/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68AX9N0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 20 17:03:22 2019 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 407) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 169 3 Spin_Up_Time POS--K 178 177 021 - 6091 4 Start_Stop_Count -O--CK 100 100 000 - 52 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 020 020 000 - 58431 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 52 192 Power-Off_Retract_Count -O--CK 200 200 000 - 30 193 Load_Cycle_Count -O--CK 200 200 000 - 21 194 Temperature_Celsius -O---K 120 108 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 140 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 140 [19] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 48 40 00 Error: UNC at LBA = 0x1a6c2848 = 443295816 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 90 00 00 cc 0d dc 00 40 08 27d+18:33:18.918 READ FPDMA QUEUED 60 04 00 00 88 00 00 cd eb a0 00 40 08 27d+18:33:18.918 READ FPDMA QUEUED 60 04 00 00 80 00 00 cd eb a8 00 40 08 27d+18:33:18.918 READ FPDMA QUEUED 60 00 08 00 78 00 00 1a 6c 28 48 40 08 27d+18:33:18.918 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 27d+18:33:18.918 SET FEATURES [Enable SATA feature] Error 139 [18] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 40 40 00 Error: UNC at LBA = 0x1a6c2840 = 443295808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 1a 6c 28 40 40 08 27d+18:33:16.063 READ FPDMA QUEUED 60 00 08 00 e0 00 00 1a 6c 28 48 40 08 27d+18:33:16.063 READ FPDMA QUEUED 60 04 00 00 d8 00 00 cd eb a8 00 40 08 27d+18:33:16.063 READ FPDMA QUEUED 60 04 00 00 d0 00 00 cd eb a0 00 40 08 27d+18:33:16.063 READ FPDMA QUEUED 60 00 10 00 c8 00 00 cc 0d dc 00 40 08 27d+18:33:16.063 READ FPDMA QUEUED Error 138 [17] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 38 40 00 Error: UNC at LBA = 0x1a6c2838 = 443295800 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 30 00 00 cd eb a0 00 40 08 27d+18:33:13.201 READ FPDMA QUEUED 60 04 00 00 28 00 00 cd eb a8 00 40 08 27d+18:33:13.201 READ FPDMA QUEUED 60 00 08 00 20 00 00 1a 6c 28 48 40 08 27d+18:33:13.201 READ FPDMA QUEUED 60 00 08 00 18 00 00 1a 6c 28 40 40 08 27d+18:33:13.201 READ FPDMA QUEUED 60 00 08 00 10 00 00 1a 6c 28 38 40 08 27d+18:33:13.201 READ FPDMA QUEUED Error 137 [16] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 30 40 00 Error: UNC at LBA = 0x1a6c2830 = 443295792 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 00 1a 6c 28 30 40 08 27d+18:33:10.334 READ FPDMA QUEUED 60 00 08 00 78 00 00 1a 6c 28 38 40 08 27d+18:33:10.334 READ FPDMA QUEUED 60 00 08 00 70 00 00 1a 6c 28 40 40 08 27d+18:33:10.334 READ FPDMA QUEUED 60 00 08 00 68 00 00 1a 6c 28 48 40 08 27d+18:33:10.334 READ FPDMA QUEUED 60 04 00 00 60 00 00 cd eb a8 00 40 08 27d+18:33:10.334 READ FPDMA QUEUED Error 136 [15] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 28 40 00 Error: WP at LBA = 0x1a6c2828 = 443295784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 02 30 00 d0 00 00 1a 6c 31 d0 40 08 27d+18:33:07.459 WRITE FPDMA QUEUED 60 04 00 00 c0 00 00 cd eb a0 00 40 08 27d+18:33:07.459 READ FPDMA QUEUED 60 04 00 00 b8 00 00 cd eb a8 00 40 08 27d+18:33:07.459 READ FPDMA QUEUED 60 00 08 00 b0 00 00 1a 6c 28 48 40 08 27d+18:33:07.459 READ FPDMA QUEUED 60 00 08 00 a8 00 00 1a 6c 28 40 40 08 27d+18:33:07.459 READ FPDMA QUEUED Error 135 [14] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 18 40 00 Error: UNC at LBA = 0x1a6c2818 = 443295768 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f8 00 00 1a 6c 28 10 40 08 27d+18:33:04.609 READ FPDMA QUEUED 60 00 08 00 f0 00 00 1a 6c 28 18 40 08 27d+18:33:04.609 READ FPDMA QUEUED 60 00 08 00 e8 00 00 1a 6c 28 20 40 08 27d+18:33:04.609 READ FPDMA QUEUED 60 00 08 00 e0 00 00 1a 6c 28 28 40 08 27d+18:33:04.609 READ FPDMA QUEUED 60 00 08 00 d8 00 00 1a 6c 28 30 40 08 27d+18:33:04.609 READ FPDMA QUEUED Error 134 [13] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 08 40 00 Error: UNC at LBA = 0x1a6c2808 = 443295752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 68 00 00 1a 6c 28 48 40 08 27d+18:33:01.710 READ FPDMA QUEUED 60 00 08 00 60 00 00 1a 6c 28 40 40 08 27d+18:33:01.710 READ FPDMA QUEUED 60 00 08 00 58 00 00 1a 6c 28 38 40 08 27d+18:33:01.710 READ FPDMA QUEUED 60 00 08 00 50 00 00 1a 6c 28 30 40 08 27d+18:33:01.710 READ FPDMA QUEUED 60 00 08 00 48 00 00 1a 6c 28 28 40 08 27d+18:33:01.709 READ FPDMA QUEUED Error 133 [12] occurred at disk power-on lifetime: 55915 hours (2329 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 6c 28 08 40 00 Error: UNC at LBA = 0x1a6c2808 = 443295752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 b8 00 00 cd eb a8 00 40 08 27d+18:32:57.733 READ FPDMA QUEUED 60 04 00 00 b0 00 00 cd eb a0 00 40 08 27d+18:32:57.733 READ FPDMA QUEUED 60 04 00 00 a8 00 00 cd eb 9c 00 40 08 27d+18:32:57.728 READ FPDMA QUEUED 60 00 50 00 a0 00 00 1a 6c 28 00 40 08 27d+18:32:57.587 READ FPDMA QUEUED 61 00 c0 00 98 00 00 1a 6c 24 00 40 08 27d+18:32:57.586 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 25/42 Celsius Lifetime Min/Max Temperature: 2/42 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (323) Index Estimated Time Temperature Celsius 324 2019-10-20 09:06 30 *********** ... ..( 40 skipped). .. *********** 365 2019-10-20 09:47 30 *********** 366 2019-10-20 09:48 31 ************ ... ..( 80 skipped). .. ************ 447 2019-10-20 11:09 31 ************ 448 2019-10-20 11:10 32 ************* ... ..( 32 skipped). .. ************* 3 2019-10-20 11:43 32 ************* 4 2019-10-20 11:44 33 ************** ... ..( 34 skipped). .. ************** 39 2019-10-20 12:19 33 ************** 40 2019-10-20 12:20 34 *************** ... ..( 24 skipped). .. *************** 65 2019-10-20 12:45 34 *************** 66 2019-10-20 12:46 33 ************** ... ..( 3 skipped). .. ************** 70 2019-10-20 12:50 33 ************** 71 2019-10-20 12:51 32 ************* ... ..( 12 skipped). .. ************* 84 2019-10-20 13:04 32 ************* 85 2019-10-20 13:05 31 ************ ... ..( 13 skipped). .. ************ 99 2019-10-20 13:19 31 ************ 100 2019-10-20 13:20 30 *********** ... ..( 4 skipped). .. *********** 105 2019-10-20 13:25 30 *********** 106 2019-10-20 13:26 29 ********** ... ..(140 skipped). .. ********** 247 2019-10-20 15:47 29 ********** 248 2019-10-20 15:48 28 ********* ... ..( 51 skipped). .. ********* 300 2019-10-20 16:40 28 ********* 301 2019-10-20 16:41 29 ********** ... ..( 21 skipped). .. ********** 323 2019-10-20 17:03 29 ********** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 24 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 24 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 20045479 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68AX9N0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 20 17:03:22 2019 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (38640) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 388) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 180 179 021 - 5991 4 Start_Stop_Count -O--CK 100 100 000 - 52 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 020 020 000 - 58431 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 52 192 Power-Off_Retract_Count -O--CK 200 200 000 - 30 193 Load_Cycle_Count -O--CK 200 200 000 - 21 194 Temperature_Celsius -O---K 119 107 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 26/43 Celsius Lifetime Min/Max Temperature: 19/43 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (358) Index Estimated Time Temperature Celsius 359 2019-10-20 09:06 30 *********** ... ..( 9 skipped). .. *********** 369 2019-10-20 09:16 30 *********** 370 2019-10-20 09:17 31 ************ ... ..( 87 skipped). .. ************ 458 2019-10-20 10:45 31 ************ 459 2019-10-20 10:46 32 ************* ... ..( 35 skipped). .. ************* 17 2019-10-20 11:22 32 ************* 18 2019-10-20 11:23 33 ************** ... ..( 41 skipped). .. ************** 60 2019-10-20 12:05 33 ************** 61 2019-10-20 12:06 34 *************** ... ..( 42 skipped). .. *************** 104 2019-10-20 12:49 34 *************** 105 2019-10-20 12:50 33 ************** ... ..( 5 skipped). .. ************** 111 2019-10-20 12:56 33 ************** 112 2019-10-20 12:57 32 ************* ... ..( 18 skipped). .. ************* 131 2019-10-20 13:16 32 ************* 132 2019-10-20 13:17 31 ************ ... ..( 7 skipped). .. ************ 140 2019-10-20 13:25 31 ************ 141 2019-10-20 13:26 29 ********** ... ..(201 skipped). .. ********** 343 2019-10-20 16:48 29 ********** 344 2019-10-20 16:49 30 *********** ... ..( 13 skipped). .. *********** 358 2019-10-20 17:03 30 *********** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 24 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 20045598 Vendor specific /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68AX9N0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 20 17:03:22 2019 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (39840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 399) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 182 182 021 - 5875 4 Start_Stop_Count -O--CK 100 100 000 - 52 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 020 020 000 - 58430 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 52 192 Power-Off_Retract_Count -O--CK 200 200 000 - 30 193 Load_Cycle_Count -O--CK 200 200 000 - 21 194 Temperature_Celsius -O---K 120 107 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 25/42 Celsius Lifetime Min/Max Temperature: 20/43 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (307) Index Estimated Time Temperature Celsius 308 2019-10-20 09:06 29 ********** ... ..( 42 skipped). .. ********** 351 2019-10-20 09:49 29 ********** 352 2019-10-20 09:50 30 *********** ... ..( 25 skipped). .. *********** 378 2019-10-20 10:16 30 *********** 379 2019-10-20 10:17 31 ************ ... ..( 87 skipped). .. ************ 467 2019-10-20 11:45 31 ************ 468 2019-10-20 11:46 32 ************* ... ..( 72 skipped). .. ************* 63 2019-10-20 12:59 32 ************* 64 2019-10-20 13:00 31 ************ ... ..( 9 skipped). .. ************ 74 2019-10-20 13:10 31 ************ 75 2019-10-20 13:11 30 *********** ... ..( 13 skipped). .. *********** 89 2019-10-20 13:25 30 *********** 90 2019-10-20 13:26 29 ********** ... ..(141 skipped). .. ********** 232 2019-10-20 15:48 29 ********** 233 2019-10-20 15:49 28 ********* ... ..( 61 skipped). .. ********* 295 2019-10-20 16:51 28 ********* 296 2019-10-20 16:52 29 ********** ... ..( 10 skipped). .. ********** 307 2019-10-20 17:03 29 ********** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 24 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 20045315 Vendor specific /dev/sdd === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68AX9N0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 20 17:03:22 2019 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (41460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 416) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 25 3 Spin_Up_Time POS--K 175 175 021 - 6216 4 Start_Stop_Count -O--CK 100 100 000 - 54 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 021 021 000 - 58392 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 54 192 Power-Off_Retract_Count -O--CK 200 200 000 - 34 193 Load_Cycle_Count -O--CK 200 200 000 - 19 194 Temperature_Celsius -O---K 121 108 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 56694 hours (2362 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 43 d8 40 00 Error: WP at LBA = 0x100bf43d8 = 4307502040 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 c0 00 01 00 bf 43 d0 40 08 12d+03:47:15.629 WRITE FPDMA QUEUED 60 00 08 00 b8 00 01 00 bf 40 f8 40 08 12d+03:47:15.629 READ FPDMA QUEUED 60 00 08 00 b0 00 01 00 bf 40 f0 40 08 12d+03:47:15.629 READ FPDMA QUEUED 60 00 08 00 a8 00 01 00 bf 40 e8 40 08 12d+03:47:15.629 READ FPDMA QUEUED 60 00 08 00 10 00 01 00 bf 40 e0 40 08 12d+03:47:15.629 READ FPDMA QUEUED Error 11 [10] occurred at disk power-on lifetime: 56694 hours (2362 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 43 d0 40 00 Error: UNC at LBA = 0x100bf43d0 = 4307502032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 01 00 bf 43 e0 40 08 12d+03:47:11.781 READ FPDMA QUEUED 60 00 08 00 08 00 01 00 bf 43 d8 40 08 12d+03:47:11.760 READ FPDMA QUEUED 60 00 08 00 a0 00 01 00 bf 43 d0 40 08 12d+03:47:11.747 READ FPDMA QUEUED 60 00 08 00 98 00 01 00 bf 40 c8 40 08 12d+03:47:11.747 READ FPDMA QUEUED 60 00 08 00 90 00 01 00 bf 40 c0 40 08 12d+03:47:11.747 READ FPDMA QUEUED Error 10 [9] occurred at disk power-on lifetime: 56694 hours (2362 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 43 d0 40 00 Error: UNC at LBA = 0x100bf43d0 = 4307502032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 d0 00 01 00 bf 40 00 40 08 12d+03:47:08.380 READ FPDMA QUEUED 60 03 d0 00 c8 00 01 00 bf 3c 00 40 08 12d+03:47:08.380 READ FPDMA QUEUED 60 00 30 00 c0 00 01 00 bf 3f d0 40 08 12d+03:47:08.380 READ FPDMA QUEUED 60 01 10 00 b8 00 01 00 bf 34 00 40 08 12d+03:47:08.279 READ FPDMA QUEUED 60 02 f0 00 b0 00 01 00 bf 35 10 40 08 12d+03:47:08.278 READ FPDMA QUEUED Error 9 [8] occurred at disk power-on lifetime: 56312 hours (2346 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 43 d8 40 00 Error: UNC at LBA = 0x100bf43d8 = 4307502040 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 01 00 bf 43 98 40 08 45d+22:19:21.943 READ FPDMA QUEUED 60 00 08 00 90 00 01 00 bf 43 90 40 08 45d+22:19:21.943 READ FPDMA QUEUED 60 00 08 00 98 00 01 00 bf 43 88 40 08 45d+22:19:21.943 READ FPDMA QUEUED 60 00 08 00 a0 00 01 00 bf 43 80 40 08 45d+22:19:21.943 READ FPDMA QUEUED 60 00 08 00 b0 00 01 00 bf 43 78 40 08 45d+22:19:21.943 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 56312 hours (2346 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 43 d0 40 00 Error: UNC at LBA = 0x100bf43d0 = 4307502032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d0 00 01 00 bf 40 50 40 08 45d+22:19:19.005 READ FPDMA QUEUED 60 00 08 00 c8 00 01 00 bf 40 58 40 08 45d+22:19:19.005 READ FPDMA QUEUED 60 00 08 00 d8 00 01 00 bf 40 60 40 08 45d+22:19:18.962 READ FPDMA QUEUED 60 00 08 00 c0 00 01 00 bf 40 68 40 08 45d+22:19:18.962 READ FPDMA QUEUED 60 00 08 00 b8 00 01 00 bf 40 70 40 08 45d+22:19:18.961 READ FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 56312 hours (2346 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 43 d0 40 00 Error: UNC at LBA = 0x100bf43d0 = 4307502032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 a0 00 01 00 bf 40 00 40 08 45d+22:19:15.883 READ FPDMA QUEUED 60 04 00 00 98 00 01 00 bf 3c 00 40 08 45d+22:19:15.883 READ FPDMA QUEUED 60 00 90 00 90 00 01 00 bf 34 00 40 08 45d+22:19:15.783 READ FPDMA QUEUED 60 03 70 00 88 00 01 00 bf 34 90 40 08 45d+22:19:15.783 READ FPDMA QUEUED 60 08 00 00 80 00 01 00 bf 2c 00 40 08 45d+22:19:15.702 READ FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 48253 hours (2010 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 33 c8 40 00 Error: UNC at LBA = 0x100bf33c8 = 4307497928 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 00 00 78 00 01 00 bf 2c 00 40 08 9d+21:56:38.903 READ FPDMA QUEUED 60 04 00 00 70 00 01 00 bf 24 00 40 08 9d+21:56:32.791 READ FPDMA QUEUED 60 08 00 00 68 00 01 00 bf 1c 00 40 08 9d+21:56:32.656 READ FPDMA QUEUED 60 04 00 00 60 00 01 00 bf 14 00 40 08 9d+21:56:32.538 READ FPDMA QUEUED 60 08 00 00 58 00 01 00 bf 0c 00 40 08 9d+21:56:31.318 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 31600 hours (1316 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 00 bf 43 d0 40 00 Error: UNC at LBA = 0x100bf43d0 = 4307502032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 38 00 88 00 01 00 bf 43 c8 40 08 6d+22:16:19.065 READ FPDMA QUEUED 60 00 80 00 80 00 01 00 bf 47 48 40 08 6d+22:16:19.065 READ FPDMA QUEUED 60 00 80 00 78 00 01 00 bf 46 c8 40 08 6d+22:16:19.064 READ FPDMA QUEUED 60 00 80 00 70 00 01 00 bf 46 48 40 08 6d+22:16:19.064 READ FPDMA QUEUED 60 00 80 00 68 00 01 00 bf 45 c8 40 08 6d+22:16:19.064 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 25/41 Celsius Lifetime Min/Max Temperature: 19/42 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (412) Index Estimated Time Temperature Celsius 413 2019-10-20 09:06 28 ********* ... ..( 59 skipped). .. ********* 473 2019-10-20 10:06 28 ********* 474 2019-10-20 10:07 29 ********** ... ..( 25 skipped). .. ********** 22 2019-10-20 10:33 29 ********** 23 2019-10-20 10:34 30 *********** ... ..( 52 skipped). .. *********** 76 2019-10-20 11:27 30 *********** 77 2019-10-20 11:28 31 ************ ... ..( 83 skipped). .. ************ 161 2019-10-20 12:52 31 ************ 162 2019-10-20 12:53 30 *********** ... ..( 8 skipped). .. *********** 171 2019-10-20 13:02 30 *********** 172 2019-10-20 13:03 29 ********** ... ..( 21 skipped). .. ********** 194 2019-10-20 13:25 29 ********** 195 2019-10-20 13:26 28 ********* ... ..(156 skipped). .. ********* 352 2019-10-20 16:03 28 ********* 353 2019-10-20 16:04 27 ******** ... ..( 36 skipped). .. ******** 390 2019-10-20 16:41 27 ******** 391 2019-10-20 16:42 28 ********* ... ..( 20 skipped). .. ********* 412 2019-10-20 17:03 28 ********* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 24 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 20045660 Vendor specific /dev/sde === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-00ERMA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 15.01H15 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Oct 20 17:03:22 2019 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8700) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 88) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 138 137 021 - 4091 4 Start_Stop_Count -O--CK 100 100 000 - 36 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 066 065 000 - 25169 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 35 192 Power-Off_Retract_Count -O--CK 200 200 000 - 22 193 Load_Cycle_Count -O--CK 200 200 000 - 59 194 Temperature_Celsius -O---K 112 093 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 1 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 26/44 Celsius Lifetime Min/Max Temperature: 0/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (22) Index Estimated Time Temperature Celsius 23 2019-10-20 09:06 31 ************ ... ..( 8 skipped). .. ************ 32 2019-10-20 09:15 31 ************ 33 2019-10-20 09:16 32 ************* ... ..( 2 skipped). .. ************* 36 2019-10-20 09:19 32 ************* 37 2019-10-20 09:20 31 ************ ... ..( 2 skipped). .. ************ 40 2019-10-20 09:23 31 ************ 41 2019-10-20 09:24 32 ************* 42 2019-10-20 09:25 32 ************* 43 2019-10-20 09:26 31 ************ 44 2019-10-20 09:27 32 ************* 45 2019-10-20 09:28 32 ************* 46 2019-10-20 09:29 31 ************ 47 2019-10-20 09:30 31 ************ 48 2019-10-20 09:31 32 ************* ... ..( 58 skipped). .. ************* 107 2019-10-20 10:30 32 ************* 108 2019-10-20 10:31 33 ************** ... ..( 40 skipped). .. ************** 149 2019-10-20 11:12 33 ************** 150 2019-10-20 11:13 34 *************** 151 2019-10-20 11:14 33 ************** 152 2019-10-20 11:15 33 ************** 153 2019-10-20 11:16 34 *************** ... ..( 38 skipped). .. *************** 192 2019-10-20 11:55 34 *************** 193 2019-10-20 11:56 35 **************** 194 2019-10-20 11:57 34 *************** ... ..( 2 skipped). .. *************** 197 2019-10-20 12:00 34 *************** 198 2019-10-20 12:01 35 **************** 199 2019-10-20 12:02 34 *************** 200 2019-10-20 12:03 35 **************** 201 2019-10-20 12:04 34 *************** 202 2019-10-20 12:05 34 *************** 203 2019-10-20 12:06 35 **************** 204 2019-10-20 12:07 34 *************** 205 2019-10-20 12:08 35 **************** 206 2019-10-20 12:09 34 *************** ... ..( 2 skipped). .. *************** 209 2019-10-20 12:12 34 *************** 210 2019-10-20 12:13 35 **************** ... ..( 2 skipped). .. **************** 213 2019-10-20 12:16 35 **************** 214 2019-10-20 12:17 34 *************** 215 2019-10-20 12:18 35 **************** ... ..( 3 skipped). .. **************** 219 2019-10-20 12:22 35 **************** 220 2019-10-20 12:23 34 *************** ... ..( 2 skipped). .. *************** 223 2019-10-20 12:26 34 *************** 224 2019-10-20 12:27 33 ************** ... ..( 4 skipped). .. ************** 229 2019-10-20 12:32 33 ************** 230 2019-10-20 12:33 32 ************* ... ..( 6 skipped). .. ************* 237 2019-10-20 12:40 32 ************* 238 2019-10-20 12:41 31 ************ ... ..( 15 skipped). .. ************ 254 2019-10-20 12:57 31 ************ 255 2019-10-20 12:58 30 *********** 256 2019-10-20 12:59 31 ************ 257 2019-10-20 13:00 30 *********** 258 2019-10-20 13:01 31 ************ 259 2019-10-20 13:02 31 ************ 260 2019-10-20 13:03 31 ************ 261 2019-10-20 13:04 30 *********** ... ..(126 skipped). .. *********** 388 2019-10-20 15:11 30 *********** 389 2019-10-20 15:12 29 ********** ... ..( 38 skipped). .. ********** 428 2019-10-20 15:51 29 ********** 429 2019-10-20 15:52 28 ********* 430 2019-10-20 15:53 29 ********** 431 2019-10-20 15:54 29 ********** 432 2019-10-20 15:55 28 ********* 433 2019-10-20 15:56 29 ********** ... ..( 15 skipped). .. ********** 449 2019-10-20 16:12 29 ********** 450 2019-10-20 16:13 30 *********** ... ..( 21 skipped). .. *********** 472 2019-10-20 16:35 30 *********** 473 2019-10-20 16:36 31 ************ ... ..( 3 skipped). .. ************ 477 2019-10-20 16:40 31 ************ 0 2019-10-20 16:41 30 *********** 1 2019-10-20 16:42 31 ************ ... ..( 20 skipped). .. ************ 22 2019-10-20 17:03 31 ************ SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 20044892 Vendor specific