/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.4.11-desktop-1omv2390] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar P7K500 Device Model: Hitachi HDP725016GLA380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GMBOA5BA User Capacity: 160,000,000,000 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Sep 2 18:52:43 2023 +06 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3936) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 65) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance --S--- 100 100 054 - 85 3 Spin_Up_Time POS--- 111 111 024 - 182 (Average 185) 4 Start_Stop_Count -O--C- 099 099 000 - 5770 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 1 7 Seek_Error_Rate -O-R-- 100 100 067 - 0 8 Seek_Time_Performance --S--- 136 136 020 - 27 9 Power_On_Hours -O--C- 097 097 000 - 22928 10 Spin_Retry_Count -O--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 5523 192 Power-Off_Retract_Count -O--CK 095 095 000 - 6327 193 Load_Cycle_Count -O--C- 095 095 000 - 6327 194 Temperature_Celsius -O---- 181 181 000 - 33 (Min/Max 2/49) 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 25 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 2631 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2631 [2] occurred at disk power-on lifetime: 22173 hours (923 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 09 ef ae 13 49 00 Error: UNC 5 sectors at LBA = 0x09efae13 = 166702611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 09 ef ae 10 40 00 01:21:25.400 READ DMA EXT 25 00 00 00 28 00 00 09 ef ae 10 40 00 01:21:21.200 READ DMA EXT 25 00 00 00 40 00 00 00 c2 0b 70 40 00 01:21:21.200 READ DMA EXT 25 00 00 00 08 00 00 09 ef ae 10 40 00 01:21:16.900 READ DMA EXT 25 00 00 00 08 00 00 09 ef ae 30 40 00 01:21:16.900 READ DMA EXT Error 2630 [1] occurred at disk power-on lifetime: 22173 hours (923 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 25 00 00 09 ef ae 13 49 00 Error: UNC 37 sectors at LBA = 0x09efae13 = 166702611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 28 00 00 09 ef ae 10 40 00 01:21:21.200 READ DMA EXT 25 00 00 00 40 00 00 00 c2 0b 70 40 00 01:21:21.200 READ DMA EXT 25 00 00 00 08 00 00 09 ef ae 10 40 00 01:21:16.900 READ DMA EXT 25 00 00 00 08 00 00 09 ef ae 30 40 00 01:21:16.900 READ DMA EXT 25 00 00 00 02 00 00 09 b8 80 2a 40 00 01:21:16.900 READ DMA EXT Error 2629 [0] occurred at disk power-on lifetime: 22173 hours (923 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 09 ef ae 13 49 00 Error: UNC 5 sectors at LBA = 0x09efae13 = 166702611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 09 ef ae 10 40 00 01:21:16.900 READ DMA EXT 25 00 00 00 08 00 00 09 ef ae 30 40 00 01:21:16.900 READ DMA EXT 25 00 00 00 02 00 00 09 b8 80 2a 40 00 01:21:16.900 READ DMA EXT 25 00 00 00 02 00 00 09 b8 80 20 40 00 01:21:16.900 READ DMA EXT 25 00 00 00 02 00 00 09 b8 88 1e 40 00 01:21:16.900 READ DMA EXT Error 2628 [3] occurred at disk power-on lifetime: 22173 hours (923 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 09 ef ae 13 49 00 Error: UNC 5 sectors at LBA = 0x09efae13 = 166702611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 09 ef ae 10 40 00 01:21:12.200 READ DMA EXT 25 00 00 00 08 00 00 09 ef ae 10 40 00 01:21:07.900 READ DMA EXT 25 00 00 00 08 00 00 09 ef ae 30 40 00 01:21:07.900 READ DMA EXT 25 00 00 00 08 00 00 09 bf 69 c0 40 00 01:21:07.900 READ DMA EXT 25 00 00 00 01 00 00 09 f0 bd 20 40 00 01:21:07.900 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 20691 - # 2 Short offline Completed without error 00% 18530 - # 3 Short offline Completed without error 00% 18310 - # 4 Short offline Completed without error 00% 18297 - # 5 Extended offline Completed without error 00% 17875 - # 6 Short offline Completed without error 00% 16291 - # 7 Short offline Completed without error 00% 16283 - # 8 Short offline Completed without error 00% 16278 - # 9 Short offline Interrupted (host reset) 00% 16264 - #10 Short offline Completed without error 00% 16263 - #11 Extended offline Completed without error 00% 16136 - #12 Short offline Completed without error 00% 16077 - #13 Short offline Completed without error 00% 16063 - #14 Short offline Completed without error 00% 16056 - #15 Short offline Completed without error 00% 16035 - #16 Short offline Completed without error 00% 16031 - #17 Short offline Completed: read failure 10% 15993 28822 #18 Short offline Completed: read failure 30% 15977 28822 2 of 2 failed self-tests are outdated by newer successful extended offline self-test # 5 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 33/33 Celsius Lifetime Min/Max Temperature: 2/49 Celsius Specified Max Operating Temperature: 34 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2023-09-02 16:45 33 ************** ... ..( 79 skipped). .. ************** 127 2023-09-02 18:05 33 ************** 0 2023-09-02 18:06 34 *************** 1 2023-09-02 18:07 33 ************** ... ..( 7 skipped). .. ************** 9 2023-09-02 18:15 33 ************** 10 2023-09-02 18:16 34 *************** ... ..( 21 skipped). .. *************** 32 2023-09-02 18:38 34 *************** 33 2023-09-02 18:39 33 ************** 34 2023-09-02 18:40 34 *************** 35 2023-09-02 18:41 33 ************** 36 2023-09-02 18:42 33 ************** 37 2023-09-02 18:43 33 ************** 38 2023-09-02 18:44 ? - 39 2023-09-02 18:45 33 ************** ... ..( 6 skipped). .. ************** 46 2023-09-02 18:52 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS