/dev/sda smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.0-63.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 860 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: RVT04B6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.5/5706 ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Sep 1 19:19:41 2025 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 5019 12 Power_Cycle_Count -O--CK 099 099 000 - 466 177 Wear_Leveling_Count PO--C- 098 098 000 - 22 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 070 053 000 - 30 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 095 095 000 - 4137 235 POR_Recovery_Count -O--C- 099 099 000 - 111 241 Total_LBAs_Written -O--CK 099 099 000 - 19506771185 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 4630 - # 2 Short offline Completed without error 00% 4625 - # 3 Extended offline Completed without error 00% 4416 - # 4 Extended offline Interrupted (host reset) 80% 7 - # 5 Extended offline Interrupted (host reset) 80% 6 - # 6 Short offline Completed without error 00% 6 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 26/40 Celsius Lifetime Min/Max Temperature: 20/47 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2025-08-31 22:00 29 ********** ... ..( 10 skipped). .. ********** 126 2025-08-31 23:50 29 ********** 127 2025-09-01 00:00 28 ********* 0 2025-09-01 00:10 28 ********* 1 2025-09-01 00:20 27 ******** ... ..( 20 skipped). .. ******** 22 2025-09-01 03:50 27 ******** 23 2025-09-01 04:00 26 ******* 24 2025-09-01 04:10 26 ******* 25 2025-09-01 04:20 27 ******** 26 2025-09-01 04:30 27 ******** 27 2025-09-01 04:40 26 ******* ... ..( 3 skipped). .. ******* 31 2025-09-01 05:20 26 ******* 32 2025-09-01 05:30 27 ******** 33 2025-09-01 05:40 26 ******* ... ..( 18 skipped). .. ******* 52 2025-09-01 08:50 26 ******* 53 2025-09-01 09:00 27 ******** 54 2025-09-01 09:10 26 ******* ... ..( 3 skipped). .. ******* 58 2025-09-01 09:50 26 ******* 59 2025-09-01 10:00 27 ******** 60 2025-09-01 10:10 26 ******* 61 2025-09-01 10:20 27 ******** 62 2025-09-01 10:30 26 ******* 63 2025-09-01 10:40 27 ******** 64 2025-09-01 10:50 27 ******** 65 2025-09-01 11:00 27 ******** 66 2025-09-01 11:10 26 ******* 67 2025-09-01 11:20 27 ******** ... ..( 11 skipped). .. ******** 79 2025-09-01 13:20 27 ******** 80 2025-09-01 13:30 26 ******* ... ..( 3 skipped). .. ******* 84 2025-09-01 14:10 26 ******* 85 2025-09-01 14:20 30 *********** 86 2025-09-01 14:30 29 ********** 87 2025-09-01 14:40 27 ******** 88 2025-09-01 14:50 28 ********* 89 2025-09-01 15:00 31 ************ 90 2025-09-01 15:10 ? - 91 2025-09-01 15:20 21 ** 92 2025-09-01 15:30 27 ******** 93 2025-09-01 15:40 30 *********** 94 2025-09-01 15:50 25 ****** 95 2025-09-01 16:00 26 ******* 96 2025-09-01 16:10 ? - 97 2025-09-01 16:20 26 ******* 98 2025-09-01 16:30 27 ******** 99 2025-09-01 16:40 27 ******** 100 2025-09-01 16:50 30 *********** 101 2025-09-01 17:00 28 ********* 102 2025-09-01 17:10 28 ********* 103 2025-09-01 17:20 31 ************ 104 2025-09-01 17:30 29 ********** 105 2025-09-01 17:40 28 ********* 106 2025-09-01 17:50 28 ********* 107 2025-09-01 18:00 28 ********* 108 2025-09-01 18:10 27 ******** 109 2025-09-01 18:20 28 ********* 110 2025-09-01 18:30 28 ********* 111 2025-09-01 18:40 27 ******** 112 2025-09-01 18:50 28 ********* 113 2025-09-01 19:00 31 ************ 114 2025-09-01 19:10 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 466 --- Lifetime Power-On Resets 0x01 0x010 4 5019 --- Power-on Hours 0x01 0x018 6 19506771185 --- Logical Sectors Written 0x01 0x020 6 302174400 --- Number of Write Commands 0x01 0x028 6 16887587778 --- Logical Sectors Read 0x01 0x030 6 166802150 --- Number of Read Commands 0x01 0x038 6 985000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 59 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 30 --- Current Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 8449 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 4137 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 11 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.0-63.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital AV-GP Device Model: WDC WD5000AVCS-632DY1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.00A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.5/5706 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Sep 1 19:19:41 2025 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 140) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 186 185 021 - 3658 4 Start_Stop_Count -O--CK 099 099 000 - 1022 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 026 026 000 - 54669 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 476 192 Power-Off_Retract_Count -O--CK 200 200 000 - 204 193 Load_Cycle_Count -O--CK 200 200 000 - 817 194 Temperature_Celsius -O---K 109 088 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 54281 - # 2 Short offline Completed without error 00% 54276 - # 3 Extended offline Completed without error 00% 54067 - # 4 Short captive Completed without error 00% 45208 - # 5 Short captive Completed without error 00% 45208 - # 6 Short captive Completed without error 00% 2 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 31/34 Celsius Lifetime Min/Max Temperature: 0/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (45) Index Estimated Time Temperature Celsius 46 2025-09-01 11:22 33 ************** ... ..(101 skipped). .. ************** 148 2025-09-01 13:04 33 ************** 149 2025-09-01 13:05 34 *************** ... ..( 5 skipped). .. *************** 155 2025-09-01 13:11 34 *************** 156 2025-09-01 13:12 33 ************** ... ..(238 skipped). .. ************** 395 2025-09-01 17:11 33 ************** 396 2025-09-01 17:12 ? - 397 2025-09-01 17:13 19 - 398 2025-09-01 17:14 19 - 399 2025-09-01 17:15 20 * 400 2025-09-01 17:16 21 ** 401 2025-09-01 17:17 21 ** 402 2025-09-01 17:18 22 *** 403 2025-09-01 17:19 22 *** 404 2025-09-01 17:20 22 *** 405 2025-09-01 17:21 23 **** 406 2025-09-01 17:22 24 ***** 407 2025-09-01 17:23 24 ***** 408 2025-09-01 17:24 25 ****** ... ..( 2 skipped). .. ****** 411 2025-09-01 17:27 25 ****** 412 2025-09-01 17:28 26 ******* ... ..( 3 skipped). .. ******* 416 2025-09-01 17:32 26 ******* 417 2025-09-01 17:33 27 ******** 418 2025-09-01 17:34 27 ******** 419 2025-09-01 17:35 28 ********* 420 2025-09-01 17:36 28 ********* 421 2025-09-01 17:37 28 ********* 422 2025-09-01 17:38 29 ********** ... ..( 5 skipped). .. ********** 428 2025-09-01 17:44 29 ********** 429 2025-09-01 17:45 30 *********** ... ..( 5 skipped). .. *********** 435 2025-09-01 17:51 30 *********** 436 2025-09-01 17:52 31 ************ ... ..( 6 skipped). .. ************ 443 2025-09-01 17:59 31 ************ 444 2025-09-01 18:00 32 ************* 445 2025-09-01 18:01 32 ************* 446 2025-09-01 18:02 32 ************* 447 2025-09-01 18:03 ? - 448 2025-09-01 18:04 32 ************* 449 2025-09-01 18:05 31 ************ 450 2025-09-01 18:06 32 ************* ... ..( 18 skipped). .. ************* 469 2025-09-01 18:25 32 ************* 470 2025-09-01 18:26 33 ************** ... ..( 52 skipped). .. ************** 45 2025-09-01 19:19 33 ************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 11247 Vendor specific /dev/sdc smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.0-63.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint T166 Device Model: SAMSUNG HD501LJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: CR100-12 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.5/5706 ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Mon Sep 1 19:19:42 2025 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 8777) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 150) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 253 100 051 - 0 3 Spin_Up_Time POS--- 100 100 015 - 7616 4 Start_Stop_Count -O--CK 098 098 000 - 2703 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 3 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 6582 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 253 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1242 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 17578 187 Reported_Uncorrect -O--CK 084 084 000 - 17 188 Command_Timeout -O--CK 001 001 000 - 29687 190 Airflow_Temperature_Cel -O---K 068 058 000 - 32 194 Temperature_Celsius -O---K 142 112 000 - 32 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 17578 196 Reallocated_Event_Count -O--CK 100 100 000 - 3 197 Total_Pending_Sectors -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 197 000 - 83 200 Multi_Zone_Error_Rate -O-R-- 253 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 100 000 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x03) instead Device Error Count: 3179 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3179 [2] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 06 30 00 00 11 02 28 70 40 00 Error: UNC at LBA = 0x11022870 = 285354096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 06 30 00 00 11 02 28 70 40 00 4d+13:32:03.500 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 4d+13:31:59.625 CHECK POWER MODE ec 10 00 00 00 00 00 00 00 00 00 00 00 4d+13:31:59.625 IDENTIFY DEVICE ef 00 10 00 02 00 00 00 00 00 00 a0 00 4d+13:31:59.625 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 4d+13:31:59.625 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 3178 [1] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 15 a8 00 00 11 02 28 70 40 00 Error: AMNF at LBA = 0x11022870 = 285354096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 15 a8 00 00 11 02 28 70 40 00 4d+13:31:59.500 READ FPDMA QUEUED ec 10 00 00 00 00 00 00 00 00 00 00 00 4d+13:31:55.188 IDENTIFY DEVICE ef 00 10 00 02 00 00 00 00 00 00 a0 00 4d+13:31:55.188 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 4d+13:31:55.188 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 4d+13:31:55.188 IDENTIFY DEVICE Error 3177 [0] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 0d 68 00 00 11 02 28 70 40 00 Error: AMNF at LBA = 0x11022870 = 285354096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 10 08 0d 68 00 00 11 02 28 70 40 00 4d+13:31:55.000 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 4d+13:31:50.688 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 4d+13:31:50.688 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 4d+13:31:50.688 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 4d+13:31:50.688 SET FEATURES [Set transfer mode] Error 3176 [7] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 16 b0 00 00 11 02 28 70 40 00 Error: AMNF at LBA = 0x11022870 = 285354096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 10 08 16 b0 00 00 11 02 28 70 40 00 4d+13:31:50.563 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 4d+13:31:46.250 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 4d+13:31:46.250 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 4d+13:31:46.250 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 4d+13:31:46.250 SET FEATURES [Set transfer mode] Error 3175 [6] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 40 00 00 11 02 28 70 40 00 Error: UNC at LBA = 0x11022870 = 285354096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 08 08 40 00 00 11 02 28 70 40 00 4d+13:31:46.125 READ FPDMA QUEUED 60 08 08 07 38 00 00 11 02 28 68 40 00 4d+13:31:42.563 READ FPDMA QUEUED 60 08 08 12 90 00 00 11 02 28 60 40 00 4d+13:31:42.563 READ FPDMA QUEUED 60 08 08 11 88 00 00 11 02 28 58 40 00 4d+13:31:42.563 READ FPDMA QUEUED 60 08 08 10 80 00 00 11 02 28 50 40 00 4d+13:31:42.563 READ FPDMA QUEUED Error 3174 [5] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 02 10 00 00 11 02 28 00 40 00 Error: AMNF at LBA = 0x11022800 = 285353984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 80 80 02 10 00 00 11 02 28 00 40 00 4d+13:31:42.438 READ FPDMA QUEUED 60 80 80 01 08 00 00 11 02 27 80 40 00 4d+13:31:38.125 READ FPDMA QUEUED 60 80 80 00 00 00 00 11 02 27 00 40 00 4d+13:31:38.125 READ FPDMA QUEUED 60 80 80 1f f8 00 00 11 02 26 80 40 00 4d+13:31:38.125 READ FPDMA QUEUED 60 80 80 17 b8 00 00 11 02 26 00 40 00 4d+13:31:38.063 READ FPDMA QUEUED Error 3173 [4] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 08 00 00 11 02 28 70 40 00 Error: UNC at LBA = 0x11022870 = 285354096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 10 08 01 08 00 00 11 02 28 70 40 00 4d+01:00:10.875 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 4d+01:00:04.438 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 4d+01:00:04.438 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 4d+01:00:04.375 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 4d+01:00:04.375 SET FEATURES [Set transfer mode] Error 3172 [3] occurred at disk power-on lifetime: 6327 hours (263 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 13 98 00 00 11 02 28 70 40 00 Error: UNC at LBA = 0x11022870 = 285354096 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 10 08 13 98 00 00 11 02 28 70 40 00 4d+01:00:04.250 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 4d+00:59:59.750 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 4d+00:59:59.750 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 4d+00:59:59.750 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 4d+00:59:59.750 SET FEATURES [Set transfer mode] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 90% 6344 - # 2 Short offline Completed: read failure 90% 6303 285354100 # 3 Extended offline Completed: read failure 90% 6192 285354100 # 4 Short offline Completed: read failure 90% 6188 285354100 # 5 Short offline Completed: read failure 90% 5980 285354100 # 6 Extended offline Completed: read failure 90% 5977 285354100 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 30/33 Celsius Lifetime Min/Max Temperature: 10/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (14) Index Estimated Time Temperature Celsius 15 2025-09-01 17:12 32 ************* 16 2025-09-01 17:13 33 ************** 17 2025-09-01 17:14 32 ************* ... ..(124 skipped). .. ************* 14 2025-09-01 19:19 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific /dev/sdd smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.0-63.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint T166 Device Model: SAMSUNG HD501LJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: CR100-13 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.5/5706 ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Mon Sep 1 19:19:42 2025 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9306) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 159) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 253 091 051 - 0 3 Spin_Up_Time POS--- 100 100 015 - 7616 4 Start_Stop_Count -O--CK 099 099 000 - 1788 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 1 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 7977 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1258 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 18590 187 Reported_Uncorrect -O--CK 253 253 000 - 5701632 188 Command_Timeout -O--CK 100 100 000 - 1 190 Airflow_Temperature_Cel -O---K 064 054 000 - 36 194 Temperature_Celsius -O---K 130 100 000 - 36 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 18590 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Total_Pending_Sectors -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 253 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x06) instead Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 1686 hours (70 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 16 b0 00 00 26 c0 ed 27 40 00 Error: ICRC, ABRT at LBA = 0x26c0ed27 = 650177831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 08 08 16 b0 00 00 26 c0 ed 27 40 00 00:05:18.250 WRITE FPDMA QUEUED 61 08 08 16 b0 00 00 26 c0 ec 3f 40 00 00:05:18.250 WRITE FPDMA QUEUED 61 08 08 16 b0 00 00 26 c0 ea ff 40 00 00:05:18.250 WRITE FPDMA QUEUED 61 08 08 16 b0 00 00 00 00 00 df 40 00 00:05:18.250 WRITE FPDMA QUEUED 61 01 08 16 b0 00 00 00 01 05 87 40 00 00:05:18.250 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 1545 hours (64 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 18 e8 00 00 03 bb e5 25 40 00 Error: ABRT at LBA = 0x03bbe525 = 62645541 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 40 08 18 e8 00 00 03 bb e5 25 40 00 00:11:55.125 WRITE FPDMA QUEUED 61 40 08 18 e8 00 00 03 bb e5 25 40 00 00:11:55.125 WRITE FPDMA QUEUED 60 08 40 0a c0 00 00 29 a1 6a 77 40 00 00:11:55.125 READ FPDMA QUEUED 60 40 40 1d 50 00 00 29 db 2a 9f 40 00 00:11:55.125 READ FPDMA QUEUED 61 20 08 10 e8 00 00 03 bb e5 1d 40 00 00:11:55.125 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 1533 hours (63 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 07 38 00 00 25 54 b5 a7 40 00 Error: ICRC, ABRT at LBA = 0x2554b5a7 = 626308519 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 20 20 07 38 00 00 25 54 b5 a7 40 00 00:10:13.938 WRITE FPDMA QUEUED 61 08 20 07 38 00 00 25 55 03 e7 40 00 00:10:13.938 WRITE FPDMA QUEUED 61 20 08 07 38 00 00 00 00 00 df 40 00 00:10:13.938 WRITE FPDMA QUEUED 61 08 20 07 38 00 00 25 54 b5 a7 40 00 00:10:13.938 WRITE FPDMA QUEUED 61 08 08 07 38 00 00 00 00 00 d7 40 00 00:10:13.938 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 1177 hours (49 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 1c e0 00 00 08 d4 1c 4c 40 00 Error: ICRC, ABRT at LBA = 0x08d41c4c = 148118604 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 10 08 1c e0 00 00 08 d4 1c 4c 40 00 01:10:01.563 WRITE FPDMA QUEUED 61 08 10 1c e0 00 00 08 d4 1c 3c 40 00 01:10:01.563 WRITE FPDMA QUEUED 61 0c 08 1c e0 00 00 08 d4 1c 34 40 00 01:10:01.563 WRITE FPDMA QUEUED 61 08 0c 1c e0 00 00 08 d4 1c 28 40 00 01:10:01.563 WRITE FPDMA QUEUED 61 01 08 1c e0 00 00 00 00 00 df 40 00 01:10:01.563 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 1172 hours (48 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 0b 50 00 00 1b 4d b3 17 40 00 Error: ICRC, ABRT at LBA = 0x1b4db317 = 458076951 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 80 80 0b 50 00 00 1b 4d b3 17 40 00 00:22:07.500 WRITE FPDMA QUEUED 61 80 80 0c 60 00 00 1b 4d b2 17 40 00 00:22:06.938 WRITE FPDMA QUEUED 61 80 80 0c 60 00 00 1b 4d b1 97 40 00 00:22:06.938 WRITE FPDMA QUEUED 61 80 80 0c 60 00 00 1b 4d b1 17 40 00 00:22:06.938 WRITE FPDMA QUEUED 61 80 80 0c 60 00 00 1b 4d b0 97 40 00 00:22:06.938 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 1130 hours (47 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 02 10 00 00 00 60 bd 7f 40 00 Error: ICRC, ABRT at LBA = 0x0060bd7f = 6339967 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 08 10 02 10 00 00 00 60 bd 7f 40 00 00:24:24.000 WRITE FPDMA QUEUED 61 08 08 02 10 00 00 00 60 bd 27 40 00 00:24:24.000 WRITE FPDMA QUEUED 61 08 08 02 10 00 00 00 60 bd 17 40 00 00:24:24.000 WRITE FPDMA QUEUED 61 08 08 02 10 00 00 00 60 bc e7 40 00 00:24:24.000 WRITE FPDMA QUEUED 61 08 08 11 10 00 00 00 60 b5 17 40 00 00:24:24.000 WRITE FPDMA QUEUED SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 7590 - # 2 Short offline Completed without error 00% 7584 - # 3 Extended offline Completed without error 00% 7375 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 32/36 Celsius Lifetime Min/Max Temperature: 9/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (14) Index Estimated Time Temperature Celsius 15 2025-09-01 17:12 36 ***************** ... ..(126 skipped). .. ***************** 14 2025-09-01 19:19 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific