/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Mobile Device Model: WDC WD5000LPVX-22V0TT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Sep 25 11:16:00 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 248) Self-test routine in progress... 80% of test remaining. Total time to complete Offline data collection: ( 9660) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 111) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 5 3 Spin_Up_Time POS--K 153 145 021 - 1325 4 Start_Stop_Count -O--CK 092 092 000 - 8946 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 099 099 000 - 1230 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 637 191 G-Sense_Error_Rate -O--CK 090 090 000 - 10 192 Power-Off_Retract_Count -O--CK 200 200 000 - 63 193 Load_Cycle_Count -O--CK 195 195 000 - 15497 194 Temperature_Celsius -O---K 103 092 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 78 e9 e8 40 00 Error: UNC at LBA = 0x0078e9e8 = 7924200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 3d 00 20 00 00 00 78 e9 d9 40 00 00:00:27.631 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:26.694 SET FEATURES [Enable write cache] 60 00 3d 00 18 00 00 00 78 e9 d9 40 00 00:00:23.182 READ FPDMA QUEUED 61 00 08 00 10 00 00 00 19 e9 60 40 00 00:00:22.761 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:22.761 FLUSH CACHE EXT Error 4 [3] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 78 e9 e8 40 00 Error: UNC at LBA = 0x0078e9e8 = 7924200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 3d 00 18 00 00 00 78 e9 d9 40 00 00:00:23.182 READ FPDMA QUEUED 61 00 08 00 10 00 00 00 19 e9 60 40 00 00:00:22.761 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:22.761 FLUSH CACHE EXT ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:22.214 SET FEATURES [Enable write cache] 60 00 3d 00 f8 00 00 00 78 e9 d9 40 00 00:00:18.687 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 78 e9 e8 40 00 Error: UNC at LBA = 0x0078e9e8 = 7924200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 3d 00 f8 00 00 00 78 e9 d9 40 00 00:00:18.687 READ FPDMA QUEUED 61 00 08 00 f0 00 00 00 75 77 90 40 00 00:00:17.761 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 00 00:00:17.720 FLUSH CACHE EXT 61 00 08 00 e0 00 00 00 75 77 98 40 00 00:00:17.720 WRITE FPDMA QUEUED 61 00 08 00 d8 00 00 00 75 8e f0 40 00 00:00:17.719 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 78 e9 e8 40 00 Error: UNC at LBA = 0x0078e9e8 = 7924200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 3d 00 d0 00 00 00 78 e9 d9 40 00 00:00:14.175 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:13.270 SET FEATURES [Enable write cache] 60 00 3d 00 c8 00 00 00 78 e9 d9 40 00 00:00:09.710 READ FPDMA QUEUED 60 00 3d 00 c0 00 00 00 78 e9 9c 40 00 00:00:09.709 READ FPDMA QUEUED 60 00 02 00 b8 00 00 00 78 e9 9a 40 00 00:00:09.709 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 78 e9 e8 40 00 Error: UNC at LBA = 0x0078e9e8 = 7924200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 3d 00 c8 00 00 00 78 e9 d9 40 00 00:00:09.710 READ FPDMA QUEUED 60 00 3d 00 c0 00 00 00 78 e9 9c 40 00 00:00:09.709 READ FPDMA QUEUED 60 00 02 00 b8 00 00 00 78 e9 9a 40 00 00:00:09.709 READ FPDMA QUEUED 60 00 02 00 b0 00 00 00 78 e9 98 40 00 00:00:09.699 READ FPDMA QUEUED 60 00 08 00 a8 00 00 00 79 e8 40 40 00 00:00:09.698 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: DST executing in background (3) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 21/40 Celsius Lifetime Min/Max Temperature: 16/50 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (116) Index Estimated Time Temperature Celsius 117 2016-09-25 09:09 31 ************ 118 2016-09-25 09:10 ? - 119 2016-09-25 09:11 31 ************ 120 2016-09-25 09:12 31 ************ 121 2016-09-25 09:13 ? - 122 2016-09-25 09:14 31 ************ 123 2016-09-25 09:15 31 ************ 124 2016-09-25 09:16 ? - 125 2016-09-25 09:17 31 ************ 126 2016-09-25 09:18 32 ************* 127 2016-09-25 09:19 ? - 0 2016-09-25 09:20 32 ************* 1 2016-09-25 09:21 ? - 2 2016-09-25 09:22 32 ************* 3 2016-09-25 09:23 32 ************* 4 2016-09-25 09:24 ? - 5 2016-09-25 09:25 32 ************* 6 2016-09-25 09:26 32 ************* 7 2016-09-25 09:27 ? - 8 2016-09-25 09:28 32 ************* 9 2016-09-25 09:29 ? - 10 2016-09-25 09:30 32 ************* 11 2016-09-25 09:31 32 ************* 12 2016-09-25 09:32 ? - 13 2016-09-25 09:33 32 ************* 14 2016-09-25 09:34 32 ************* 15 2016-09-25 09:35 ? - 16 2016-09-25 09:36 32 ************* 17 2016-09-25 09:37 32 ************* 18 2016-09-25 09:38 ? - 19 2016-09-25 09:39 31 ************ ... ..( 2 skipped). .. ************ 22 2016-09-25 09:42 31 ************ 23 2016-09-25 09:43 ? - 24 2016-09-25 09:44 31 ************ 25 2016-09-25 09:45 32 ************* 26 2016-09-25 09:46 ? - 27 2016-09-25 09:47 32 ************* 28 2016-09-25 09:48 32 ************* 29 2016-09-25 09:49 32 ************* 30 2016-09-25 09:50 ? - 31 2016-09-25 09:51 32 ************* 32 2016-09-25 09:52 ? - 33 2016-09-25 09:53 32 ************* 34 2016-09-25 09:54 32 ************* 35 2016-09-25 09:55 ? - 36 2016-09-25 09:56 32 ************* 37 2016-09-25 09:57 32 ************* 38 2016-09-25 09:58 ? - 39 2016-09-25 09:59 32 ************* 40 2016-09-25 10:00 ? - 41 2016-09-25 10:01 32 ************* 42 2016-09-25 10:02 32 ************* 43 2016-09-25 10:03 33 ************** 44 2016-09-25 10:04 ? - 45 2016-09-25 10:05 33 ************** 46 2016-09-25 10:06 33 ************** 47 2016-09-25 10:07 ? - 48 2016-09-25 10:08 33 ************** 49 2016-09-25 10:09 ? - 50 2016-09-25 10:10 25 ****** 51 2016-09-25 10:11 ? - 52 2016-09-25 10:12 25 ****** 53 2016-09-25 10:13 ? - 54 2016-09-25 10:14 21 ** 55 2016-09-25 10:15 22 *** 56 2016-09-25 10:16 23 **** 57 2016-09-25 10:17 ? - 58 2016-09-25 10:18 23 **** 59 2016-09-25 10:19 24 ***** 60 2016-09-25 10:20 ? - 61 2016-09-25 10:21 24 ***** 62 2016-09-25 10:22 24 ***** 63 2016-09-25 10:23 25 ****** 64 2016-09-25 10:24 ? - 65 2016-09-25 10:25 25 ****** 66 2016-09-25 10:26 25 ****** 67 2016-09-25 10:27 ? - 68 2016-09-25 10:28 25 ****** 69 2016-09-25 10:29 26 ******* 70 2016-09-25 10:30 27 ******** 71 2016-09-25 10:31 27 ******** 72 2016-09-25 10:32 ? - 73 2016-09-25 10:33 27 ******** 74 2016-09-25 10:34 27 ******** 75 2016-09-25 10:35 27 ******** 76 2016-09-25 10:36 ? - 77 2016-09-25 10:37 27 ******** 78 2016-09-25 10:38 27 ******** 79 2016-09-25 10:39 27 ******** 80 2016-09-25 10:40 ? - 81 2016-09-25 10:41 27 ******** 82 2016-09-25 10:42 ? - 83 2016-09-25 10:43 28 ********* ... ..( 3 skipped). .. ********* 87 2016-09-25 10:47 28 ********* 88 2016-09-25 10:48 ? - 89 2016-09-25 10:49 28 ********* ... ..( 2 skipped). .. ********* 92 2016-09-25 10:52 28 ********* 93 2016-09-25 10:53 29 ********** 94 2016-09-25 10:54 29 ********** 95 2016-09-25 10:55 30 *********** 96 2016-09-25 10:56 30 *********** 97 2016-09-25 10:57 31 ************ 98 2016-09-25 10:58 32 ************* 99 2016-09-25 10:59 33 ************** 100 2016-09-25 11:00 34 *************** 101 2016-09-25 11:01 35 **************** ... ..( 2 skipped). .. **************** 104 2016-09-25 11:04 35 **************** 105 2016-09-25 11:05 36 ***************** 106 2016-09-25 11:06 37 ****************** 107 2016-09-25 11:07 37 ****************** 108 2016-09-25 11:08 38 ******************* 109 2016-09-25 11:09 38 ******************* 110 2016-09-25 11:10 38 ******************* 111 2016-09-25 11:11 39 ******************** 112 2016-09-25 11:12 39 ******************** 113 2016-09-25 11:13 40 ********************* ... ..( 2 skipped). .. ********************* 116 2016-09-25 11:16 40 ********************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2683 Vendor specific