/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.14.14-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: KINGSTON SA400S37120G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: SBFKJ1A3 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 28 01:36:48 2021 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x00) Offline data collection not supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 1464 12 Power_Cycle_Count -O--CK 100 100 000 - 935 148 Unknown_Attribute ------ 100 100 000 - 0 149 Unknown_Attribute ------ 100 100 000 - 0 167 Write_Protect_Mode ------ 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 169 Bad_Block_Rate ------ 100 100 000 - 45 170 Bad_Blk_Ct_Erl/Lat ------ 100 100 010 - 0/14 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 MaxAvgErase_Ct ------ 100 100 000 - 136 (Average 129) 181 Program_Fail_Count -O--CK 100 100 000 - 0 182 Erase_Fail_Count ------ 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 400 194 Temperature_Celsius -O---K 034 050 000 - 34 (Min/Max 5/50) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0 218 CRC_Error_Count -O--CK 100 100 000 - 1 231 SSD_Life_Left ------ 087 087 000 - 87 233 Flash_Writes_GiB -O--CK 100 100 000 - 7394 241 Lifetime_Writes_GiB -O--CK 100 100 000 - 4448 242 Lifetime_Reads_GiB -O--CK 100 100 000 - 6613 244 Average_Erase_Count ------ 100 100 000 - 129 245 Max_Erase_Count ------ 100 100 000 - 136 246 Total_Erase_Count ------ 100 100 000 - 221248 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 02 13 00 00 00 9f 80 18 e0 00 Error: ICRC, ABRT 531 sectors at LBA = 0x009f8018 = 10453016 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 13 00 00 00 9f 80 18 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 40 00 00 00 66 5e c0 e0 00 00:00:00.000 READ DMA EXT 25 00 00 01 12 00 00 00 2a 9a 20 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 56 00 00 00 2d 64 c8 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 40 00 00 00 64 8b 40 e0 00 00:00:00.000 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 935 --- Lifetime Power-On Resets 0x01 0x010 4 1464 --- Power-on Hours 0x01 0x018 6 9330088621 --- Logical Sectors Written 0x01 0x028 6 13868521760 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 34 --- Current Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 5 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 1 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 12 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 8 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.14.14-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD5000BEVT-60A0RT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.01A02 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Oct 28 01:36:48 2021 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12780) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 149) minutes. SCT capabilities: (0x703f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 43 3 Spin_Up_Time POS--K 181 153 021 - 1950 4 Start_Stop_Count -O--CK 096 096 000 - 4815 5 Reallocated_Sector_Ct PO--CK 151 151 140 - 535 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 088 088 000 - 9252 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4683 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 001 000 - 1430 188 Command_Timeout -O--CK 085 001 000 - 442388645079 190 Airflow_Temperature_Cel -O---K 069 044 040 - 31 (Min/Max 31/31) 191 G-Sense_Error_Rate -O--CK 001 001 000 - 3748 192 Power-Off_Retract_Count -O--CK 200 200 000 - 370 193 Load_Cycle_Count -O--CK 001 001 000 - 1124400 194 Temperature_Celsius -O---K 116 091 000 - 31 196 Reallocated_Event_Count -O--CK 125 125 000 - 75 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 17958 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 17958 [21] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- e3 00 00 00 00 00 00 00 00 00 00 40 00 01:05:14.524 IDLE ef 00 05 00 fe 00 00 00 00 00 00 40 00 01:05:14.504 SET FEATURES [Enable APM] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.355 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.353 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Set transfer mode] Error 17957 [20] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 fe 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 05 00 fe 00 00 00 00 00 00 40 00 01:05:14.504 SET FEATURES [Enable APM] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.355 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.353 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Enable SATA feature] Error 17956 [19] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.355 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.353 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.348 IDENTIFY DEVICE Error 17955 [18] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 45 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.348 IDENTIFY DEVICE 25 00 00 00 08 00 00 3a 38 5f 80 e0 00 01:05:14.338 READ DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.337 SET FEATURES [Enable SATA feature] Error 17954 [17] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.352 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.348 IDENTIFY DEVICE 25 00 00 00 08 00 00 3a 38 5f 80 e0 00 01:05:14.338 READ DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.337 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.334 IDENTIFY DEVICE Error 17953 [16] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 08 00 00 3a 38 5f 80 e0 00 Device Fault; Error: ABRT 8 sectors at LBA = 0x3a385f80 = 976772992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 3a 38 5f 80 e0 00 01:05:14.338 READ DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.337 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.334 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 00 01:05:14.334 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.334 SET FEATURES [Enable SATA feature] Error 17952 [15] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.337 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.334 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 00 01:05:14.334 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.334 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.332 IDENTIFY DEVICE Error 17951 [14] occurred at disk power-on lifetime: 9252 hours (385 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 45 00 00 00 00 00 00 a0 00 01:05:14.334 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.334 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:05:14.332 IDENTIFY DEVICE 25 00 00 00 08 00 00 3a 38 5f 80 e0 00 01:05:14.324 READ DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 00 01:05:14.323 SET FEATURES [Enable SATA feature] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 7840 - # 2 Short offline Completed without error 00% 7838 - # 3 Short offline Completed without error 00% 3 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 31/31 Celsius Lifetime Min/Max Temperature: 28/56 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (28) Index Estimated Time Temperature Celsius 29 2021-10-27 23:29 29 ********** 30 2021-10-27 23:30 30 *********** 31 2021-10-27 23:31 29 ********** 32 2021-10-27 23:32 30 *********** 33 2021-10-27 23:33 29 ********** ... ..( 3 skipped). .. ********** 37 2021-10-27 23:37 29 ********** 38 2021-10-27 23:38 ? - 39 2021-10-27 23:39 29 ********** ... ..( 10 skipped). .. ********** 50 2021-10-27 23:50 29 ********** 51 2021-10-27 23:51 30 *********** 52 2021-10-27 23:52 29 ********** 53 2021-10-27 23:53 30 *********** 54 2021-10-27 23:54 30 *********** 55 2021-10-27 23:55 ? - 56 2021-10-27 23:56 30 *********** 57 2021-10-27 23:57 ? - 58 2021-10-27 23:58 30 *********** 59 2021-10-27 23:59 ? - 60 2021-10-28 00:00 30 *********** ... ..( 6 skipped). .. *********** 67 2021-10-28 00:07 30 *********** 68 2021-10-28 00:08 29 ********** 69 2021-10-28 00:09 30 *********** ... ..( 9 skipped). .. *********** 79 2021-10-28 00:19 30 *********** 80 2021-10-28 00:20 ? - 81 2021-10-28 00:21 30 *********** 82 2021-10-28 00:22 ? - 83 2021-10-28 00:23 30 *********** ... ..( 27 skipped). .. *********** 111 2021-10-28 00:51 30 *********** 112 2021-10-28 00:52 31 ************ ... ..( 4 skipped). .. ************ 117 2021-10-28 00:57 31 ************ 118 2021-10-28 00:58 32 ************* ... ..( 5 skipped). .. ************* 124 2021-10-28 01:04 32 ************* 125 2021-10-28 01:05 33 ************** ... ..( 10 skipped). .. ************** 8 2021-10-28 01:16 33 ************** 9 2021-10-28 01:17 32 ************* ... ..( 4 skipped). .. ************* 14 2021-10-28 01:22 32 ************* 15 2021-10-28 01:23 31 ************ 16 2021-10-28 01:24 31 ************ 17 2021-10-28 01:25 ? - 18 2021-10-28 01:26 31 ************ ... ..( 9 skipped). .. ************ 28 2021-10-28 01:36 31 ************ SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 614 Vendor specific