/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate SV35 Device Model: ST1000VX000-1CU162 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CV22 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Apr 29 21:52:41 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 80) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 115) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10b9) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 119 099 006 - 210581168 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 093 093 020 - 7651 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 081 060 030 - 154605372 9 Power_On_Hours -O--CK 078 078 000 - 19411 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 095 095 020 - 5957 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 099 000 - 4 189 High_Fly_Writes -O-RCK 001 001 000 - 1187 190 Airflow_Temperature_Cel -O---K 070 059 045 - 30 (Min/Max 21/31) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 126 193 Load_Cycle_Count -O--CK 097 097 000 - 7761 194 Temperature_Celsius -O---K 030 041 000 - 30 (0 16 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1371 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 21/31 Celsius Lifetime Min/Max Temperature: 16/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 94 minutes Min/Max recommended Temperature: 1/61 Celsius Min/Max Temperature Limit: 2/60 Celsius Temperature History Size (Index): 128 (119) Index Estimated Time Temperature Celsius 120 2018-04-21 14:52 ? - 121 2018-04-21 16:26 26 ******* 122 2018-04-21 18:00 30 *********** 123 2018-04-21 19:34 ? - 124 2018-04-21 21:08 22 *** 125 2018-04-21 22:42 30 *********** 126 2018-04-22 00:16 30 *********** 127 2018-04-22 01:50 ? - 0 2018-04-22 03:24 22 *** 1 2018-04-22 04:58 ? - 2 2018-04-22 06:32 22 *** 3 2018-04-22 08:06 30 *********** 4 2018-04-22 09:40 ? - 5 2018-04-22 11:14 23 **** 6 2018-04-22 12:48 30 *********** 7 2018-04-22 14:22 ? - 8 2018-04-22 15:56 24 ***** 9 2018-04-22 17:30 31 ************ 10 2018-04-22 19:04 31 ************ 11 2018-04-22 20:38 30 *********** 12 2018-04-22 22:12 ? - 13 2018-04-22 23:46 22 *** 14 2018-04-23 01:20 ? - 15 2018-04-23 02:54 23 **** 16 2018-04-23 04:28 30 *********** 17 2018-04-23 06:02 31 ************ 18 2018-04-23 07:36 30 *********** 19 2018-04-23 09:10 30 *********** 20 2018-04-23 10:44 ? - 21 2018-04-23 12:18 23 **** 22 2018-04-23 13:52 30 *********** 23 2018-04-23 15:26 30 *********** 24 2018-04-23 17:00 30 *********** 25 2018-04-23 18:34 ? - 26 2018-04-23 20:08 22 *** 27 2018-04-23 21:42 ? - 28 2018-04-23 23:16 22 *** 29 2018-04-24 00:50 ? - 30 2018-04-24 02:24 24 ***** 31 2018-04-24 03:58 29 ********** 32 2018-04-24 05:32 29 ********** 33 2018-04-24 07:06 ? - 34 2018-04-24 08:40 22 *** 35 2018-04-24 10:14 29 ********** 36 2018-04-24 11:48 30 *********** 37 2018-04-24 13:22 30 *********** 38 2018-04-24 14:56 ? - 39 2018-04-24 16:30 21 ** 40 2018-04-24 18:04 ? - 41 2018-04-24 19:38 22 *** 42 2018-04-24 21:12 ? - 43 2018-04-24 22:46 26 ******* 44 2018-04-25 00:20 24 ***** 45 2018-04-25 01:54 27 ******** 46 2018-04-25 03:28 ? - 47 2018-04-25 05:02 21 ** 48 2018-04-25 06:36 29 ********** 49 2018-04-25 08:10 29 ********** 50 2018-04-25 09:44 29 ********** 51 2018-04-25 11:18 ? - 52 2018-04-25 12:52 21 ** 53 2018-04-25 14:26 ? - 54 2018-04-25 16:00 22 *** 55 2018-04-25 17:34 29 ********** 56 2018-04-25 19:08 29 ********** 57 2018-04-25 20:42 29 ********** 58 2018-04-25 22:16 ? - 59 2018-04-25 23:50 22 *** 60 2018-04-26 01:24 29 ********** 61 2018-04-26 02:58 30 *********** 62 2018-04-26 04:32 30 *********** 63 2018-04-26 06:06 ? - 64 2018-04-26 07:40 21 ** 65 2018-04-26 09:14 ? - 66 2018-04-26 10:48 22 *** 67 2018-04-26 12:22 ? - 68 2018-04-26 13:56 23 **** 69 2018-04-26 15:30 29 ********** 70 2018-04-26 17:04 29 ********** 71 2018-04-26 18:38 ? - 72 2018-04-26 20:12 22 *** 73 2018-04-26 21:46 30 *********** 74 2018-04-26 23:20 29 ********** 75 2018-04-27 00:54 29 ********** 76 2018-04-27 02:28 ? - 77 2018-04-27 04:02 21 ** 78 2018-04-27 05:36 ? - 79 2018-04-27 07:10 22 *** 80 2018-04-27 08:44 ? - 81 2018-04-27 10:18 23 **** 82 2018-04-27 11:52 ? - 83 2018-04-27 13:26 23 **** 84 2018-04-27 15:00 ? - 85 2018-04-27 16:34 24 ***** 86 2018-04-27 18:08 ? - 87 2018-04-27 19:42 24 ***** 88 2018-04-27 21:16 ? - 89 2018-04-27 22:50 24 ***** 90 2018-04-28 00:24 ? - 91 2018-04-28 01:58 25 ****** 92 2018-04-28 03:32 ? - 93 2018-04-28 05:06 25 ****** 94 2018-04-28 06:40 ? - 95 2018-04-28 08:14 25 ****** 96 2018-04-28 09:48 ? - 97 2018-04-28 11:22 26 ******* 98 2018-04-28 12:56 ? - 99 2018-04-28 14:30 26 ******* 100 2018-04-28 16:04 ? - 101 2018-04-28 17:38 26 ******* 102 2018-04-28 19:12 ? - 103 2018-04-28 20:46 26 ******* 104 2018-04-28 22:20 ? - 105 2018-04-28 23:54 21 ** 106 2018-04-29 01:28 ? - 107 2018-04-29 03:02 21 ** 108 2018-04-29 04:36 ? - 109 2018-04-29 06:10 23 **** 110 2018-04-29 07:44 ? - 111 2018-04-29 09:18 23 **** 112 2018-04-29 10:52 ? - 113 2018-04-29 12:26 25 ****** 114 2018-04-29 14:00 31 ************ 115 2018-04-29 15:34 ? - 116 2018-04-29 17:08 21 ** 117 2018-04-29 18:42 30 *********** 118 2018-04-29 20:16 30 *********** 119 2018-04-29 21:50 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 75 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: OCZ-VERTEX2 Serial Number: -- LU WWN Device Id: 5 e83a97 ... Firmware Version: 1.37 User Capacity: 60,022,480,896 bytes [60.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Apr 29 21:52:41 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown (0x100) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7f) SMART execute Offline immediate. Auto Offline data collection on/off support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 5) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 104 099 050 - 0/7562316 5 Retired_Block_Count PO--CK 100 100 003 - 0 9 Power_On_Hours_and_Msec -O--CK 100 100 000 - 32227h+47m+44.550s 12 Power_Cycle_Count -O--CK 093 093 000 - 7300 171 Program_Fail_Count -O--CK 000 000 000 - 0 172 Erase_Fail_Count -O--CK 000 000 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 000 000 000 - 231 177 Wear_Range_Delta ------ 000 000 000 - 4 181 Program_Fail_Count -O--CK 000 000 000 - 0 182 Erase_Fail_Count -O--CK 000 000 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 030 030 000 - 30 (Min/Max 30/30) 195 ECC_Uncorr_Error_Count --SRC- 104 099 000 - 0/7562316 196 Reallocated_Event_Count PO--CK 100 100 000 - 0 231 SSD_Life_Left PO--C- 098 098 010 - 0 233 SandForce_Internal ------ 000 000 000 - 17152 234 SandForce_Internal -O--CK 000 000 000 - 11328 241 Lifetime_Writes_GiB -O--CK 000 000 000 - 11328 242 Lifetime_Reads_GiB -O--CK 000 000 000 - 26176 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb7 GPL,SL VS 16 Device vendor specific log 0xc0-0xc1 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Self-test routine in progress 90% 8521 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) SCT Support Level: 1 Device State: Active (0) Current Temperature: ? Celsius Power Cycle Min/Max Temperature: 127/-127 Celsius Lifetime Min/Max Temperature: 127/-127 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 478 (479) Invalid Temperature History Size or Index SCT Error Recovery Control: Read: 256 (25.6 seconds) Write: 256 (25.6 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 6496 Device-to-host register FISes sent due to a COMRESET /dev/sdc === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3250820A Serial Number: -- Firmware Version: 3.AAC User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Apr 29 21:52:42 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 92) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 095 006 - 118447603 3 Spin_Up_Time PO---- 091 089 000 - 0 4 Start_Stop_Count -O--CK 084 084 020 - 16711 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 240200556 9 Power_On_Hours -O--CK 062 062 000 - 34127 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 095 095 020 - 5293 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 062 044 045 Past 38 (Min/Max 22/40) 194 Temperature_Celsius -O---K 038 056 000 - 38 (0 12 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 055 052 000 - 9357742 197 Current_Pending_Sector -O--C- 001 001 000 - 4294967295 198 Offline_Uncorrectable ----C- 001 001 000 - 4294967295 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23552 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 1c 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x1c0a5fa074a0 = 30830879601824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:30:03.816 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.809 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:30:03.802 IDENTIFY DEVICE ef 00 03 00 42 00 ff ff 00 ff ff a0 00 00:30:03.750 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.743 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 11 [10] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 1c 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x1c0a5fa074a0 = 30830879601824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:30:03.816 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.809 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:30:03.802 IDENTIFY DEVICE ef 00 03 00 42 00 ff ff 00 ff ff a0 00 00:30:03.750 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.743 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 10 [9] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 1c 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x1c0a5fa074a0 = 30830879601824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:29:59.347 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:29:59.345 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:29:59.343 IDENTIFY DEVICE ef 00 03 00 42 00 ff ff 00 ff ff a0 00 00:29:59.341 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:29:59.339 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 9 [8] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 74 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x740a5fa074a0 = 127587902846112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:29:59.347 READ DMA c8 00 00 00 80 00 0a 56 00 74 d7 ea 00 00:29:59.345 READ DMA c8 00 00 00 80 00 0a 56 00 74 57 ea 00 00:29:59.343 READ DMA c8 00 00 00 80 00 0a 55 00 74 d7 ea 00 00:29:59.341 READ DMA c8 00 00 00 80 00 0a 55 00 74 57 ea 00 00:29:59.339 READ DMA Error 8 [7] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 1c 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x1c0a5fa074a0 = 30830879601824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:30:03.816 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.809 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:30:03.802 IDENTIFY DEVICE ef 00 03 00 42 00 ff ff 00 ff ff a0 00 00:30:03.750 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.743 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 7 [6] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 1c 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x1c0a5fa074a0 = 30830879601824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:30:03.816 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.809 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:30:03.802 IDENTIFY DEVICE ef 00 03 00 42 00 ff ff 00 ff ff a0 00 00:30:03.750 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:30:03.743 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 6 [5] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 1c 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x1c0a5fa074a0 = 30830879601824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:29:59.347 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:29:59.345 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:29:59.343 IDENTIFY DEVICE ef 00 03 00 42 00 ff ff 00 ff ff a0 00 00:29:59.341 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:29:59.339 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 5 [4] occurred at disk power-on lifetime: 21256 hours (885 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 74 0a 57 a0 74 a0 ea 00 Error: UNC at LBA = 0x740a5fa074a0 = 127587902846112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 80 00 0a 57 00 74 57 ea 00 00:29:59.347 READ DMA c8 00 00 00 80 00 0a 56 00 74 d7 ea 00 00:29:59.345 READ DMA c8 00 00 00 80 00 0a 56 00 74 57 ea 00 00:29:59.343 READ DMA c8 00 00 00 80 00 0a 55 00 74 d7 ea 00 00:29:59.341 READ DMA c8 00 00 00 80 00 0a 55 00 74 57 ea 00 00:29:59.339 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 30208 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdd === START OF INFORMATION SECTION === Model Family: Plextor M3/M5/M6 Series SSDs Device Model: PLEXTOR PX-128M6S Serial Number: -- LU WWN Device Id: 5 002303 ... Add. Product Id: HC7020S0 Firmware Version: 1.09 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ATA/ATAPI-7 T13/1532D revision 4a SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Apr 29 21:52:42 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 10) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocated_Sector_Ct PO---- 100 100 000 - 0 9 Power_On_Hours -O---- 100 100 000 - 512 12 Power_Cycle_Count PO---- 100 100 000 - 5083 170 Unknown_Plextor_Attrib -O--CK 100 100 000 - 0 171 Unknown_Plextor_Attrib PO---- 100 100 000 - 0 172 Unknown_Plextor_Attrib PO---- 100 100 000 - 0 173 Unknown_Plextor_Attrib PO---- 100 100 000 - 36 174 Unknown_Plextor_Attrib PO---- 100 100 000 - 842 175 Program_Fail_Count_Chip PO---- 100 100 000 - 0 176 Erase_Fail_Count_Chip PO---- 100 100 000 - 0 177 Wear_Leveling_Count PO---- 100 100 000 - 36901 178 Used_Rsvd_Blk_Cnt_Chip PO---- 100 100 000 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO---- 100 100 000 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--CK 100 100 000 - 832 181 Program_Fail_Cnt_Total PO---- 100 100 000 - 0 182 Erase_Fail_Count_Total PO---- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect PO---- 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count PO---- 100 100 000 - 842 195 Hardware_ECC_Recovered PO---- 100 100 000 - 0 196 Reallocated_Event_Count PO---- 100 100 000 - 0 198 Offline_Uncorrectable PO---- 100 100 000 - 0 199 UDMA_CRC_Error_Count PO---- 100 100 000 - 0 232 Available_Reservd_Space PO---- 100 100 010 - 0 233 Media_Wearout_Indicator PO---- 100 100 000 - 4612 241 Host_Writes_32MiB PO---- 100 100 000 - 81056 242 Host_Reads_32MiB PO---- 100 100 000 - 364832 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 0 Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 2 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 1 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 0 No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) SCT Support Level: 1 Device State: Active (0) Current Temperature: ? Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 128 (0) Index Estimated Time Temperature Celsius 1 2018-04-29 19:45 ? - ... ..(126 skipped). .. - 0 2018-04-29 21:52 ? - SCT Error Recovery Control: Read: 2 (0.2 seconds) Write: 2 (0.2 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 83 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3320620AS Serial Number: -- Firmware Version: 3.AAE User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Apr 29 21:52:42 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 115) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 090 006 - 197210916 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 083 083 020 - 17783 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 087 060 030 - 520671944 9 Power_On_Hours -O--CK 045 045 000 - 49032 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 091 091 020 - 9378 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 065 053 045 - 35 (Min/Max 23/36) 194 Temperature_Celsius -O---K 035 047 000 - 35 (0 13 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 064 057 000 - 93703788 197 Current_Pending_Sector -O--C- 100 100 000 - 13 198 Offline_Uncorrectable ----C- 100 100 000 - 13 199 UDMA_CRC_Error_Count -OSRCK 200 198 000 - 77 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 068 221 000 - 32 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 40 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 40 [19] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED Error 39 [18] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED Error 38 [17] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED Error 37 [16] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED Error 36 [15] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED Error 35 [14] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED Error 34 [13] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED Error 33 [12] occurred at disk power-on lifetime: 37642 hours (1568 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 fe 00 00 00 00 00 00 28 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 25 ea 00 42 00 28 00 02:55:45.634 READ LOG EXT 60 00 80 00 80 00 25 ea 00 42 80 00 00 02:55:45.627 READ FPDMA QUEUED 60 00 80 00 80 00 25 ea 00 42 00 00 00 02:55:45.625 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 80 00 00 02:55:45.624 READ FPDMA QUEUED 60 00 80 00 80 00 25 e9 00 42 00 00 00 02:55:45.622 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 31630 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 84 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS