/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD2500BEVT-60A23T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.01A02 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Sep 26 22:00:02 2018 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6360) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 77) minutes. SCT capabilities: (0x703f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 156 142 021 - 1175 4 Start_Stop_Count -O--CK 098 098 000 - 2481 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 095 095 000 - 4075 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2429 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 099 000 - 2 188 Command_Timeout -O--CK 100 099 000 - 4295098373 190 Airflow_Temperature_Cel -O---K 067 036 040 Past 33 (0 11 33 24 0) 191 G-Sense_Error_Rate -O--CK 001 001 000 - 714 192 Power-Off_Retract_Count -O--CK 200 200 000 - 382 193 Load_Cycle_Count -O--CK 001 001 000 - 632506 194 Temperature_Celsius -O---K 110 079 000 - 33 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 1438 hours (59 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 20 00 00 00 68 5f 28 40 00 Error: IDNF at LBA = 0x00685f28 = 6840104 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 06 cd 79 d8 40 00 01:24:43.562 READ FPDMA QUEUED 61 00 20 00 f8 00 00 00 68 5f 28 40 00 01:24:41.738 WRITE FPDMA QUEUED 61 00 08 00 f0 00 00 00 49 41 40 40 00 01:24:41.177 WRITE FPDMA QUEUED 61 00 20 00 e8 00 00 03 8e f0 50 40 00 01:24:38.614 WRITE FPDMA QUEUED 61 00 08 00 e0 00 00 00 4c 1b 00 40 00 01:24:38.613 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 1212 hours (50 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 00 47 3f ea 40 00 Error: UNC at LBA = 0x00473fea = 4669418 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 30 00 00 00 47 3f ea 40 00 00:11:41.865 READ FPDMA QUEUED 60 00 20 00 28 00 00 00 47 5d 42 40 00 00:11:39.553 READ FPDMA QUEUED 60 00 20 00 20 00 00 00 70 67 d9 40 00 00:11:39.542 READ FPDMA QUEUED 60 00 20 00 18 00 00 00 70 68 59 40 00 00:11:39.520 READ FPDMA QUEUED 60 00 08 00 10 00 00 00 70 13 92 40 00 00:11:39.499 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 3735 - # 2 Extended offline Completed without error 00% 2968 - # 3 Extended offline Completed: read failure 90% 2815 43108354 # 4 Short offline Interrupted (host reset) 90% 2428 - 1 of 1 failed self-tests are outdated by newer successful extended offline self-test # 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 24/33 Celsius Lifetime Min/Max Temperature: ?/64 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (22) Index Estimated Time Temperature Celsius 23 2018-09-26 19:53 35 **************** ... ..( 4 skipped). .. **************** 28 2018-09-26 19:58 35 **************** 29 2018-09-26 19:59 36 ***************** 30 2018-09-26 20:00 36 ***************** 31 2018-09-26 20:01 36 ***************** 32 2018-09-26 20:02 35 **************** 33 2018-09-26 20:03 36 ***************** 34 2018-09-26 20:04 36 ***************** 35 2018-09-26 20:05 36 ***************** 36 2018-09-26 20:06 ? - 37 2018-09-26 20:07 24 ***** 38 2018-09-26 20:08 25 ****** 39 2018-09-26 20:09 27 ******** 40 2018-09-26 20:10 27 ******** 41 2018-09-26 20:11 27 ******** 42 2018-09-26 20:12 28 ********* ... ..( 2 skipped). .. ********* 45 2018-09-26 20:15 28 ********* 46 2018-09-26 20:16 29 ********** 47 2018-09-26 20:17 29 ********** 48 2018-09-26 20:18 30 *********** 49 2018-09-26 20:19 30 *********** 50 2018-09-26 20:20 30 *********** 51 2018-09-26 20:21 ? - 52 2018-09-26 20:22 28 ********* 53 2018-09-26 20:23 29 ********** 54 2018-09-26 20:24 29 ********** 55 2018-09-26 20:25 30 *********** 56 2018-09-26 20:26 30 *********** 57 2018-09-26 20:27 31 ************ ... ..( 2 skipped). .. ************ 60 2018-09-26 20:30 31 ************ 61 2018-09-26 20:31 32 ************* ... ..( 2 skipped). .. ************* 64 2018-09-26 20:34 32 ************* 65 2018-09-26 20:35 33 ************** 66 2018-09-26 20:36 33 ************** 67 2018-09-26 20:37 34 *************** 68 2018-09-26 20:38 33 ************** 69 2018-09-26 20:39 33 ************** 70 2018-09-26 20:40 34 *************** 71 2018-09-26 20:41 34 *************** 72 2018-09-26 20:42 35 **************** 73 2018-09-26 20:43 34 *************** 74 2018-09-26 20:44 35 **************** ... ..( 3 skipped). .. **************** 78 2018-09-26 20:48 35 **************** 79 2018-09-26 20:49 36 ***************** ... ..( 12 skipped). .. ***************** 92 2018-09-26 21:02 36 ***************** 93 2018-09-26 21:03 37 ****************** ... ..( 5 skipped). .. ****************** 99 2018-09-26 21:09 37 ****************** 100 2018-09-26 21:10 36 ***************** 101 2018-09-26 21:11 38 ******************* 102 2018-09-26 21:12 37 ****************** 103 2018-09-26 21:13 38 ******************* ... ..( 10 skipped). .. ******************* 114 2018-09-26 21:24 38 ******************* 115 2018-09-26 21:25 39 ******************** ... ..( 15 skipped). .. ******************** 3 2018-09-26 21:41 39 ******************** 4 2018-09-26 21:42 40 ********************* 5 2018-09-26 21:43 40 ********************* 6 2018-09-26 21:44 39 ******************** 7 2018-09-26 21:45 40 ********************* 8 2018-09-26 21:46 39 ******************** 9 2018-09-26 21:47 39 ******************** 10 2018-09-26 21:48 40 ********************* 11 2018-09-26 21:49 ? - 12 2018-09-26 21:50 24 ***** 13 2018-09-26 21:51 25 ****** 14 2018-09-26 21:52 26 ******* 15 2018-09-26 21:53 26 ******* 16 2018-09-26 21:54 28 ********* 17 2018-09-26 21:55 29 ********** 18 2018-09-26 21:56 30 *********** 19 2018-09-26 21:57 30 *********** 20 2018-09-26 21:58 31 ************ 21 2018-09-26 21:59 32 ************* 22 2018-09-26 22:00 33 ************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 669 Vendor specific