/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-4-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD502HJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AJ10001 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Nov 29 14:56:03 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4560) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 76) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 083 082 025 - 5327 4 Start_Stop_Count -O--CK 098 098 000 - 2486 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 15611 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2505 191 G-Sense_Error_Rate -O---K 100 100 000 - 2 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 055 000 - 35 (Min/Max 12/45) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 22 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 100 100 000 - 2507 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 13437 hours (559 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 6e 00 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 28160 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 01 00 00 00 04 03 6d 00 e0 08 00:00:14.000 WRITE DMA EXT 35 00 00 00 78 00 00 03 fe 55 00 e0 08 00:00:14.000 WRITE DMA EXT 35 00 00 01 00 00 00 03 fe 54 00 e0 08 00:00:14.000 WRITE DMA EXT 35 00 00 00 f8 00 00 03 a5 f9 10 e0 08 00:00:14.000 WRITE DMA EXT 35 00 00 01 00 00 00 03 a5 f8 10 e0 08 00:00:14.000 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 33/36 Celsius Lifetime Min/Max Temperature: 16/64 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (124) Index Estimated Time Temperature Celsius 125 2023-11-29 04:20 30 *********** 126 2023-11-29 04:25 30 *********** 127 2023-11-29 04:30 30 *********** 0 2023-11-29 04:35 31 ************ ... ..( 18 skipped). .. ************ 19 2023-11-29 06:10 31 ************ 20 2023-11-29 06:15 24 ***** 21 2023-11-29 06:20 26 ******* 22 2023-11-29 06:25 28 ********* 23 2023-11-29 06:30 29 ********** 24 2023-11-29 06:35 30 *********** ... ..( 6 skipped). .. *********** 31 2023-11-29 07:10 30 *********** 32 2023-11-29 07:15 31 ************ ... ..( 5 skipped). .. ************ 38 2023-11-29 07:45 31 ************ 39 2023-11-29 07:50 30 *********** 40 2023-11-29 07:55 30 *********** 41 2023-11-29 08:00 30 *********** 42 2023-11-29 08:05 31 ************ ... ..( 2 skipped). .. ************ 45 2023-11-29 08:20 31 ************ 46 2023-11-29 08:25 30 *********** 47 2023-11-29 08:30 30 *********** 48 2023-11-29 08:35 31 ************ 49 2023-11-29 08:40 30 *********** 50 2023-11-29 08:45 31 ************ ... ..( 3 skipped). .. ************ 54 2023-11-29 09:05 31 ************ 55 2023-11-29 09:10 32 ************* ... ..( 9 skipped). .. ************* 65 2023-11-29 10:00 32 ************* 66 2023-11-29 10:05 31 ************ ... ..( 9 skipped). .. ************ 76 2023-11-29 10:55 31 ************ 77 2023-11-29 11:00 32 ************* 78 2023-11-29 11:05 32 ************* 79 2023-11-29 11:10 32 ************* 80 2023-11-29 11:15 23 **** 81 2023-11-29 11:20 25 ****** 82 2023-11-29 11:25 26 ******* 83 2023-11-29 11:30 27 ******** 84 2023-11-29 11:35 28 ********* 85 2023-11-29 11:40 28 ********* 86 2023-11-29 11:45 29 ********** ... ..( 2 skipped). .. ********** 89 2023-11-29 12:00 29 ********** 90 2023-11-29 12:05 30 *********** 91 2023-11-29 12:10 29 ********** ... ..( 7 skipped). .. ********** 99 2023-11-29 12:50 29 ********** 100 2023-11-29 12:55 30 *********** ... ..( 2 skipped). .. *********** 103 2023-11-29 13:10 30 *********** 104 2023-11-29 13:15 35 **************** 105 2023-11-29 13:20 35 **************** 106 2023-11-29 13:25 34 *************** ... ..( 2 skipped). .. *************** 109 2023-11-29 13:40 34 *************** 110 2023-11-29 13:45 33 ************** ... ..( 3 skipped). .. ************** 114 2023-11-29 14:05 33 ************** 115 2023-11-29 14:10 34 *************** 116 2023-11-29 14:15 36 ***************** 117 2023-11-29 14:20 35 **************** 118 2023-11-29 14:25 35 **************** 119 2023-11-29 14:30 35 **************** 120 2023-11-29 14:35 34 *************** 121 2023-11-29 14:40 34 *************** 122 2023-11-29 14:45 34 *************** 123 2023-11-29 14:50 35 **************** 124 2023-11-29 14:55 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific