/dev/sda smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-25-amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3500413AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: JC45 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Oct 31 09:44:26 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 83) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 105 099 006 - 8091413 3 Spin_Up_Time PO---- 100 100 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 142 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 086 060 030 - 404029398 9 Power_On_Hours -O--CK 068 011 000 - 28704 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 142 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 097 000 - 50 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 061 047 045 - 39 (Min/Max 38/41) 194 Temperature_Celsius -O---K 039 053 000 - 39 (0 12 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 017 014 000 - 8091413 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 107228 (131 139 0) 241 Total_LBAs_Written ------ 100 253 000 - 1723066079 242 Total_LBAs_Read ------ 100 253 000 - 893656196 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 38/41 Celsius Lifetime Min/Max Temperature: 12/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (23) Index Estimated Time Temperature Celsius 24 2023-10-26 05:17 35 **************** ... ..( 2 skipped). .. **************** 27 2023-10-26 08:14 35 **************** 28 2023-10-26 09:13 40 ********************* 29 2023-10-26 10:12 40 ********************* 30 2023-10-26 11:11 40 ********************* 31 2023-10-26 12:10 ? - 32 2023-10-26 13:09 39 ******************** 33 2023-10-26 14:08 39 ******************** 34 2023-10-26 15:07 38 ******************* 35 2023-10-26 16:06 40 ********************* ... ..( 22 skipped). .. ********************* 58 2023-10-27 14:43 40 ********************* 59 2023-10-27 15:42 41 ********************** 60 2023-10-27 16:41 40 ********************* 61 2023-10-27 17:40 40 ********************* 62 2023-10-27 18:39 40 ********************* 63 2023-10-27 19:38 41 ********************** ... ..( 2 skipped). .. ********************** 66 2023-10-27 22:35 41 ********************** 67 2023-10-27 23:34 40 ********************* ... ..( 4 skipped). .. ********************* 72 2023-10-28 04:29 40 ********************* 73 2023-10-28 05:28 39 ******************** ... ..( 9 skipped). .. ******************** 83 2023-10-28 15:18 39 ******************** 84 2023-10-28 16:17 40 ********************* ... ..( 3 skipped). .. ********************* 88 2023-10-28 20:13 40 ********************* 89 2023-10-28 21:12 39 ******************** ... ..( 6 skipped). .. ******************** 96 2023-10-29 03:05 39 ******************** 97 2023-10-29 04:04 38 ******************* 98 2023-10-29 05:03 39 ******************** ... ..( 4 skipped). .. ******************** 103 2023-10-29 09:58 39 ******************** 104 2023-10-29 10:57 38 ******************* 105 2023-10-29 11:56 39 ******************** 106 2023-10-29 12:55 38 ******************* ... ..( 18 skipped). .. ******************* 125 2023-10-30 07:36 38 ******************* 126 2023-10-30 08:35 39 ******************** ... ..( 5 skipped). .. ******************** 4 2023-10-30 14:29 39 ******************** 5 2023-10-30 15:28 40 ********************* ... ..( 14 skipped). .. ********************* 20 2023-10-31 06:13 40 ********************* 21 2023-10-31 07:12 39 ******************** 22 2023-10-31 08:11 39 ******************** 23 2023-10-31 09:10 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-25-amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 3.5 Device Model: ST2000DM006-2DM164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC26 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Oct 31 09:44:26 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 80) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 221) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 099 006 - 182615512 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 47 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 32 7 Seek_Error_Rate POSR-- 082 060 030 - 183168495 9 Power_On_Hours -O--CK 046 046 000 - 47413 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 47 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 063 063 000 - 37 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 043 028 045 NOW 57 (255 255 58 53 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 35 193 Load_Cycle_Count -O--CK 100 100 000 - 190 194 Temperature_Celsius -O---K 057 072 000 - 57 (0 21 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 47414h+41m+31.499s 241 Total_LBAs_Written ------ 100 253 000 - 17960032774 242 Total_LBAs_Read ------ 100 253 000 - 625447328041 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 37 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37 [16] occurred at disk power-on lifetime: 46385 hours (1932 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e3 84 11 80 00 00 Error: UNC at LBA = 0xe3841180 = 3817083264 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 e3 84 11 80 e0 00 00:56:44.219 READ DMA EXT 35 00 00 00 08 00 00 74 49 86 50 e0 00 00:56:44.199 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 08 08 a0 00 00:56:44.161 FLUSH CACHE EXT ca 00 00 00 01 00 00 00 00 08 08 e0 00 00:56:44.161 WRITE DMA ea 00 00 00 00 00 00 00 00 08 17 a0 00 00:56:44.161 FLUSH CACHE EXT Error 36 [15] occurred at disk power-on lifetime: 46385 hours (1932 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e3 84 11 80 00 00 Error: UNC at LBA = 0xe3841180 = 3817083264 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 f0 00 00 e3 84 11 10 e0 00 00:56:40.278 READ DMA EXT 25 00 00 00 08 00 00 e3 84 11 08 e0 00 00:56:40.251 READ DMA EXT 25 00 00 00 08 00 00 32 94 6f d8 e0 00 00:56:40.241 READ DMA EXT 25 00 00 00 08 00 00 32 94 6e d8 e0 00 00:56:40.232 READ DMA EXT 25 00 00 00 08 00 00 32 94 52 58 e0 00 00:56:40.220 READ DMA EXT Error 35 [14] occurred at disk power-on lifetime: 45348 hours (1889 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e7 c3 1c 50 00 00 Error: UNC at LBA = 0xe7c31c50 = 3888323664 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 07 80 00 00 e7 bd 60 80 e0 00 2d+16:29:06.163 READ DMA EXT 25 00 00 05 00 00 00 e7 bd 5b 80 e0 00 2d+16:29:06.129 READ DMA EXT 25 00 00 04 00 00 00 e7 bd 57 80 e0 00 2d+16:29:06.126 READ DMA EXT 25 00 00 03 00 00 00 e7 bd 54 80 e0 00 2d+16:29:06.124 READ DMA EXT 25 00 00 00 80 00 00 e7 bd 54 00 e0 00 2d+16:29:06.124 READ DMA EXT Error 34 [13] occurred at disk power-on lifetime: 43836 hours (1826 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e3 84 0b b0 00 00 Error: UNC at LBA = 0xe3840bb0 = 3817081776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 80 00 00 e3 84 09 80 e0 00 2d+15:36:42.221 READ DMA EXT 25 00 00 05 80 00 00 e3 81 af 80 e0 00 2d+15:36:41.257 READ DMA EXT 25 00 00 04 80 00 00 e3 7f 2c 80 e0 00 2d+15:36:40.424 READ DMA EXT 25 00 00 08 00 00 00 e3 7f 24 80 e0 00 2d+15:36:40.395 READ DMA EXT 25 00 00 07 00 00 00 e3 7f 1d 80 e0 00 2d+15:36:40.391 READ DMA EXT Error 33 [12] occurred at disk power-on lifetime: 38798 hours (1616 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e3 84 10 e0 00 00 Error: UNC at LBA = 0xe38410e0 = 3817083104 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 80 00 00 e3 84 0d 80 e0 00 2d+02:45:13.479 READ DMA EXT 25 00 00 05 00 00 00 e3 84 08 80 e0 00 2d+02:45:13.279 READ DMA EXT 25 00 00 04 00 00 00 e3 7d a4 00 e0 00 2d+02:45:10.989 READ DMA EXT 25 00 00 06 80 00 00 e3 77 8e 00 e0 00 2d+02:45:08.744 READ DMA EXT 25 00 00 07 80 00 00 e3 77 86 80 e0 00 2d+02:45:08.709 READ DMA EXT Error 32 [11] occurred at disk power-on lifetime: 36612 hours (1525 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e3 84 16 30 00 00 Error: UNC at LBA = 0xe3841630 = 3817084464 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 05 00 00 00 e3 84 12 00 e0 00 10d+11:41:32.892 READ DMA EXT 25 00 00 04 80 00 00 e3 84 0d 80 e0 00 10d+11:41:32.853 READ DMA EXT 25 00 00 04 80 00 00 e3 84 09 00 e0 00 10d+11:41:32.748 READ DMA EXT 25 00 00 04 80 00 00 e3 77 6a 00 e0 00 10d+11:41:28.499 READ DMA EXT 25 00 00 04 80 00 00 e3 77 65 80 e0 00 10d+11:41:28.464 READ DMA EXT Error 31 [10] occurred at disk power-on lifetime: 36022 hours (1500 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e3 79 8a 28 00 00 Error: UNC at LBA = 0xe3798a28 = 3816393256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 e3 79 8a 28 e0 00 5d+19:30:08.421 READ DMA EXT 25 00 00 00 08 00 00 e3 79 8a 20 e0 00 5d+19:30:08.419 READ DMA EXT 25 00 00 00 08 00 00 e3 79 8a 18 e0 00 5d+19:30:08.419 READ DMA EXT 25 00 00 00 08 00 00 e3 79 8a 10 e0 00 5d+19:30:08.419 READ DMA EXT 25 00 00 00 08 00 00 e3 79 8a 08 e0 00 5d+19:30:08.419 READ DMA EXT Error 30 [9] occurred at disk power-on lifetime: 36022 hours (1500 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e3 79 8a 28 00 00 Error: UNC at LBA = 0xe3798a28 = 3816393256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 e3 79 8a 00 e0 00 5d+19:30:04.660 READ DMA EXT 25 00 00 00 40 00 00 e3 79 83 00 e0 00 5d+19:30:04.651 READ DMA EXT 25 00 00 00 c0 00 00 e3 79 80 00 e0 00 5d+19:30:04.642 READ DMA EXT 25 00 00 00 80 00 00 e3 79 62 40 e0 00 5d+19:30:04.635 READ DMA EXT 25 00 00 00 80 00 00 e3 79 61 40 e0 00 5d+19:30:04.609 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 57 Celsius Power Cycle Min/Max Temperature: 53/58 Celsius Lifetime Min/Max Temperature: 21/72 Celsius Under/Over Temperature Limit Count: 0/42 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-25-amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 3.5 Device Model: ST2000DM006-2DM164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC26 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Oct 31 09:44:27 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 80) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 211) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 115 099 006 - 89411608 3 Spin_Up_Time PO---- 096 096 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 46 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 081 060 030 - 160320054 9 Power_On_Hours -O--CK 046 046 000 - 47408 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 46 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 099 099 000 - 1 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 097 097 000 - 3 190 Airflow_Temperature_Cel -O---K 046 031 045 Past 54 (255 255 54 50 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 35 193 Load_Cycle_Count -O--CK 100 100 000 - 188 194 Temperature_Celsius -O---K 054 069 000 - 54 (0 21 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 47410h+08m+45.206s 241 Total_LBAs_Written ------ 100 253 000 - 25954574877 242 Total_LBAs_Read ------ 100 253 000 - 319963816374 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 44504 hours (1854 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 e6 04 0a 58 00 00 Error: UNC at LBA = 0xe6040a58 = 3859024472 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 00 00 00 e6 04 0a 00 e0 00 30d+15:41:35.572 READ DMA EXT 25 00 00 04 00 00 00 e6 04 06 00 e0 00 30d+15:41:35.565 READ DMA EXT 25 00 00 00 80 00 00 e6 04 05 80 e0 00 30d+15:41:35.560 READ DMA EXT 25 00 00 04 00 00 00 e6 04 01 80 e0 00 30d+15:41:35.558 READ DMA EXT 25 00 00 06 80 00 00 e5 ff 7e 00 e0 00 30d+15:41:34.062 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 54 Celsius Power Cycle Min/Max Temperature: 50/54 Celsius Lifetime Min/Max Temperature: 21/69 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS