/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.0-63.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint T166 Device Model: SAMSUNG HD403LJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: CT100-13 User Capacity: 400,087,375,360 bytes [400 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Tue May 20 20:12:37 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7362) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 125) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 098 051 - 6 3 Spin_Up_Time POS--- 100 100 015 - 7616 4 Start_Stop_Count -O--CK 086 086 000 - 14701 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 1 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 20897 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 7044 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 7756243 187 Reported_Uncorrect -O--CK 001 001 000 - 7931228 188 Command_Timeout -O--CK 098 098 000 - 285 190 Airflow_Temperature_Cel -O---K 064 053 000 - 36 194 Temperature_Celsius -O---K 127 091 000 - 37 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 7756243 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Total_Pending_Sectors -O--C- 095 093 000 - 55 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x01) instead Device Error Count: 12681 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12681 [0] occurred at disk power-on lifetime: 20725 hours (863 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 19 00 00 05 7d bb 8f e0 00 Error: UNC 25 sectors at LBA = 0x057dbb8f = 92126095 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 19 00 00 05 7d bb 8f e0 00 04:14:54.375 READ DMA EXT 25 00 00 00 08 00 00 04 b0 c5 2f e0 00 04:14:48.625 READ DMA EXT 35 00 00 00 08 00 00 02 d2 f0 97 e0 00 04:14:48.625 WRITE DMA EXT 35 00 00 00 08 00 00 00 5b fc 87 e0 00 04:14:48.625 WRITE DMA EXT 25 00 00 00 10 00 00 00 0f b4 17 e0 00 04:14:48.625 READ DMA EXT Error 12680 [7] occurred at disk power-on lifetime: 20725 hours (863 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 21 00 00 05 7d bb 87 e0 00 Error: UNC 33 sectors at LBA = 0x057dbb87 = 92126087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 21 00 00 05 7d bb 87 e0 00 04:14:48.375 READ DMA EXT 25 00 00 00 c4 00 00 04 5b 3f 0f e0 00 04:14:42.625 READ DMA EXT 35 00 00 00 08 00 00 02 d2 f5 47 e0 00 04:14:42.625 WRITE DMA EXT 25 00 00 00 08 00 00 00 d1 53 67 e0 00 04:14:42.625 READ DMA EXT 35 00 00 00 08 00 00 00 5b d9 67 e0 00 04:14:42.625 WRITE DMA EXT Error 12679 [6] occurred at disk power-on lifetime: 20725 hours (863 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 28 00 00 05 7d bb 77 e0 00 Error: UNC 40 sectors at LBA = 0x057dbb77 = 92126071 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 28 00 00 05 7d bb 77 e0 00 04:14:42.438 READ DMA EXT 25 00 00 00 08 00 00 04 5b 3f 07 e0 00 04:14:36.000 READ DMA EXT 35 00 00 00 08 00 00 00 5b d9 77 e0 00 04:14:36.000 WRITE DMA EXT 25 00 00 00 10 00 00 00 37 02 a8 e0 00 04:14:36.000 READ DMA EXT 35 00 00 00 01 00 00 00 11 34 7f e0 00 04:14:36.000 WRITE DMA EXT Error 12678 [5] occurred at disk power-on lifetime: 20725 hours (863 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 28 00 00 05 7d bb 77 e0 00 Error: UNC 40 sectors at LBA = 0x057dbb77 = 92126071 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 28 00 00 05 7d bb 77 e0 00 04:14:34.563 READ DMA EXT 35 00 00 00 08 00 00 00 5b fc 7f e0 00 04:14:27.188 WRITE DMA EXT 25 00 00 00 80 00 00 16 c9 d4 41 e0 00 04:14:27.188 READ DMA EXT 35 00 00 00 08 00 00 0a 05 f4 7f e0 00 04:14:27.188 WRITE DMA EXT 25 00 00 00 08 00 00 07 9b 8e 87 e0 00 04:14:27.188 READ DMA EXT Error 12677 [4] occurred at disk power-on lifetime: 20725 hours (863 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 b1 00 00 05 7d ba f7 e0 00 Error: UNC 177 sectors at LBA = 0x057dbaf7 = 92125943 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 b1 00 00 05 7d ba f7 e0 00 04:14:27.063 READ DMA EXT 35 00 00 00 10 00 00 03 8d c3 8f e0 00 04:14:20.625 WRITE DMA EXT 25 00 00 00 08 00 00 03 65 4f ef e0 00 04:14:20.625 READ DMA EXT 35 00 00 00 10 00 00 00 e4 65 df e0 00 04:14:20.625 WRITE DMA EXT 35 00 00 00 08 00 00 00 00 7e 07 e0 00 04:14:20.625 WRITE DMA EXT Error 12676 [3] occurred at disk power-on lifetime: 20725 hours (863 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 b1 00 00 05 7d ba f7 e0 00 Error: UNC 177 sectors at LBA = 0x057dbaf7 = 92125943 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 b1 00 00 05 7d ba f7 e0 00 04:14:20.500 READ DMA EXT 25 00 00 00 08 00 00 05 7d ba ef e0 00 04:14:13.313 READ DMA EXT 25 00 00 00 18 00 00 05 43 5a cf e0 00 04:14:13.313 READ DMA EXT 25 00 00 00 b9 00 00 04 97 93 df e0 00 04:14:13.313 READ DMA EXT 25 00 00 00 08 00 00 05 43 5a c7 e0 00 04:14:13.250 READ DMA EXT Error 12675 [2] occurred at disk power-on lifetime: 20711 hours (862 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 00 01 2a 5f e0 00 Error: ICRC, ABRT 128 sectors at LBA = 0x00012a5f = 76383 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 00 01 2a 5f e0 00 00:06:18.625 WRITE DMA EXT 35 00 00 00 08 00 00 00 5b d9 7f e0 00 00:06:18.625 WRITE DMA EXT 35 00 00 00 14 00 00 00 0f 9f 28 e0 00 00:06:18.625 WRITE DMA EXT 35 00 00 01 00 00 00 00 0f 9e 28 e0 00 00:06:18.625 WRITE DMA EXT 35 00 00 01 00 00 00 00 0f 9d 28 e0 00 00:06:18.625 WRITE DMA EXT Error 12674 [1] occurred at disk power-on lifetime: 20601 hours (858 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 13 51 23 97 e0 00 Error: ICRC, ABRT 256 sectors at LBA = 0x13512397 = 324084631 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 01 00 00 00 13 51 23 97 e0 00 00:04:49.813 WRITE DMA EXT 25 00 00 00 08 00 00 0d 42 0d 27 e0 00 00:04:49.813 READ DMA EXT 25 00 00 00 08 00 00 0d 3f c1 7f e0 00 00:04:49.813 READ DMA EXT 35 00 00 00 08 00 00 02 a7 db 5d e0 00 00:04:49.750 WRITE DMA EXT 25 00 00 00 08 00 00 02 1c 5e 4f e0 00 00:04:49.750 READ DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 20/36 Celsius Lifetime Min/Max Temperature: 8/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (116) Index Estimated Time Temperature Celsius 117 2025-05-20 18:05 36 ***************** ... ..( 25 skipped). .. ***************** 15 2025-05-20 18:31 36 ***************** 16 2025-05-20 18:32 37 ****************** 17 2025-05-20 18:33 37 ****************** 18 2025-05-20 18:34 36 ***************** ... ..( 4 skipped). .. ***************** 23 2025-05-20 18:39 36 ***************** 24 2025-05-20 18:40 37 ****************** ... ..( 2 skipped). .. ****************** 27 2025-05-20 18:43 37 ****************** 28 2025-05-20 18:44 28 ********* 29 2025-05-20 18:45 30 *********** 30 2025-05-20 18:46 28 ********* 31 2025-05-20 18:47 20 * 32 2025-05-20 18:48 20 * 33 2025-05-20 18:49 21 ** 34 2025-05-20 18:50 22 *** 35 2025-05-20 18:51 26 ******* ... ..( 2 skipped). .. ******* 38 2025-05-20 18:54 26 ******* 39 2025-05-20 18:55 28 ********* 40 2025-05-20 18:56 29 ********** ... ..( 2 skipped). .. ********** 43 2025-05-20 18:59 29 ********** 44 2025-05-20 19:00 30 *********** ... ..( 3 skipped). .. *********** 48 2025-05-20 19:04 30 *********** 49 2025-05-20 19:05 31 ************ ... ..( 5 skipped). .. ************ 55 2025-05-20 19:11 31 ************ 56 2025-05-20 19:12 32 ************* ... ..( 5 skipped). .. ************* 62 2025-05-20 19:18 32 ************* 63 2025-05-20 19:19 33 ************** ... ..( 6 skipped). .. ************** 70 2025-05-20 19:26 33 ************** 71 2025-05-20 19:27 35 **************** ... ..( 19 skipped). .. **************** 91 2025-05-20 19:47 35 **************** 92 2025-05-20 19:48 36 ***************** ... ..( 23 skipped). .. ***************** 116 2025-05-20 20:12 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.0-63.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST3500320AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SD1A User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue May 20 20:12:38 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 650) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 117) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 116 099 006 - 108389592 3 Spin_Up_Time PO---- 094 094 000 - 0 4 Start_Stop_Count -O--CK 095 095 020 - 5433 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 19 7 Seek_Error_Rate POSR-- 072 060 030 - 94885176088 9 Power_On_Hours -O--CK 088 088 000 - 10782 10 Spin_Retry_Count PO--C- 100 100 097 - 47 12 Power_Cycle_Count -O--CK 095 095 020 - 5320 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 085 085 000 - 15 188 Command_Timeout -O--CK 100 095 000 - 30065428027 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 054 045 - 37 (Min/Max 21/37) 194 Temperature_Celsius -O---K 037 046 000 - 37 (0 8 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 030 022 000 - 108389592 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 197 000 - 124 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 15 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 15 [14] occurred at disk power-on lifetime: 5184 hours (216 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 28 00 61 01 00 00 Error: UNC at LBA = 0x28006101 = 671113473 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 28 00 61 00 e0 00 00:00:51.506 READ DMA EXT 25 00 00 00 08 00 00 28 00 61 00 e0 00 00:00:43.813 READ DMA EXT 25 00 00 00 08 00 00 28 00 61 08 e0 00 00:00:43.806 READ DMA EXT 25 00 00 00 08 00 00 27 00 61 f8 e0 00 00:00:43.805 READ DMA EXT 25 00 00 00 08 00 00 27 00 61 f0 e0 00 00:00:43.744 READ DMA EXT Error 14 [13] occurred at disk power-on lifetime: 5184 hours (216 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 28 00 61 01 00 00 Error: UNC at LBA = 0x28006101 = 671113473 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 28 00 61 00 e0 00 00:00:43.813 READ DMA EXT 25 00 00 00 08 00 00 28 00 61 08 e0 00 00:00:43.806 READ DMA EXT 25 00 00 00 08 00 00 27 00 61 f8 e0 00 00:00:43.805 READ DMA EXT 25 00 00 00 08 00 00 27 00 61 f0 e0 00 00:00:43.744 READ DMA EXT 25 00 00 00 80 00 04 68 00 47 60 e0 00 00:00:43.668 READ DMA EXT Error 13 [12] occurred at disk power-on lifetime: 5184 hours (216 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 28 00 61 01 00 00 Error: UNC at LBA = 0x28006101 = 671113473 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 27 00 61 f0 e0 00 00:00:35.854 READ DMA EXT 25 00 00 00 08 00 04 58 00 47 48 e0 00 00:00:35.845 READ DMA EXT 25 00 00 00 08 00 04 57 00 47 f8 e0 00 00:00:35.826 READ DMA EXT 25 00 00 00 80 00 04 53 00 a6 40 e0 00 00:00:35.824 READ DMA EXT 25 00 00 00 80 00 04 52 00 a6 c0 e0 00 00:00:35.808 READ DMA EXT Error 12 [11] occurred at disk power-on lifetime: 2816 hours (117 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 1a 63 00 df 0f 00 00 Error: UNC at LBA = 0x1a6300df0f = 113330151183 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 1a 63 00 df 0f e0 00 00:30:23.208 READ DMA EXT 35 00 00 00 18 00 00 d8 00 5e 78 e0 00 00:30:23.207 WRITE DMA EXT 35 00 00 01 00 00 00 d7 00 5e 78 e0 00 00:30:23.206 WRITE DMA EXT 35 00 00 00 10 00 00 e8 00 3a c0 e0 00 00:30:23.206 WRITE DMA EXT 25 00 00 00 01 00 1a 63 00 df 0e e0 00 00:30:23.205 READ DMA EXT Error 11 [10] occurred at disk power-on lifetime: 2816 hours (117 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 1a 63 00 df 0f 00 00 Error: UNC at LBA = 0x1a6300df0f = 113330151183 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 1a 63 00 df 00 e0 00 00:30:19.260 READ DMA EXT 35 00 00 00 10 00 1a 71 00 ee 80 e0 00 00:30:19.259 WRITE DMA EXT 35 00 00 00 c0 00 1a c0 00 c3 a0 e0 00 00:30:19.257 WRITE DMA EXT 35 00 00 01 00 00 1a bf 00 c3 a0 e0 00 00:30:19.256 WRITE DMA EXT 35 00 00 01 00 00 1a be 00 c3 a0 e0 00 00:30:19.255 WRITE DMA EXT Error 10 [9] occurred at disk power-on lifetime: 2634 hours (109 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 1a 63 00 df 0f 00 00 Error: UNC at LBA = 0x1a6300df0f = 113330151183 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 01 00 1a 63 00 df 0f e0 00 01:08:22.131 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 34 68 00 12 00 e0 00 01:08:22.130 READ DMA EXT 42 da d8 00 01 00 1a 63 00 df 0e e0 00 01:08:22.080 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 01:08:21.996 READ DMA EXT 42 da d8 00 02 00 1a 63 00 df 0e e0 00 01:08:17.167 READ VERIFY SECTOR(S) EXT Error 9 [8] occurred at disk power-on lifetime: 2634 hours (109 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 1a 63 00 df 0f 00 00 Error: UNC at LBA = 0x1a6300df0f = 113330151183 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 02 00 1a 63 00 df 0e e0 00 01:08:17.167 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 01:08:17.165 READ DMA EXT 42 da d8 00 02 00 1a 63 00 df 0c e0 00 01:08:17.115 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 01:08:17.027 READ DMA EXT 42 da d8 00 04 00 1a 63 00 df 0c e0 00 01:08:12.219 READ VERIFY SECTOR(S) EXT Error 8 [7] occurred at disk power-on lifetime: 2634 hours (109 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 1a 63 00 df 0f 00 00 Error: UNC at LBA = 0x1a6300df0f = 113330151183 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 04 00 1a 63 00 df 0c e0 00 01:08:12.219 READ VERIFY SECTOR(S) EXT 42 da d8 00 04 00 1a 63 00 df 08 e0 00 01:08:12.176 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 34 68 00 12 00 e0 00 01:08:12.099 READ DMA EXT 42 da d8 00 08 00 1a 63 00 df 08 e0 00 01:08:07.164 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 01:08:07.162 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 21/37 Celsius Lifetime Min/Max Temperature: 8/46 Celsius Under/Over Temperature Limit Count: 0/86 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (25) Index Estimated Time Temperature Celsius 26 2025-05-20 18:05 37 ****************** ... ..( 13 skipped). .. ****************** 40 2025-05-20 18:19 37 ****************** 41 2025-05-20 18:20 38 ******************* ... ..( 2 skipped). .. ******************* 44 2025-05-20 18:23 38 ******************* 45 2025-05-20 18:24 37 ****************** ... ..( 19 skipped). .. ****************** 65 2025-05-20 18:44 37 ****************** 66 2025-05-20 18:45 32 ************* 67 2025-05-20 18:46 ? - 68 2025-05-20 18:47 21 ** 69 2025-05-20 18:48 22 *** 70 2025-05-20 18:49 23 **** 71 2025-05-20 18:50 24 ***** 72 2025-05-20 18:51 25 ****** 73 2025-05-20 18:52 25 ****** 74 2025-05-20 18:53 26 ******* 75 2025-05-20 18:54 27 ******** 76 2025-05-20 18:55 27 ******** 77 2025-05-20 18:56 28 ********* 78 2025-05-20 18:57 28 ********* 79 2025-05-20 18:58 29 ********** 80 2025-05-20 18:59 29 ********** 81 2025-05-20 19:00 30 *********** 82 2025-05-20 19:01 30 *********** 83 2025-05-20 19:02 31 ************ 84 2025-05-20 19:03 31 ************ 85 2025-05-20 19:04 31 ************ 86 2025-05-20 19:05 32 ************* 87 2025-05-20 19:06 32 ************* 88 2025-05-20 19:07 33 ************** ... ..( 3 skipped). .. ************** 92 2025-05-20 19:11 33 ************** 93 2025-05-20 19:12 34 *************** ... ..( 3 skipped). .. *************** 97 2025-05-20 19:16 34 *************** 98 2025-05-20 19:17 35 **************** ... ..( 9 skipped). .. **************** 108 2025-05-20 19:27 35 **************** 109 2025-05-20 19:28 36 ***************** ... ..( 19 skipped). .. ***************** 1 2025-05-20 19:48 36 ***************** 2 2025-05-20 19:49 37 ****************** ... ..( 22 skipped). .. ****************** 25 2025-05-20 20:12 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.0-63.fc42.x86_64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8U (USB) Device Model: ST1000LM025 HN-M101ABB Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2BA30001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue May 20 20:12:38 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13500) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 225) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 089 089 025 - 3594 4 Start_Stop_Count -O--CK 095 095 000 - 5192 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 641 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 19 12 Power_Cycle_Count -O--CK 090 090 000 - 10333 191 G-Sense_Error_Rate -O---K 100 100 000 - 5 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 062 000 - 33 (Min/Max 17/47) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 168 223 Load_Retry_Count -O--CK 100 100 000 - 19 225 Load_Cycle_Count -O--CK 098 098 000 - 25105 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 24/36 Celsius Lifetime Min/Max Temperature: 18/46 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2025-05-20 09:35 33 ************** 20 2025-05-20 09:40 38 ******************* 21 2025-05-20 09:45 37 ****************** ... ..( 2 skipped). .. ****************** 24 2025-05-20 10:00 37 ****************** 25 2025-05-20 10:05 36 ***************** 26 2025-05-20 10:10 35 **************** 27 2025-05-20 10:15 29 ********** 28 2025-05-20 10:20 31 ************ 29 2025-05-20 10:25 31 ************ 30 2025-05-20 10:30 32 ************* 31 2025-05-20 10:35 33 ************** 32 2025-05-20 10:40 33 ************** 33 2025-05-20 10:45 33 ************** 34 2025-05-20 10:50 32 ************* 35 2025-05-20 10:55 33 ************** 36 2025-05-20 11:00 33 ************** 37 2025-05-20 11:05 34 *************** 38 2025-05-20 11:10 33 ************** 39 2025-05-20 11:15 32 ************* 40 2025-05-20 11:20 32 ************* 41 2025-05-20 11:25 32 ************* 42 2025-05-20 11:30 33 ************** 43 2025-05-20 11:35 34 *************** 44 2025-05-20 11:40 34 *************** 45 2025-05-20 11:45 33 ************** 46 2025-05-20 11:50 32 ************* 47 2025-05-20 11:55 32 ************* 48 2025-05-20 12:00 30 *********** 49 2025-05-20 12:05 32 ************* 50 2025-05-20 12:10 30 *********** 51 2025-05-20 12:15 31 ************ 52 2025-05-20 12:20 32 ************* 53 2025-05-20 12:25 32 ************* 54 2025-05-20 12:30 33 ************** 55 2025-05-20 12:35 34 *************** 56 2025-05-20 12:40 37 ****************** 57 2025-05-20 12:45 26 ******* 58 2025-05-20 12:50 27 ******** 59 2025-05-20 12:55 30 *********** 60 2025-05-20 13:00 32 ************* 61 2025-05-20 13:05 34 *************** 62 2025-05-20 13:10 36 ***************** 63 2025-05-20 13:15 36 ***************** 64 2025-05-20 13:20 36 ***************** 65 2025-05-20 13:25 35 **************** ... ..( 2 skipped). .. **************** 68 2025-05-20 13:40 35 **************** 69 2025-05-20 13:45 34 *************** 70 2025-05-20 13:50 34 *************** 71 2025-05-20 13:55 35 **************** 72 2025-05-20 14:00 35 **************** 73 2025-05-20 14:05 36 ***************** 74 2025-05-20 14:10 37 ****************** 75 2025-05-20 14:15 36 ***************** 76 2025-05-20 14:20 36 ***************** 77 2025-05-20 14:25 36 ***************** 78 2025-05-20 14:30 35 **************** 79 2025-05-20 14:35 35 **************** 80 2025-05-20 14:40 36 ***************** 81 2025-05-20 14:45 37 ****************** 82 2025-05-20 14:50 36 ***************** 83 2025-05-20 14:55 35 **************** 84 2025-05-20 15:00 34 *************** 85 2025-05-20 15:05 33 ************** 86 2025-05-20 15:10 33 ************** 87 2025-05-20 15:15 33 ************** 88 2025-05-20 15:20 32 ************* 89 2025-05-20 15:25 27 ******** 90 2025-05-20 15:30 31 ************ 91 2025-05-20 15:35 28 ********* 92 2025-05-20 15:40 29 ********** 93 2025-05-20 15:45 31 ************ 94 2025-05-20 15:50 33 ************** 95 2025-05-20 15:55 35 **************** 96 2025-05-20 16:00 37 ****************** 97 2025-05-20 16:05 37 ****************** 98 2025-05-20 16:10 37 ****************** 99 2025-05-20 16:15 36 ***************** 100 2025-05-20 16:20 36 ***************** 101 2025-05-20 16:25 37 ****************** 102 2025-05-20 16:30 37 ****************** 103 2025-05-20 16:35 37 ****************** 104 2025-05-20 16:40 36 ***************** 105 2025-05-20 16:45 35 **************** 106 2025-05-20 16:50 33 ************** 107 2025-05-20 16:55 29 ********** 108 2025-05-20 17:00 30 *********** 109 2025-05-20 17:05 33 ************** 110 2025-05-20 17:10 34 *************** 111 2025-05-20 17:15 33 ************** 112 2025-05-20 17:20 34 *************** 113 2025-05-20 17:25 36 ***************** 114 2025-05-20 17:30 37 ****************** 115 2025-05-20 17:35 35 **************** 116 2025-05-20 17:40 35 **************** 117 2025-05-20 17:45 35 **************** 118 2025-05-20 17:50 36 ***************** 119 2025-05-20 17:55 32 ************* 120 2025-05-20 18:00 33 ************** 121 2025-05-20 18:05 35 **************** 122 2025-05-20 18:10 33 ************** 123 2025-05-20 18:15 34 *************** 124 2025-05-20 18:20 28 ********* 125 2025-05-20 18:25 30 *********** 126 2025-05-20 18:30 32 ************* 127 2025-05-20 18:35 34 *************** 0 2025-05-20 18:40 35 **************** 1 2025-05-20 18:45 35 **************** 2 2025-05-20 18:50 36 ***************** 3 2025-05-20 18:55 36 ***************** 4 2025-05-20 19:00 36 ***************** 5 2025-05-20 19:05 31 ************ 6 2025-05-20 19:10 32 ************* 7 2025-05-20 19:15 32 ************* 8 2025-05-20 19:20 32 ************* 9 2025-05-20 19:25 24 ***** 10 2025-05-20 19:30 30 *********** 11 2025-05-20 19:35 30 *********** 12 2025-05-20 19:40 31 ************ 13 2025-05-20 19:45 32 ************* 14 2025-05-20 19:50 26 ******* 15 2025-05-20 19:55 28 ********* 16 2025-05-20 20:00 30 *********** 17 2025-05-20 20:05 32 ************* 18 2025-05-20 20:10 33 ************** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 2 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 2 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 59 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 58 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 2 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 2 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 2 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 2345 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 134 Vendor specific 0x8e08 4 3 Vendor specific 0x8e09 4 1343 Vendor specific 0x8e0a 4 1680 Vendor specific 0x8e0b 4 50176 Vendor specific 0x8e0c 4 1348 Vendor specific 0x8e0d 4 1341 Vendor specific 0x8e0e 4 336 Vendor specific 0x8e0f 4 2748547 Vendor specific 0x8e10 4 1350 Vendor specific 0x8e11 4 2 Vendor specific