/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-25-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: KINGSTON SA400S37240G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: S1Z40102 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 12 20:26:48 2023 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 000 - 100 9 Power_On_Hours -O--CK 100 100 000 - 6432 12 Power_Cycle_Count -O--CK 100 100 000 - 3573 148 Unknown_Attribute ------ 100 100 000 - 0 149 Unknown_Attribute ------ 100 100 000 - 0 167 Write_Protect_Mode ------ 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 169 Bad_Block_Rate ------ 100 100 000 - 0 170 Bad_Blk_Ct_Erl/Lat ------ 100 100 010 - 0/0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 MaxAvgErase_Ct ------ 100 100 000 - 0 181 Program_Fail_Count -O--CK 100 100 000 - 0 182 Erase_Fail_Count ------ 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 435 194 Temperature_Celsius -O---K 036 065 000 - 36 (Min/Max 19/65) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0 218 CRC_Error_Count -O--CK 100 100 000 - 0 231 SSD_Life_Left ------ 082 082 000 - 82 233 Flash_Writes_GiB -O--CK 100 100 000 - 13870 241 Lifetime_Writes_GiB -O--CK 100 100 000 - 9071 242 Lifetime_Reads_GiB -O--CK 100 100 000 - 9635 244 Average_Erase_Count ------ 100 100 000 - 182 245 Max_Erase_Count ------ 100 100 000 - 197 246 Total_Erase_Count ------ 100 100 000 - 78324 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Invalid Error Log index = 0x0000 (reserved = 0x00) SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3573 --- Lifetime Power-On Resets 0x01 0x010 4 6432 --- Power-on Hours 0x01 0x018 6 1844024354 --- Logical Sectors Written 0x01 0x020 6 228632 --- Number of Write Commands 0x01 0x028 6 3026732736 --- Logical Sectors Read 0x01 0x030 6 228539 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 29 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 1 R_ERR response for non-data FIS 0x000a 4 11 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-25-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 2.5" HDD MK..65GSX Device Model: TOSHIBA MK5065GSXF Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: GV108B User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Jul 12 20:26:48 2023 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 171) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 099 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 2058 4 Start_Stop_Count -O--CK 100 100 000 - 6328 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 676 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 067 067 000 - 13486 10 Spin_Retry_Count PO--CK 226 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 5601 191 G-Sense_Error_Rate -O--CK 100 100 000 - 23179 192 Power-Off_Retract_Count -O--CK 100 100 000 - 490 193 Load_Cycle_Count -O--CK 095 095 000 - 59926 194 Temperature_Celsius -O---K 100 100 000 - 36 (Min/Max 10/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 600 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 220 Disk_Shift -O---- 100 100 000 - 48 222 Loaded_Hours -O--CK 071 071 000 - 11779 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 333 240 Head_Flying_Hours P----- 100 100 001 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 149 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 302 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 302 [45] occurred at disk power-on lifetime: 6066 hours (252 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 90 00 00 24 56 5b 07 64 00 Error: ICRC, ABRT at LBA = 0x24565b07 = 609639175 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 05 40 00 90 00 00 24 56 55 c8 40 00 00:52:32.181 WRITE FPDMA QUEUED 61 05 40 00 88 00 00 24 56 50 88 40 00 00:52:32.168 WRITE FPDMA QUEUED 61 05 40 00 80 00 00 24 56 4b 48 40 00 00:52:32.155 WRITE FPDMA QUEUED 61 05 40 00 78 00 00 24 56 46 08 40 00 00:52:32.142 WRITE FPDMA QUEUED 61 05 40 00 70 00 00 24 56 40 c8 40 00 00:52:32.129 WRITE FPDMA QUEUED Error 301 [44] occurred at disk power-on lifetime: 1723 hours (71 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 c2 00 00 00 63 28 04 60 00 Error: WP at LBA = 0x00632804 = 6498308 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 20 00 38 00 00 1b 13 92 30 40 00 00:00:48.258 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 16 eb 20 00 40 00 00:00:48.258 WRITE FPDMA QUEUED 60 00 08 00 28 00 00 19 53 ce 28 40 00 00:00:48.253 READ FPDMA QUEUED 60 00 08 00 20 00 00 16 cf 90 30 40 00 00:00:48.248 READ FPDMA QUEUED 60 00 08 00 18 00 00 16 cf 90 28 40 00 00:00:48.248 READ FPDMA QUEUED Error 300 [43] occurred at disk power-on lifetime: 1723 hours (71 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 22 00 00 00 63 28 04 60 00 Error: UNC at LBA = 0x00632804 = 6498308 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f0 00 00 18 cf bf e8 40 00 00:00:40.298 READ FPDMA QUEUED 60 00 08 00 18 00 00 18 cf bf e0 40 00 00:00:40.288 READ FPDMA QUEUED 60 00 08 00 10 00 00 18 cf bf d8 40 00 00:00:40.288 READ FPDMA QUEUED 60 00 08 00 08 00 00 18 cf bf d0 40 00 00:00:40.288 READ FPDMA QUEUED 60 00 08 00 00 00 00 18 cf bf c8 40 00 00:00:40.288 READ FPDMA QUEUED Error 299 [42] occurred at disk power-on lifetime: 367 hours (15 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 4f 00 00 00 48 c0 22 e0 00 Error: UNC 79 sectors at LBA = 0x0048c022 = 4767778 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 7f 00 00 00 48 bf f2 e0 00 08:23:39.544 READ DMA EXT 25 00 00 00 7f 00 00 00 48 bf 73 e0 00 08:23:39.432 READ DMA EXT 25 00 00 00 7f 00 00 00 48 be f4 e0 00 08:23:39.431 READ DMA EXT 25 00 00 00 7f 00 00 00 48 be 75 e0 00 08:23:39.219 READ DMA EXT 25 00 00 00 7f 00 00 00 48 bd f6 e0 00 08:23:39.218 READ DMA EXT Error 298 [41] occurred at disk power-on lifetime: 364 hours (15 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 0a 00 00 03 08 ce 6a 63 00 Error: WP at LBA = 0x0308ce6a = 50908778 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 90 00 00 00 5f 15 40 40 00 04:47:36.541 WRITE FPDMA QUEUED 61 00 10 00 88 00 00 00 60 c0 20 40 00 04:47:36.541 WRITE FPDMA QUEUED 61 00 0e 00 80 00 00 03 6b 4c e0 40 00 04:47:36.535 WRITE FPDMA QUEUED 61 00 20 00 78 00 00 00 05 16 30 40 00 04:47:36.535 WRITE FPDMA QUEUED 61 00 01 00 70 00 00 00 0e 7e 78 40 00 04:47:36.184 WRITE FPDMA QUEUED Error 297 [40] occurred at disk power-on lifetime: 360 hours (15 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 4a 00 00 01 7e 1f 4d 61 00 Error: WP at LBA = 0x017e1f4d = 25042765 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 c8 00 00 00 5f 15 40 40 00 00:52:04.621 WRITE FPDMA QUEUED 61 00 08 00 c0 00 00 00 60 f4 88 40 00 00:52:04.621 WRITE FPDMA QUEUED 61 00 0a 00 b8 00 00 02 17 f0 a0 40 00 00:52:04.620 WRITE FPDMA QUEUED 61 00 20 00 b0 00 00 00 62 d1 00 40 00 00:52:04.620 WRITE FPDMA QUEUED 61 00 08 00 a8 00 00 00 5f 15 30 40 00 00:52:04.455 WRITE FPDMA QUEUED Error 296 [39] occurred at disk power-on lifetime: 359 hours (14 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 3a 00 00 01 7c bc b1 61 00 Error: WP at LBA = 0x017cbcb1 = 24951985 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 c8 00 00 00 68 30 08 40 00 00:24:31.264 WRITE FPDMA QUEUED 61 00 08 00 c0 00 00 00 63 21 30 40 00 00:24:31.264 WRITE FPDMA QUEUED 61 00 08 00 b8 00 00 00 5f 15 38 40 00 00:24:31.264 WRITE FPDMA QUEUED 61 00 08 00 b0 00 00 00 67 fd 28 40 00 00:24:31.264 WRITE FPDMA QUEUED 61 00 08 00 a8 00 00 00 63 1f d8 40 00 00:24:31.264 WRITE FPDMA QUEUED Error 295 [38] occurred at disk power-on lifetime: 359 hours (14 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 7a 00 00 01 7c bc b0 61 00 Error: WP at LBA = 0x017cbcb0 = 24951984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 40 00 c8 00 00 01 7b cb 60 40 00 00:24:21.493 WRITE FPDMA QUEUED 61 00 40 00 c0 00 00 01 8e b1 60 40 00 00:24:21.492 WRITE FPDMA QUEUED 61 00 40 00 b8 00 00 01 81 ad 60 40 00 00:24:21.492 WRITE FPDMA QUEUED 61 00 08 00 b0 00 00 00 5f 15 38 40 00 00:24:21.492 WRITE FPDMA QUEUED 61 00 40 00 a8 00 00 01 7f 6b 60 40 00 00:24:21.492 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 19/37 Celsius Lifetime Min/Max Temperature: 10/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (299) Index Estimated Time Temperature Celsius 300 2023-07-12 12:29 32 ************* ... ..( 9 skipped). .. ************* 310 2023-07-12 12:39 32 ************* 311 2023-07-12 12:40 33 ************** ... ..( 44 skipped). .. ************** 356 2023-07-12 13:25 33 ************** 357 2023-07-12 13:26 34 *************** ... ..(183 skipped). .. *************** 63 2023-07-12 16:30 34 *************** 64 2023-07-12 16:31 35 **************** ... ..( 47 skipped). .. **************** 112 2023-07-12 17:19 35 **************** 113 2023-07-12 17:20 34 *************** ... ..( 66 skipped). .. *************** 180 2023-07-12 18:27 34 *************** 181 2023-07-12 18:28 35 **************** ... ..( 11 skipped). .. **************** 193 2023-07-12 18:40 35 **************** 194 2023-07-12 18:41 36 ***************** ... ..( 48 skipped). .. ***************** 243 2023-07-12 19:30 36 ***************** 244 2023-07-12 19:31 37 ****************** ... ..( 38 skipped). .. ****************** 283 2023-07-12 20:10 37 ****************** 284 2023-07-12 20:11 36 ***************** ... ..( 14 skipped). .. ***************** 299 2023-07-12 20:26 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 1259 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 11 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC