/dev/sda smartctl 6.6 (build date Jun 14 2018) [x86_64-linux-4.10.0-38-generic] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SPCC Solid State Disk Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: SBFM81.1 User Capacity: 60,022,480,896 bytes [60.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Aug 13 15:30:37 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 44 12 Power_Cycle_Count -O--C- 100 100 000 - 14 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO---- 084 084 000 - 123 173 Unknown_Attribute -O--C- 100 100 000 - 65539 192 Power-Off_Retract_Count -O--C- 100 100 000 - 11 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 Unknown_Attribute PO-R-- 100 100 050 - 0 231 Temperature_Celsius PO--C- 100 100 000 - 99 241 Total_LBAs_Written -O--C- 100 100 000 - 44 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 14 --- Lifetime Power-On Resets 0x01 0x010 4 44 --- Power-on Hours 0x01 0x018 6 94200052 --- Logical Sectors Written 0x01 0x028 6 32909203 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 10 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 6.6 (build date Jun 14 2018) [x86_64-linux-4.10.0-38-generic] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Hitachi HDS723020BLE640 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MX4OAAB0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Aug 13 15:30:37 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14726) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 246) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 70 3 Spin_Up_Time POS--- 152 152 024 - 265 (Average 232) 4 Start_Stop_Count -O--C- 100 100 000 - 677 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 093 093 000 - 50560 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 676 192 Power-Off_Retract_Count -O--CK 100 100 000 - 698 193 Load_Cycle_Count -O--C- 100 100 000 - 698 194 Temperature_Celsius -O---- 171 171 000 - 35 (Min/Max 15/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 7 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 7 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7 [2] occurred at disk power-on lifetime: 47088 hours (1962 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 10 00 00 79 1c 93 f0 09 00 Error: ICRC, ABRT 16 sectors at LBA = 0x791c93f0 = 2031916016 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 04 00 00 00 79 1c 90 00 e0 08 1d+06:19:29.406 WRITE DMA EXT 35 00 00 00 c8 00 00 78 5c 20 60 e0 08 1d+06:19:29.406 WRITE DMA EXT 35 00 00 00 08 00 00 74 a7 c5 a0 e0 08 1d+06:19:29.405 WRITE DMA EXT 35 00 00 00 08 00 00 70 27 c0 00 e0 08 1d+06:19:29.405 WRITE DMA EXT 35 00 00 00 08 00 00 76 4d e0 c0 e0 08 1d+06:19:29.405 WRITE DMA EXT Error 6 [1] occurred at disk power-on lifetime: 45407 hours (1891 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 02 49 00 00 74 7d 90 e7 04 00 Error: ICRC, ABRT 585 sectors at LBA = 0x747d90e7 = 1954386151 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 03 18 00 00 74 7d 90 18 e0 08 4d+02:07:35.976 WRITE DMA EXT 35 00 00 00 20 00 00 74 6e a8 80 e0 08 4d+02:07:35.976 WRITE DMA EXT 35 00 00 00 08 00 00 74 6c 16 58 e0 08 4d+02:07:35.976 WRITE DMA EXT ea 00 00 00 00 00 00 88 ed 84 3f a0 08 4d+02:07:35.041 FLUSH CACHE EXT 35 00 00 00 08 00 00 88 ed 84 38 e0 08 4d+02:07:35.040 WRITE DMA EXT Error 5 [0] occurred at disk power-on lifetime: 44279 hours (1844 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 04 58 00 00 d8 e2 b8 30 08 00 Error: ICRC, ABRT 1112 sectors at LBA = 0xd8e2b830 = 3638736944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 04 88 00 00 d8 e2 b8 00 e0 08 2d+09:36:29.295 WRITE DMA EXT 35 00 00 00 08 00 00 74 71 30 38 e0 08 2d+09:36:29.295 WRITE DMA EXT 35 00 00 00 08 00 00 74 6b de 38 e0 08 2d+09:36:29.294 WRITE DMA EXT ea 00 00 00 00 00 00 88 ed 01 37 a0 08 2d+09:36:24.334 FLUSH CACHE EXT 35 00 00 00 08 00 00 88 ed 01 30 e0 08 2d+09:36:24.334 WRITE DMA EXT Error 4 [3] occurred at disk power-on lifetime: 12837 hours (534 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 0b 34 9e 7f 0b 00 Error: ICRC, ABRT 1 sectors at LBA = 0x0b349e7f = 187997823 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 20 00 00 0b 34 9e 60 e0 00 5d+17:33:42.520 WRITE DMA EXT 35 00 00 00 20 00 00 28 9e 46 a0 e0 00 5d+17:33:42.519 WRITE DMA EXT 35 00 00 00 20 00 00 0b 34 9e 40 e0 00 5d+17:33:42.519 WRITE DMA EXT 35 00 00 00 20 00 00 28 9e 46 a0 e0 00 5d+17:33:42.517 WRITE DMA EXT 35 00 00 00 20 00 00 0b 34 9e 20 e0 00 5d+17:33:42.517 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 34/36 Celsius Lifetime Min/Max Temperature: 15/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2019-08-13 13:23 34 *************** ... ..( 29 skipped). .. *************** 76 2019-08-13 13:53 34 *************** 77 2019-08-13 13:54 35 **************** 78 2019-08-13 13:55 34 *************** ... ..( 3 skipped). .. *************** 82 2019-08-13 13:59 34 *************** 83 2019-08-13 14:00 35 **************** 84 2019-08-13 14:01 34 *************** 85 2019-08-13 14:02 35 **************** 86 2019-08-13 14:03 34 *************** ... ..( 3 skipped). .. *************** 90 2019-08-13 14:07 34 *************** 91 2019-08-13 14:08 35 **************** 92 2019-08-13 14:09 34 *************** 93 2019-08-13 14:10 35 **************** 94 2019-08-13 14:11 34 *************** ... ..( 3 skipped). .. *************** 98 2019-08-13 14:15 34 *************** 99 2019-08-13 14:16 35 **************** ... ..( 2 skipped). .. **************** 102 2019-08-13 14:19 35 **************** 103 2019-08-13 14:20 34 *************** 104 2019-08-13 14:21 34 *************** 105 2019-08-13 14:22 34 *************** 106 2019-08-13 14:23 35 **************** 107 2019-08-13 14:24 34 *************** 108 2019-08-13 14:25 35 **************** ... ..( 16 skipped). .. **************** 125 2019-08-13 14:42 35 **************** 126 2019-08-13 14:43 36 ***************** 127 2019-08-13 14:44 36 ***************** 0 2019-08-13 14:45 36 ***************** 1 2019-08-13 14:46 35 **************** 2 2019-08-13 14:47 35 **************** 3 2019-08-13 14:48 36 ***************** 4 2019-08-13 14:49 35 **************** ... ..( 40 skipped). .. **************** 45 2019-08-13 15:30 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 676 --- Lifetime Power-On Resets 0x01 0x010 4 50560 --- Power-on Hours 0x01 0x018 6 79333707699 --- Logical Sectors Written 0x01 0x020 6 706937949 --- Number of Write Commands 0x01 0x028 6 86360241910 --- Logical Sectors Read 0x01 0x030 6 698395877 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 50552 --- Spindle Motor Power-on Hours 0x03 0x010 4 50552 --- Head Flying Hours 0x03 0x018 4 698 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 7 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 4 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 33 N-- Average Short Term Temperature 0x05 0x018 1 37 N-- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 49 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 46 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3507 --- Number of Hardware Resets 0x06 0x010 4 2799 --- Number of ASR Events 0x06 0x018 4 7 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS