/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD5000AADS-00M2B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.00A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Oct 11 05:00:40 2010 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 120) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 118 095 021 - 7075 4 Start_Stop_Count -O--CK 085 085 000 - 15678 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 087 087 000 - 9821 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5733 192 Power-Off_Retract_Count -O--CK 200 200 000 - 151 193 Load_Cycle_Count -O--CK 001 001 000 - 688746 194 Temperature_Celsius -O---K 118 097 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 185 185 000 - 1269 198 Offline_Uncorrectable ----CK 187 186 000 - 1114 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 193 193 000 - 1436 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 70 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 70 [21] occurred at disk power-on lifetime: 9591 hours (399 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1e 27 b7 e0 40 00 Error: UNC 8 sectors at LBA = 0x1e27b7e0 = 505919456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:42.802 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:40.272 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:37.741 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:35.211 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:32.688 READ DMA EXT Error 69 [20] occurred at disk power-on lifetime: 9591 hours (399 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1e 27 b7 e0 40 00 Error: UNC 8 sectors at LBA = 0x1e27b7e0 = 505919456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:40.272 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:37.741 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:35.211 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:32.688 READ DMA EXT 25 00 00 00 08 00 00 1e 27 2a 08 40 00 00:00:32.675 READ DMA EXT Error 68 [19] occurred at disk power-on lifetime: 9591 hours (399 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1e 27 b7 e0 40 00 Error: UNC 8 sectors at LBA = 0x1e27b7e0 = 505919456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:37.741 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:35.211 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:32.688 READ DMA EXT 25 00 00 00 08 00 00 1e 27 2a 08 40 00 00:00:32.675 READ DMA EXT 25 00 00 00 20 00 00 1e 27 29 d8 40 00 00:00:32.675 READ DMA EXT Error 67 [18] occurred at disk power-on lifetime: 9591 hours (399 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1e 27 b7 e0 40 00 Error: UNC 8 sectors at LBA = 0x1e27b7e0 = 505919456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:35.211 READ DMA EXT 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:32.688 READ DMA EXT 25 00 00 00 08 00 00 1e 27 2a 08 40 00 00:00:32.675 READ DMA EXT 25 00 00 00 20 00 00 1e 27 29 d8 40 00 00:00:32.675 READ DMA EXT 25 00 00 00 80 00 00 1e 27 29 40 40 00 00:00:32.674 READ DMA EXT Error 66 [17] occurred at disk power-on lifetime: 9591 hours (399 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1e 27 b7 e0 40 00 Error: UNC 8 sectors at LBA = 0x1e27b7e0 = 505919456 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1e 27 b7 e0 40 00 00:00:32.688 READ DMA EXT 25 00 00 00 08 00 00 1e 27 2a 08 40 00 00:00:32.675 READ DMA EXT 25 00 00 00 20 00 00 1e 27 29 d8 40 00 00:00:32.675 READ DMA EXT 25 00 00 00 80 00 00 1e 27 29 40 40 00 00:00:32.674 READ DMA EXT 25 00 00 00 80 00 00 1e 27 28 c0 40 00 00:00:32.674 READ DMA EXT Error 65 [16] occurred at disk power-on lifetime: 9577 hours (399 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 1e 31 ec f8 40 00 Error: UNC 2048 sectors at LBA = 0x1e31ecf8 = 506588408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:49.185 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:46.466 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:43.602 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:40.483 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:37.771 READ DMA EXT Error 64 [15] occurred at disk power-on lifetime: 9577 hours (399 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 1e 31 ec f8 40 00 Error: UNC 2048 sectors at LBA = 0x1e31ecf8 = 506588408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:46.466 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:43.602 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:40.483 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:37.771 READ DMA EXT 25 00 00 08 00 00 00 1e 31 e4 f8 40 00 00:20:37.762 READ DMA EXT Error 63 [14] occurred at disk power-on lifetime: 9577 hours (399 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 1e 31 ec f8 40 00 Error: UNC 2048 sectors at LBA = 0x1e31ecf8 = 506588408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:43.602 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:40.483 READ DMA EXT 25 00 00 08 00 00 00 1e 31 ec f8 40 00 00:20:37.771 READ DMA EXT 25 00 00 08 00 00 00 1e 31 e4 f8 40 00 00:20:37.762 READ DMA EXT 25 00 00 08 00 00 00 1e 31 dc f8 40 00 00:20:37.755 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 9814 496230456 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 28/31 Celsius Lifetime Min/Max Temperature: 28/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (404) Index Estimated Time Temperature Celsius 405 2010-10-10 21:03 34 *************** ... ..( 18 skipped). .. *************** 424 2010-10-10 21:22 34 *************** 425 2010-10-10 21:23 ? - 426 2010-10-10 21:24 34 *************** 427 2010-10-10 21:25 ? - 428 2010-10-10 21:26 34 *************** 429 2010-10-10 21:27 ? - 430 2010-10-10 21:28 34 *************** ... ..( 8 skipped). .. *************** 439 2010-10-10 21:37 34 *************** 440 2010-10-10 21:38 33 ************** ... ..( 2 skipped). .. ************** 443 2010-10-10 21:41 33 ************** 444 2010-10-10 21:42 34 *************** ... ..( 5 skipped). .. *************** 450 2010-10-10 21:48 34 *************** 451 2010-10-10 21:49 35 **************** 452 2010-10-10 21:50 35 **************** 453 2010-10-10 21:51 35 **************** 454 2010-10-10 21:52 34 *************** ... ..( 16 skipped). .. *************** 471 2010-10-10 22:09 34 *************** 472 2010-10-10 22:10 35 **************** 473 2010-10-10 22:11 34 *************** 474 2010-10-10 22:12 35 **************** ... ..( 77 skipped). .. **************** 74 2010-10-10 23:30 35 **************** 75 2010-10-10 23:31 34 *************** ... ..( 5 skipped). .. *************** 81 2010-10-10 23:37 34 *************** 82 2010-10-10 23:38 33 ************** ... ..( 4 skipped). .. ************** 87 2010-10-10 23:43 33 ************** 88 2010-10-10 23:44 34 *************** 89 2010-10-10 23:45 33 ************** ... ..( 39 skipped). .. ************** 129 2010-10-11 00:25 33 ************** 130 2010-10-11 00:26 ? - 131 2010-10-11 00:27 29 ********** ... ..( 2 skipped). .. ********** 134 2010-10-11 00:30 29 ********** 135 2010-10-11 00:31 30 *********** ... ..( 5 skipped). .. *********** 141 2010-10-11 00:37 30 *********** 142 2010-10-11 00:38 31 ************ ... ..( 34 skipped). .. ************ 177 2010-10-11 01:13 31 ************ 178 2010-10-11 01:14 30 *********** ... ..(137 skipped). .. *********** 316 2010-10-11 03:32 30 *********** 317 2010-10-11 03:33 29 ********** ... ..( 8 skipped). .. ********** 326 2010-10-11 03:42 29 ********** 327 2010-10-11 03:43 30 *********** 328 2010-10-11 03:44 29 ********** ... ..( 28 skipped). .. ********** 357 2010-10-11 04:13 29 ********** 358 2010-10-11 04:14 28 ********* ... ..( 14 skipped). .. ********* 373 2010-10-11 04:29 28 ********* 374 2010-10-11 04:30 29 ********** 375 2010-10-11 04:31 29 ********** 376 2010-10-11 04:32 29 ********** 377 2010-10-11 04:33 37 ****************** ... ..( 20 skipped). .. ****************** 398 2010-10-11 04:54 37 ****************** 399 2010-10-11 04:55 ? - 400 2010-10-11 04:56 33 ************** 401 2010-10-11 04:57 33 ************** 402 2010-10-11 04:58 34 *************** 403 2010-10-11 04:59 34 *************** 404 2010-10-11 05:00 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 74 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 15529 Vendor specific