped). .. **************** 19 2016-09-17 13:08 35 **************** 20 2016-09-17 13:09 36 ***************** ... ..( 79 skipped). .. ***************** 100 2016-09-17 14:29 36 ***************** 101 2016-09-17 14:30 35 **************** 102 2016-09-17 14:31 36 ***************** ... ..( 7 skipped). .. ***************** 110 2016-09-17 14:39 36 ***************** 111 2016-09-17 14:40 35 **************** ... ..( 2 skipped). .. **************** 114 2016-09-17 14:43 35 **************** 115 2016-09-17 14:44 34 *************** ... ..( 3 skipped). .. *************** 119 2016-09-17 14:48 34 *************** 120 2016-09-17 14:49 33 ************** ... ..( 51 skipped). .. ************** 172 2016-09-17 15:41 33 ************** 173 2016-09-17 15:42 32 ************* ... ..( 2 skipped). .. ************* 176 2016-09-17 15:45 32 ************* 177 2016-09-17 15:46 33 ************** 178 2016-09-17 15:47 33 ************** 179 2016-09-17 15:48 32 ************* ... ..( 24 skipped). .. ************* 204 2016-09-17 16:13 32 ************* 205 2016-09-17 16:14 35 **************** ... ..( 79 skipped). .. **************** 285 2016-09-17 17:34 35 **************** 286 2016-09-17 17:35 34 *************** ... ..( 2 skipped). .. *************** 289 2016-09-17 17:38 34 *************** 290 2016-09-17 17:39 33 ************** ... ..( 8 skipped). .. ************** 299 2016-09-17 17:48 33 ************** 300 2016-09-17 17:49 ? - 301 2016-09-17 17:50 35 **************** 302 2016-09-17 17:51 ? - 303 2016-09-17 17:52 34 *************** 304 2016-09-17 17:53 ? - 305 2016-09-17 17:54 35 **************** ... ..( 5 skipped). .. **************** 311 2016-09-17 18:00 35 **************** 312 2016-09-17 18:01 36 ***************** ... ..( 82 skipped). .. ***************** 395 2016-09-17 19:24 36 ***************** 396 2016-09-17 19:25 37 ****************** 397 2016-09-17 19:26 36 ***************** ... ..( 3 skipped). .. ***************** 401 2016-09-17 19:30 36 ***************** 402 2016-09-17 19:31 37 ****************** 403 2016-09-17 19:32 36 ***************** ... ..( 6 skipped). .. ***************** 410 2016-09-17 19:39 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 23103 Vendor specific /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD30EZRX-00D8PB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3 000 592 982 016 bytes [3,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Sep 17 19:39:26 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 411) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 196 168 021 - 5166 4 Start_Stop_Count -O--CK 099 099 000 - 1952 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 090 090 000 - 7827 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1951 192 Power-Off_Retract_Count -O--CK 200 200 000 - 714 193 Load_Cycle_Count -O--CK 121 121 000 - 238263 194 Temperature_Celsius -O---K 118 103 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5563 - # 2 Short offline Completed without error 00% 4467 - # 3 Conveyance offline Completed without error 00% 3494 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 32/36 Celsius Lifetime Min/Max Temperature: 2/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (466) Index Estimated Time Temperature Celsius 467 2016-09-17 11:42 34 *************** ... ..( 53 skipped). .. *************** 43 2016-09-17 12:36 34 *************** 44 2016-09-17 12:37 35 **************** ... ..( 68 skipped). .. **************** 113 2016-09-17 13:46 35 **************** 114 2016-09-17 13:47 36 ***************** 115 2016-09-17 13:48 35 **************** ... ..(116 skipped). .. **************** 232 2016-09-17 15:45 35 **************** 233 2016-09-17 15:46 34 *************** ... ..( 51 skipped). .. *************** 285 2016-09-17 16:38 34 *************** 286 2016-09-17 16:39 33 ************** ... ..( 49 skipped). .. ************** 336 2016-09-17 17:29 33 ************** 337 2016-09-17 17:30 32 ************* 338 2016-09-17 17:31 32 ************* 339 2016-09-17 17:32 35 **************** ... ..( 34 skipped). .. **************** 374 2016-09-17 18:07 35 **************** 375 2016-09-17 18:08 36 ***************** 376 2016-09-17 18:09 36 ***************** 377 2016-09-17 18:10 36 ***************** 378 2016-09-17 18:11 35 **************** ... ..( 5 skipped). .. **************** 384 2016-09-17 18:17 35 **************** 385 2016-09-17 18:18 36 ***************** ... ..( 2 skipped). .. ***************** 388 2016-09-17 18:21 36 ***************** 389 2016-09-17 18:22 35 **************** 390 2016-09-17 18:23 36 ***************** ... ..( 4 skipped). .. ***************** 395 2016-09-17 18:28 36 ***************** 396 2016-09-17 18:29 35 **************** 397 2016-09-17 18:30 35 **************** 398 2016-09-17 18:31 35 **************** 399 2016-09-17 18:32 36 ***************** ... ..( 4 skipped). .. ***************** 404 2016-09-17 18:37 36 ***************** 405 2016-09-17 18:38 35 **************** 406 2016-09-17 18:39 36 ***************** ... ..( 2 skipped). .. ***************** 409 2016-09-17 18:42 36 ***************** 410 2016-09-17 18:43 35 **************** 411 2016-09-17 18:44 36 ***************** 412 2016-09-17 18:45 35 **************** ... ..( 9 skipped). .. **************** 422 2016-09-17 18:55 35 **************** 423 2016-09-17 18:56 34 *************** ... ..( 9 skipped). .. *************** 433 2016-09-17 19:06 34 *************** 434 2016-09-17 19:07 ? - 435 2016-09-17 19:08 34 *************** 436 2016-09-17 19:09 ? - 437 2016-09-17 19:10 34 *************** 438 2016-09-17 19:11 ? - 439 2016-09-17 19:12 34 *************** ... ..( 26 skipped). .. *************** 466 2016-09-17 19:39 34 *************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 28 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 28 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 23102 Vendor specific /dev/sdd === START OF INFORMATION SECTION === Device Model: SPCC Solid State Disk Serial Number: -- Firmware Version: S9FM02.6 User Capacity: 120 034 123 776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Sep 17 19:39:26 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 9 Power_On_Hours -O--C- 100 100 000 - 2021 12 Power_Cycle_Count -O--C- 100 100 000 - 415 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO--C- 100 100 010 - 24 173 Unknown_Attribute ------ 100 100 000 - 21364758 192 Power-Off_Retract_Count -O--C- 100 100 000 - 4 194 Temperature_Celsius PO---K 070 070 000 - 30 196 Reallocated_Event_Count ------ 100 100 000 - 0 218 Unknown_Attribute ------ 100 100 000 - 0 241 Total_LBAs_Written -O--C- 100 100 000 - 1442769 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 31 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 31 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC