Probe #78dabdae6c of ASRock 870 Extreme3 Desktop Computer

Log: smartctl

/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.12.4-desktop-1omv4050] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3360320AS Serial Number: -- Firmware Version: 3.AAM User Capacity: 360,080,695,296 bytes [360 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Fri Jul 16 19:06:49 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 132) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 096 095 000 - 0 4 Start_Stop_Count -O--CK 098 098 020 - 2611 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 069 054 030 - 167787950510 9 Power_On_Hours -O--CK 093 093 000 - 6136 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 098 098 020 - 2612 187 Reported_Uncorrect -O--CK 033 033 000 - 67 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 067 055 045 - 33 (Min/Max 26/33) 194 Temperature_Celsius -O---K 033 045 000 - 33 (0 13 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 073 062 000 - 93677003 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 67 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 67 [6] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:23.432 READ DMA EXT 25 00 00 00 20 00 00 16 00 64 7f e0 00 00:07:23.465 READ DMA EXT 25 00 00 00 08 00 00 ef 00 00 3f e0 00 00:07:23.465 READ DMA EXT 35 00 00 00 20 00 00 ee 00 5f 8f e0 00 00:07:23.441 WRITE DMA EXT 35 00 00 00 08 00 00 16 00 64 5f e0 00 00:07:23.441 WRITE DMA EXT Error 66 [5] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:21.206 READ DMA EXT 25 00 00 00 20 00 00 16 00 64 3f e0 00 00:07:21.231 READ DMA EXT 35 00 00 00 08 00 00 16 00 64 1f e0 00 00:07:21.209 WRITE DMA EXT 35 00 00 00 10 00 00 15 00 64 ef e0 00 00:07:21.208 WRITE DMA EXT 35 00 00 00 10 00 00 15 00 64 cf e0 00 00:07:21.208 WRITE DMA EXT Error 65 [4] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:19.065 READ DMA EXT 35 00 00 00 08 00 1e c6 00 7b 9f e0 00 00:07:19.064 WRITE DMA EXT 35 00 00 00 08 00 1e e8 00 87 07 e0 00 00:07:19.064 WRITE DMA EXT 35 00 00 00 08 00 1e e7 00 87 d7 e0 00 00:07:19.070 WRITE DMA EXT 35 00 00 00 08 00 1e e7 00 87 77 e0 00 00:07:19.067 WRITE DMA EXT Error 64 [3] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:25.550 READ DMA EXT 35 00 00 00 05 00 1d ee 00 4c 57 e0 00 00:07:23.465 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 5e 47 a0 00 00:07:23.465 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 00 5e 47 e0 00 00:07:25.569 WRITE DMA EXT 35 00 00 00 08 00 18 94 00 1d 47 e0 00 00:07:25.569 WRITE DMA EXT Error 63 [2] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:23.432 READ DMA EXT 25 00 00 00 20 00 00 16 00 64 7f e0 00 00:07:23.465 READ DMA EXT 25 00 00 00 08 00 00 ef 00 00 3f e0 00 00:07:23.465 READ DMA EXT 35 00 00 00 20 00 00 ee 00 5f 8f e0 00 00:07:23.441 WRITE DMA EXT 35 00 00 00 08 00 00 16 00 64 5f e0 00 00:07:23.441 WRITE DMA EXT Error 62 [1] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:21.206 READ DMA EXT 25 00 00 00 20 00 00 16 00 64 3f e0 00 00:07:21.231 READ DMA EXT 35 00 00 00 08 00 00 16 00 64 1f e0 00 00:07:21.209 WRITE DMA EXT 35 00 00 00 10 00 00 15 00 64 ef e0 00 00:07:21.208 WRITE DMA EXT 35 00 00 00 10 00 00 15 00 64 cf e0 00 00:07:21.208 WRITE DMA EXT Error 61 [0] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:19.065 READ DMA EXT 35 00 00 00 08 00 1e c6 00 7b 9f e0 00 00:07:19.064 WRITE DMA EXT 35 00 00 00 08 00 1e e8 00 87 07 e0 00 00:07:19.064 WRITE DMA EXT 35 00 00 00 08 00 1e e7 00 87 d7 e0 00 00:07:19.070 WRITE DMA EXT 35 00 00 00 08 00 1e e7 00 87 77 e0 00 00:07:19.067 WRITE DMA EXT Error 60 [19] occurred at disk power-on lifetime: 4030 hours (167 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 20 36 00 84 f4 e0 00 Error: UNC at LBA = 0x20360084f4 = 138344957172 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 20 36 00 84 bf e0 00 00:07:25.550 READ DMA EXT 35 00 00 00 05 00 1d ee 00 4c 57 e0 00 00:07:23.465 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 5e 47 a0 00 00:07:23.465 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 00 5e 47 e0 00 00:07:25.569 WRITE DMA EXT 35 00 00 00 08 00 18 94 00 1d 47 e0 00 00:07:25.569 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS


Hardware for Linux and BSD

GitHub