Probe #826d1c0dc8 of ASUSTek K43SJ

Log: smartctl

/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.10.74-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K320 Device Model: Hitachi HTS543232A7A384 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: ES2OA60W User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Oct 4 08:43:35 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 97) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 230 230 033 - 1 4 Start_Stop_Count -O--C- 093 093 000 - 12394 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 063 063 000 - 16602 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 12360 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 098 098 000 - 416 193 Load_Cycle_Count -O--C- 067 067 000 - 335865 194 Temperature_Celsius -O---- 153 153 000 - 39 (Min/Max 17/59) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 9795 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9795 [2] occurred at disk power-on lifetime: 15434 hours (643 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 00 13 dd 12 00 00 Error: WP at LBA = 0x0013dd12 = 1301778 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 a0 00 00 05 2c 73 b0 40 00 01:01:15.216 WRITE FPDMA QUEUED 61 01 00 00 98 00 00 0a f9 82 58 40 00 01:01:15.216 WRITE FPDMA QUEUED 61 01 00 00 90 00 00 0a f9 81 58 40 00 01:01:15.216 WRITE FPDMA QUEUED 61 01 00 00 88 00 00 0a f9 80 58 40 00 01:01:15.216 WRITE FPDMA QUEUED 61 01 00 00 80 00 00 0a f9 7f 58 40 00 01:01:15.216 WRITE FPDMA QUEUED Error 9794 [1] occurred at disk power-on lifetime: 15434 hours (643 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 00 13 dd 12 00 00 Error: WP at LBA = 0x0013dd12 = 1301778 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 a0 00 00 05 2c 73 b0 40 00 01:01:11.883 WRITE FPDMA QUEUED 61 01 00 00 98 00 00 0a f9 82 58 40 00 01:01:11.883 WRITE FPDMA QUEUED 61 01 00 00 90 00 00 0a f9 81 58 40 00 01:01:11.882 WRITE FPDMA QUEUED 61 01 00 00 88 00 00 0a f9 80 58 40 00 01:01:11.882 WRITE FPDMA QUEUED 61 01 00 00 80 00 00 0a f9 7f 58 40 00 01:01:11.882 WRITE FPDMA QUEUED Error 9793 [0] occurred at disk power-on lifetime: 15434 hours (643 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 00 13 dd 12 00 00 Error: WP at LBA = 0x0013dd12 = 1301778 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 a0 00 00 05 2c 73 b0 40 00 01:01:08.548 WRITE FPDMA QUEUED 61 01 00 00 98 00 00 0a f9 82 58 40 00 01:01:08.548 WRITE FPDMA QUEUED 61 01 00 00 90 00 00 0a f9 81 58 40 00 01:01:08.548 WRITE FPDMA QUEUED 61 01 00 00 88 00 00 0a f9 80 58 40 00 01:01:08.548 WRITE FPDMA QUEUED 61 01 00 00 80 00 00 0a f9 7f 58 40 00 01:01:08.548 WRITE FPDMA QUEUED Error 9792 [3] occurred at disk power-on lifetime: 15434 hours (643 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 00 13 dd 12 00 00 Error: WP at LBA = 0x0013dd12 = 1301778 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 a0 00 00 05 2c 73 b0 40 00 01:01:05.215 WRITE FPDMA QUEUED 61 01 00 00 98 00 00 0a f9 82 58 40 00 01:01:05.215 WRITE FPDMA QUEUED 61 01 00 00 90 00 00 0a f9 81 58 40 00 01:01:05.215 WRITE FPDMA QUEUED 61 01 00 00 88 00 00 0a f9 80 58 40 00 01:01:05.215 WRITE FPDMA QUEUED 61 01 00 00 80 00 00 0a f9 7f 58 40 00 01:01:05.215 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 18/39 Celsius Lifetime Min/Max Temperature: 17/59 Celsius Specified Max Operating Temperature: 39 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (3) Index Estimated Time Temperature Celsius 4 2022-10-04 06:36 37 ****************** 5 2022-10-04 06:37 37 ****************** 6 2022-10-04 06:38 37 ****************** 7 2022-10-04 06:39 36 ***************** ... ..( 2 skipped). .. ***************** 10 2022-10-04 06:42 36 ***************** 11 2022-10-04 06:43 37 ****************** ... ..( 2 skipped). .. ****************** 14 2022-10-04 06:46 37 ****************** 15 2022-10-04 06:47 36 ***************** ... ..( 5 skipped). .. ***************** 21 2022-10-04 06:53 36 ***************** 22 2022-10-04 06:54 35 **************** ... ..( 4 skipped). .. **************** 27 2022-10-04 06:59 35 **************** 28 2022-10-04 07:00 36 ***************** 29 2022-10-04 07:01 ? - 30 2022-10-04 07:02 22 *** 31 2022-10-04 07:03 22 *** 32 2022-10-04 07:04 23 **** 33 2022-10-04 07:05 23 **** 34 2022-10-04 07:06 23 **** 35 2022-10-04 07:07 24 ***** 36 2022-10-04 07:08 24 ***** 37 2022-10-04 07:09 25 ****** ... ..( 2 skipped). .. ****** 40 2022-10-04 07:12 25 ****** 41 2022-10-04 07:13 26 ******* 42 2022-10-04 07:14 27 ******** 43 2022-10-04 07:15 28 ********* 44 2022-10-04 07:16 29 ********** 45 2022-10-04 07:17 29 ********** 46 2022-10-04 07:18 ? - ... ..( 5 skipped). .. - 52 2022-10-04 07:24 ? - 53 2022-10-04 07:25 28 ********* 54 2022-10-04 07:26 ? - 55 2022-10-04 07:27 28 ********* 56 2022-10-04 07:28 ? - 57 2022-10-04 07:29 25 ****** 58 2022-10-04 07:30 26 ******* 59 2022-10-04 07:31 26 ******* 60 2022-10-04 07:32 27 ******** 61 2022-10-04 07:33 27 ******** 62 2022-10-04 07:34 28 ********* 63 2022-10-04 07:35 28 ********* 64 2022-10-04 07:36 29 ********** 65 2022-10-04 07:37 29 ********** 66 2022-10-04 07:38 30 *********** 67 2022-10-04 07:39 30 *********** 68 2022-10-04 07:40 32 ************* 69 2022-10-04 07:41 33 ************** 70 2022-10-04 07:42 33 ************** 71 2022-10-04 07:43 34 *************** 72 2022-10-04 07:44 35 **************** 73 2022-10-04 07:45 36 ***************** 74 2022-10-04 07:46 37 ****************** 75 2022-10-04 07:47 37 ****************** 76 2022-10-04 07:48 38 ******************* 77 2022-10-04 07:49 38 ******************* 78 2022-10-04 07:50 ? - 79 2022-10-04 07:51 18 - 80 2022-10-04 07:52 19 - 81 2022-10-04 07:53 19 - 82 2022-10-04 07:54 20 * 83 2022-10-04 07:55 22 *** 84 2022-10-04 07:56 23 **** 85 2022-10-04 07:57 25 ****** 86 2022-10-04 07:58 26 ******* 87 2022-10-04 07:59 27 ******** 88 2022-10-04 08:00 28 ********* 89 2022-10-04 08:01 29 ********** 90 2022-10-04 08:02 30 *********** 91 2022-10-04 08:03 30 *********** 92 2022-10-04 08:04 31 ************ 93 2022-10-04 08:05 31 ************ 94 2022-10-04 08:06 32 ************* 95 2022-10-04 08:07 33 ************** 96 2022-10-04 08:08 33 ************** 97 2022-10-04 08:09 34 *************** 98 2022-10-04 08:10 34 *************** 99 2022-10-04 08:11 34 *************** 100 2022-10-04 08:12 35 **************** ... ..( 2 skipped). .. **************** 103 2022-10-04 08:15 35 **************** 104 2022-10-04 08:16 36 ***************** ... ..( 3 skipped). .. ***************** 108 2022-10-04 08:20 36 ***************** 109 2022-10-04 08:21 37 ****************** 110 2022-10-04 08:22 37 ****************** 111 2022-10-04 08:23 36 ***************** 112 2022-10-04 08:24 37 ****************** 113 2022-10-04 08:25 37 ****************** 114 2022-10-04 08:26 37 ****************** 115 2022-10-04 08:27 38 ******************* ... ..( 5 skipped). .. ******************* 121 2022-10-04 08:33 38 ******************* 122 2022-10-04 08:34 39 ******************** 123 2022-10-04 08:35 38 ******************* 124 2022-10-04 08:36 39 ******************** ... ..( 6 skipped). .. ******************** 3 2022-10-04 08:43 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 12360 --- Lifetime Power-On Resets 0x01 0x010 4 16602 --- Power-on Hours 0x01 0x018 6 35138253820 --- Logical Sectors Written 0x01 0x020 6 658468411 --- Number of Write Commands 0x01 0x028 6 76543334669 --- Logical Sectors Read 0x01 0x030 6 1191622301 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 15915 --- Spindle Motor Power-on Hours 0x03 0x010 4 15882 --- Head Flying Hours 0x03 0x018 4 335865 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 9568 --- Read Recovery Attempts 0x03 0x030 4 3 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 8575 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 27545 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 --- Current Temperature 0x05 0x010 1 36 N-- Average Short Term Temperature 0x05 0x018 1 34 N-- Average Long Term Temperature 0x05 0x020 1 59 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 47 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 45 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 39612 --- Number of Hardware Resets 0x06 0x010 4 11875 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 65535+ Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS


Hardware for Linux and BSD

GitHub