/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-16-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 840 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EXT0BB6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jan 2 17:27:27 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Unexpected SCT status 0x0001 (action_code=4, function_code=2) Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 110) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 096 096 000 - 15480 12 Power_Cycle_Count -O--CK 095 095 000 - 4606 177 Wear_Leveling_Count PO--C- 096 096 000 - 41 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 063 039 000 - 37 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 296 241 Total_LBAs_Written -O--CK 099 099 000 - 33559038086 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 16 Device vendor specific log 0xce GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: ?/ ? Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/92854 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 128 (23) Index Estimated Time Temperature Celsius 24 2024-01-01 20:10 ? - ... ..(103 skipped). .. - 0 2024-01-02 13:30 ? - 1 2024-01-02 13:40 28 ********* 2 2024-01-02 13:50 31 ************ 3 2024-01-02 14:00 33 ************** 4 2024-01-02 14:10 33 ************** 5 2024-01-02 14:20 33 ************** 6 2024-01-02 14:30 34 *************** 7 2024-01-02 14:40 35 **************** ... ..( 3 skipped). .. **************** 11 2024-01-02 15:20 35 **************** 12 2024-01-02 15:30 36 ***************** ... ..( 4 skipped). .. ***************** 17 2024-01-02 16:20 36 ***************** 18 2024-01-02 16:30 35 **************** 19 2024-01-02 16:40 35 **************** 20 2024-01-02 16:50 35 **************** 21 2024-01-02 17:00 36 ***************** 22 2024-01-02 17:10 39 ******************** 23 2024-01-02 17:20 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 20 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-16-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Laptop HDD Device Model: ST500LT012-9WS142 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001SDM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jan 2 17:27:27 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 105) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 099 006 - 79864336 3 Spin_Up_Time PO---- 100 099 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3113 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 078 060 030 - 17416954814 9 Power_On_Hours -O--CK 096 096 000 - 4172 (230 223 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3093 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 072 072 000 - 28 188 Command_Timeout -O--CK 100 095 000 - 73015558168 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 067 043 045 Past 33 (0 13 33 18 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 567 192 Power-Off_Retract_Count -O--CK 100 100 000 - 31 193 Load_Cycle_Count -O--CK 070 070 000 - 60691 194 Temperature_Celsius -O---K 033 057 000 - 33 (0 12 0 0 0) 196 Reallocated_Event_Count POSR-- 096 096 030 - 4016 (45139 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 16 240 Head_Flying_Hours ------ 096 096 000 - 4016 (176 83 0) 241 Total_LBAs_Written ------ 100 253 000 - 3637457446 242 Total_LBAs_Read ------ 100 253 000 - 2189191339 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbd-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 113 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 113 [12] occurred at disk power-on lifetime: 2961 hours (123 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 2a 00 00 Error: UNC at LBA = 0x0f2d972a = 254646058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 06 00 00 0f 2d 97 2a 40 00 10:04:29.746 READ FPDMA QUEUED 61 00 00 00 10 00 00 00 78 f1 b8 40 00 10:04:29.746 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 2f b3 31 70 40 00 10:04:29.718 READ FPDMA QUEUED 61 00 00 00 08 00 00 01 93 c4 98 40 00 10:04:29.717 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 00 56 56 fa 40 00 10:04:29.703 READ FPDMA QUEUED Error 112 [11] occurred at disk power-on lifetime: 2961 hours (123 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 2a 00 00 Error: UNC at LBA = 0x0f2d972a = 254646058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0f 2d 97 2a 40 00 10:04:26.975 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 56 2f f2 40 00 10:04:26.951 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 78 f1 38 40 00 10:04:26.951 WRITE FPDMA QUEUED 60 00 00 00 38 00 00 22 d6 b2 d0 40 00 10:04:26.934 READ FPDMA QUEUED 60 00 00 00 08 00 00 1d 75 5a 38 40 00 10:04:26.915 READ FPDMA QUEUED Error 111 [10] occurred at disk power-on lifetime: 2961 hours (123 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 28 00 00 Error: WP at LBA = 0x0f2d9728 = 254646056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 1d 60 21 60 40 00 10:04:23.892 WRITE FPDMA QUEUED 60 00 00 00 40 00 00 0f 2d 96 fa 40 00 10:04:23.892 READ FPDMA QUEUED 60 00 00 00 20 00 00 19 3c db 98 40 00 10:04:23.892 READ FPDMA QUEUED 60 00 00 00 20 00 00 00 56 7c 35 40 00 10:04:23.892 READ FPDMA QUEUED 61 00 00 01 00 00 00 2e b5 e6 88 40 00 10:04:23.891 WRITE FPDMA QUEUED Error 110 [9] occurred at disk power-on lifetime: 2961 hours (123 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 28 00 00 Error: UNC at LBA = 0x0f2d9728 = 254646056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 0f 2d 96 fa 40 00 10:02:19.477 READ FPDMA QUEUED ec 00 00 00 00 00 00 00 00 00 00 00 00 10:02:19.455 IDENTIFY DEVICE ef 00 10 00 03 00 00 00 00 00 00 00 00 10:02:19.445 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 00 00 10:02:19.335 IDENTIFY DEVICE 00 00 00 00 00 00 00 00 00 00 00 00 ff 10:02:19.308 NOP [Abort queued commands] Error 109 [8] occurred at disk power-on lifetime: 2961 hours (123 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 28 00 00 Error: UNC at LBA = 0x0f2d9728 = 254646056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 0f 2d 96 fa 40 00 10:00:38.772 READ FPDMA QUEUED 60 00 00 00 40 00 00 0f 2d 97 3a 40 00 10:00:38.763 READ FPDMA QUEUED 60 00 00 00 40 00 00 0f 2d 94 72 40 00 10:00:38.762 READ FPDMA QUEUED 60 00 00 00 40 00 00 0f 2d 98 b2 40 00 10:00:38.762 READ FPDMA QUEUED 60 00 00 00 40 00 00 0f 2d 99 0a 40 00 10:00:38.762 READ FPDMA QUEUED Error 108 [7] occurred at disk power-on lifetime: 2941 hours (122 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 2a 00 00 Error: UNC at LBA = 0x0f2d972a = 254646058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 06 00 00 0f 2d 97 2a 40 00 04:53:40.837 READ FPDMA QUEUED 61 00 00 00 08 00 00 2f 9d 1a f8 40 00 04:53:40.837 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 22 e5 5e 18 40 00 04:53:40.837 WRITE FPDMA QUEUED 60 00 00 00 10 00 00 34 59 13 30 40 00 04:53:40.818 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 3c 02 78 40 00 04:53:40.817 READ FPDMA QUEUED Error 107 [6] occurred at disk power-on lifetime: 2941 hours (122 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 2a 00 00 Error: UNC at LBA = 0x0f2d972a = 254646058 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0f 2d 97 2a 40 00 04:53:38.092 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 3c 02 90 40 00 04:53:38.092 READ FPDMA QUEUED 60 00 00 00 20 00 00 0a 92 13 8f 40 00 04:53:38.092 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 78 f1 80 40 00 04:53:38.092 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 00 00 04:53:37.970 FLUSH CACHE EXT Error 106 [5] occurred at disk power-on lifetime: 2941 hours (122 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0f 2d 97 28 00 00 Error: WP at LBA = 0x0f2d9728 = 254646056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 1c f3 bd 88 40 00 04:53:35.059 WRITE FPDMA QUEUED 60 00 00 00 40 00 00 0f 2d 96 fa 40 00 04:53:35.059 READ FPDMA QUEUED 60 00 00 00 10 00 00 0c 55 ba e9 40 00 04:53:35.058 READ FPDMA QUEUED 61 00 00 00 20 00 00 00 78 f1 48 40 00 04:53:35.058 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 1c ca 56 70 40 00 04:53:35.058 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 18/33 Celsius Lifetime Min/Max Temperature: 12/57 Celsius Specified Max Operating Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 30 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2023-12-31 01:30 31 ************ 20 2023-12-31 02:00 31 ************ 21 2023-12-31 02:30 33 ************** 22 2023-12-31 03:00 33 ************** 23 2023-12-31 03:30 32 ************* 24 2023-12-31 04:00 33 ************** 25 2023-12-31 04:30 ? - 26 2023-12-31 05:00 18 - 27 2023-12-31 05:30 19 - 28 2023-12-31 06:00 30 *********** 29 2023-12-31 06:30 31 ************ 30 2023-12-31 07:00 31 ************ 31 2023-12-31 07:30 ? - 32 2023-12-31 08:00 31 ************ 33 2023-12-31 08:30 ? - 34 2023-12-31 09:00 18 - 35 2023-12-31 09:30 ? - 36 2023-12-31 10:00 18 - 37 2023-12-31 10:30 19 - 38 2023-12-31 11:00 ? - 39 2023-12-31 11:30 30 *********** 40 2023-12-31 12:00 ? - 41 2023-12-31 12:30 18 - 42 2023-12-31 13:00 19 - 43 2023-12-31 13:30 28 ********* 44 2023-12-31 14:00 30 *********** 45 2023-12-31 14:30 31 ************ ... ..( 9 skipped). .. ************ 55 2023-12-31 19:30 31 ************ 56 2023-12-31 20:00 ? - 57 2023-12-31 20:30 18 - 58 2023-12-31 21:00 19 - 59 2023-12-31 21:30 30 *********** 60 2023-12-31 22:00 32 ************* 61 2023-12-31 22:30 ? - 62 2023-12-31 23:00 31 ************ 63 2023-12-31 23:30 31 ************ 64 2024-01-01 00:00 33 ************** 65 2024-01-01 00:30 32 ************* 66 2024-01-01 01:00 31 ************ ... ..( 9 skipped). .. ************ 76 2024-01-01 06:00 31 ************ 77 2024-01-01 06:30 ? - 78 2024-01-01 07:00 31 ************ 79 2024-01-01 07:30 31 ************ 80 2024-01-01 08:00 32 ************* ... ..( 23 skipped). .. ************* 104 2024-01-01 20:00 32 ************* 105 2024-01-01 20:30 ? - 106 2024-01-01 21:00 24 ***** 107 2024-01-01 21:30 25 ****** 108 2024-01-01 22:00 31 ************ 109 2024-01-01 22:30 32 ************* ... ..( 2 skipped). .. ************* 112 2024-01-02 00:00 32 ************* 113 2024-01-02 00:30 33 ************** 114 2024-01-02 01:00 33 ************** 115 2024-01-02 01:30 33 ************** 116 2024-01-02 02:00 32 ************* 117 2024-01-02 02:30 32 ************* 118 2024-01-02 03:00 31 ************ 119 2024-01-02 03:30 ? - 120 2024-01-02 04:00 32 ************* 121 2024-01-02 04:30 31 ************ 122 2024-01-02 05:00 34 *************** 123 2024-01-02 05:30 34 *************** 124 2024-01-02 06:00 33 ************** 125 2024-01-02 06:30 33 ************** 126 2024-01-02 07:00 33 ************** 127 2024-01-02 07:30 ? - 0 2024-01-02 08:00 18 - 1 2024-01-02 08:30 19 - 2 2024-01-02 09:00 ? - 3 2024-01-02 09:30 18 - 4 2024-01-02 10:00 19 - 5 2024-01-02 10:30 ? - 6 2024-01-02 11:00 30 *********** 7 2024-01-02 11:30 ? - 8 2024-01-02 12:00 18 - 9 2024-01-02 12:30 ? - 10 2024-01-02 13:00 18 - 11 2024-01-02 13:30 19 - 12 2024-01-02 14:00 30 *********** 13 2024-01-02 14:30 31 ************ 14 2024-01-02 15:00 32 ************* 15 2024-01-02 15:30 32 ************* 16 2024-01-02 16:00 33 ************** 17 2024-01-02 16:30 32 ************* 18 2024-01-02 17:00 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS