/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT02B6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 265) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 092 092 000 - 39314 12 Power_Cycle_Count -O--CK 099 099 000 - 360 177 Wear_Leveling_Count PO--C- 096 096 000 - 84 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 099 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 065 041 000 - 35 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 001 001 000 - 211118 235 POR_Recovery_Count -O--C- 099 099 000 - 318 241 Total_LBAs_Written -O--CK 099 099 000 - 44833572333 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 34/47 Celsius Lifetime Min/Max Temperature: 10/59 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (83) Index Estimated Time Temperature Celsius 84 2022-12-19 20:20 36 ***************** ... ..( 39 skipped). .. ***************** 124 2022-12-20 03:00 36 ***************** 125 2022-12-20 03:10 37 ****************** 126 2022-12-20 03:20 38 ******************* 127 2022-12-20 03:30 39 ******************** 0 2022-12-20 03:40 38 ******************* 1 2022-12-20 03:50 38 ******************* 2 2022-12-20 04:00 37 ****************** 3 2022-12-20 04:10 37 ****************** 4 2022-12-20 04:20 37 ****************** 5 2022-12-20 04:30 36 ***************** ... ..( 9 skipped). .. ***************** 15 2022-12-20 06:10 36 ***************** 16 2022-12-20 06:20 37 ****************** ... ..( 3 skipped). .. ****************** 20 2022-12-20 07:00 37 ****************** 21 2022-12-20 07:10 36 ***************** ... ..( 3 skipped). .. ***************** 25 2022-12-20 07:50 36 ***************** 26 2022-12-20 08:00 37 ****************** 27 2022-12-20 08:10 37 ****************** 28 2022-12-20 08:20 36 ***************** ... ..( 7 skipped). .. ***************** 36 2022-12-20 09:40 36 ***************** 37 2022-12-20 09:50 37 ****************** ... ..( 3 skipped). .. ****************** 41 2022-12-20 10:30 37 ****************** 42 2022-12-20 10:40 36 ***************** 43 2022-12-20 10:50 36 ***************** 44 2022-12-20 11:00 36 ***************** 45 2022-12-20 11:10 43 ************************ 46 2022-12-20 11:20 47 **************************** 47 2022-12-20 11:30 38 ******************* 48 2022-12-20 11:40 37 ****************** ... ..( 3 skipped). .. ****************** 52 2022-12-20 12:20 37 ****************** 53 2022-12-20 12:30 36 ***************** ... ..( 23 skipped). .. ***************** 77 2022-12-20 16:30 36 ***************** 78 2022-12-20 16:40 37 ****************** 79 2022-12-20 16:50 36 ***************** 80 2022-12-20 17:00 36 ***************** 81 2022-12-20 17:10 35 **************** 82 2022-12-20 17:20 35 **************** 83 2022-12-20 17:30 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 18 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Black Device Model: WDC WD4003FZEX-00Z4SA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (43200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 467) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 186 185 051 - 566 3 Spin_Up_Time POS--K 144 135 021 - 11766 4 Start_Stop_Count -O--CK 098 098 000 - 2938 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 017 017 000 - 61112 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 580 16 Unknown_Attribute -O---K 014 186 000 - 256430574344 192 Power-Off_Retract_Count -O--CK 200 200 000 - 480 193 Load_Cycle_Count -O--CK 200 200 000 - 2457 194 Temperature_Celsius -O---K 105 093 000 - 47 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 4 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 4288 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4288 [15] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 06 f6 0d 30 40 00 Error: UNC at LBA = 0x06f60d30 = 116788528 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 06 f6 0d 30 40 08 1d+11:59:39.099 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 00 e0 08 1d+11:59:39.069 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+11:59:39.069 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 1d+11:59:39.069 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+11:59:39.068 IDENTIFY DEVICE Error 4287 [14] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 06 f6 0d 30 40 00 Error: UNC at LBA = 0x06f60d30 = 116788528 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 06 f6 0d 30 40 08 1d+11:59:36.522 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 00 e0 08 1d+11:59:36.501 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+11:59:36.501 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 1d+11:59:36.501 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+11:59:36.499 IDENTIFY DEVICE Error 4286 [13] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 06 f6 0d 30 40 00 Error: UNC at LBA = 0x06f60d30 = 116788528 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 06 f6 0d 30 40 08 1d+11:59:33.963 READ FPDMA QUEUED 61 00 18 00 10 00 00 00 91 c7 98 40 08 1d+11:59:26.010 WRITE FPDMA QUEUED 61 05 40 00 08 00 00 00 91 c2 58 40 08 1d+11:59:26.010 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 00 64 5b f0 40 08 1d+11:59:26.010 WRITE FPDMA QUEUED 61 00 08 00 f8 00 00 00 64 5b 90 40 08 1d+11:59:26.010 WRITE FPDMA QUEUED Error 4285 [12] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 77 38 70 40 00 Error: UNC at LBA = 0x07773870 = 125253744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 98 00 00 07 77 38 70 40 08 1d+11:59:20.041 READ FPDMA QUEUED b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 1d+11:59:20.038 SMART READ DATA b0 00 d1 00 01 00 00 00 c2 4f 00 00 08 1d+11:59:20.021 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] 47 00 00 00 01 00 00 00 00 00 00 e0 08 1d+11:59:20.020 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+11:59:20.020 SET FEATURES [Enable SATA feature] Error 4284 [11] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 77 38 70 40 00 Error: UNC at LBA = 0x07773870 = 125253744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 07 77 38 70 40 08 1d+11:59:17.473 READ FPDMA QUEUED ec 00 00 00 01 00 00 00 00 00 00 00 08 1d+11:59:17.473 IDENTIFY DEVICE e5 00 00 00 00 00 00 00 00 00 00 00 08 1d+11:59:17.454 CHECK POWER MODE 47 00 00 00 01 00 00 00 00 00 00 e0 08 1d+11:59:17.454 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+11:59:17.454 SET FEATURES [Enable SATA feature] Error 4283 [10] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 77 38 70 40 00 Error: UNC at LBA = 0x07773870 = 125253744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 07 77 38 70 40 08 1d+11:59:14.934 READ FPDMA QUEUED 60 00 08 00 50 00 00 0f 7b fd b0 40 08 1d+11:59:14.926 READ FPDMA QUEUED 60 00 08 00 b0 00 00 0f 7b fe 28 40 08 1d+11:59:14.915 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 00 e0 08 1d+11:59:14.890 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+11:59:14.890 SET FEATURES [Enable SATA feature] Error 4282 [9] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 77 38 70 40 00 Error: UNC at LBA = 0x07773870 = 125253744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 07 77 38 70 40 08 1d+11:59:12.332 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 00 e0 08 1d+11:59:12.331 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+11:59:12.331 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 1d+11:59:12.331 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+11:59:12.331 IDENTIFY DEVICE Error 4281 [8] occurred at disk power-on lifetime: 61098 hours (2545 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 77 38 70 40 00 Error: UNC at LBA = 0x07773870 = 125253744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 07 77 38 70 40 08 1d+11:59:09.802 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 00 e0 08 1d+11:59:09.802 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+11:59:09.802 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 1d+11:59:09.801 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+11:59:09.801 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2495 - # 2 Short offline Completed without error 00% 2252 - # 3 Short offline Completed without error 00% 2171 - # 4 Short offline Completed without error 00% 2062 - # 5 Short offline Completed without error 00% 1705 - # 6 Short offline Completed without error 00% 1513 - # 7 Short offline Completed without error 00% 1506 - # 8 Short offline Completed without error 00% 917 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 47 Celsius Power Cycle Min/Max Temperature: 32/48 Celsius Lifetime Min/Max Temperature: 0/60 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (346) Index Estimated Time Temperature Celsius 347 2022-12-20 09:37 47 **************************** ... ..(476 skipped). .. **************************** 346 2022-12-20 17:34 47 **************************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 21 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 22 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 181092 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Black Device Model: WDC WD4003FZEX-00Z4SA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (44040) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 476) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 179 051 - 29 3 Spin_Up_Time POS--K 234 131 021 - 7275 4 Start_Stop_Count -O--CK 100 100 000 - 155 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 064 064 000 - 26349 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 140 16 Unknown_Attribute -O---K 014 186 000 - 247873715980 192 Power-Off_Retract_Count -O--CK 200 200 000 - 131 193 Load_Cycle_Count -O--CK 200 200 000 - 23 194 Temperature_Celsius -O---K 105 087 000 - 47 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 93 198 Offline_Uncorrectable ----CK 200 200 000 - 91 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 59 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2478 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2478 [5] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b1 d6 10 48 40 00 Error: UNC at LBA = 0xb1d61048 = 2983596104 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 28 00 00 b1 d6 13 c0 40 00 8d+17:56:24.459 READ FPDMA QUEUED 60 01 00 00 20 00 00 b1 d6 12 c0 40 00 8d+17:56:24.459 READ FPDMA QUEUED 60 01 00 00 18 00 00 b1 d6 11 c0 40 00 8d+17:56:24.459 READ FPDMA QUEUED 60 01 00 00 10 00 00 b1 d6 10 c0 40 00 8d+17:56:24.459 READ FPDMA QUEUED 60 01 00 00 08 00 00 b1 d6 0f c0 40 00 8d+17:56:24.459 READ FPDMA QUEUED Error 2477 [4] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b7 eb 52 c0 40 00 Error: WP at LBA = 0xb7eb52c0 = 3085652672 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 d0 00 00 e8 e0 f7 f0 40 00 8d+17:56:21.916 WRITE FPDMA QUEUED 60 01 00 00 c8 00 00 b7 eb 56 58 40 00 8d+17:56:21.916 READ FPDMA QUEUED 60 01 00 00 c0 00 00 b7 eb 55 58 40 00 8d+17:56:21.916 READ FPDMA QUEUED 60 01 00 00 b8 00 00 b7 eb 54 58 40 00 8d+17:56:21.916 READ FPDMA QUEUED 60 01 00 00 b0 00 00 b7 eb 53 58 40 00 8d+17:56:21.916 READ FPDMA QUEUED Error 2476 [3] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b1 d6 10 48 40 00 Error: UNC at LBA = 0xb1d61048 = 2983596104 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 18 00 00 b1 d6 13 c0 40 00 8d+17:56:17.685 READ FPDMA QUEUED 60 01 00 00 10 00 00 b1 d6 12 c0 40 00 8d+17:56:17.685 READ FPDMA QUEUED 60 01 00 00 08 00 00 b1 d6 11 c0 40 00 8d+17:56:17.685 READ FPDMA QUEUED 60 01 00 00 f8 00 00 b1 d6 10 c0 40 00 8d+17:56:17.685 READ FPDMA QUEUED 60 01 00 00 f0 00 00 b1 d6 0f c0 40 00 8d+17:56:17.685 READ FPDMA QUEUED Error 2475 [2] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b7 eb 52 c0 40 00 Error: WP at LBA = 0xb7eb52c0 = 3085652672 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 38 00 00 e8 e0 60 00 40 00 8d+17:56:15.112 WRITE FPDMA QUEUED 60 01 00 00 30 00 00 b7 eb 56 58 40 00 8d+17:56:15.112 READ FPDMA QUEUED 60 01 00 00 28 00 00 b7 eb 55 58 40 00 8d+17:56:15.112 READ FPDMA QUEUED 60 01 00 00 20 00 00 b7 eb 54 58 40 00 8d+17:56:15.112 READ FPDMA QUEUED 60 01 00 00 18 00 00 b7 eb 53 58 40 00 8d+17:56:15.112 READ FPDMA QUEUED Error 2474 [1] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b1 d6 10 48 40 00 Error: UNC at LBA = 0xb1d61048 = 2983596104 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 08 00 00 b1 d6 13 c0 40 00 8d+17:53:55.069 READ FPDMA QUEUED 60 01 00 00 f8 00 00 b1 d6 12 c0 40 00 8d+17:53:55.069 READ FPDMA QUEUED 60 01 00 00 f0 00 00 b1 d6 11 c0 40 00 8d+17:53:55.069 READ FPDMA QUEUED 60 01 00 00 e8 00 00 b1 d6 10 c0 40 00 8d+17:53:55.069 READ FPDMA QUEUED 60 01 00 00 e0 00 00 b1 d6 0f c0 40 00 8d+17:53:55.069 READ FPDMA QUEUED Error 2473 [0] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b7 eb 52 c0 40 00 Error: UNC at LBA = 0xb7eb52c0 = 3085652672 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 60 00 00 b7 eb 56 58 40 00 8d+17:53:52.437 READ FPDMA QUEUED 60 01 00 00 58 00 00 b7 eb 55 58 40 00 8d+17:53:52.437 READ FPDMA QUEUED 60 01 00 00 50 00 00 b7 eb 54 58 40 00 8d+17:53:52.437 READ FPDMA QUEUED 60 01 00 00 48 00 00 b7 eb 53 58 40 00 8d+17:53:52.437 READ FPDMA QUEUED 60 01 00 00 40 00 00 b7 eb 52 58 40 00 8d+17:53:52.437 READ FPDMA QUEUED Error 2472 [23] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b1 d6 10 48 40 00 Error: UNC at LBA = 0xb1d61048 = 2983596104 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 90 00 00 b1 d6 13 c0 40 00 8d+17:51:53.766 READ FPDMA QUEUED 60 01 00 00 88 00 00 b1 d6 12 c0 40 00 8d+17:51:53.766 READ FPDMA QUEUED 60 01 00 00 80 00 00 b1 d6 11 c0 40 00 8d+17:51:53.766 READ FPDMA QUEUED 60 01 00 00 78 00 00 b1 d6 10 c0 40 00 8d+17:51:53.766 READ FPDMA QUEUED 60 01 00 00 70 00 00 b1 d6 0f c0 40 00 8d+17:51:53.766 READ FPDMA QUEUED Error 2471 [22] occurred at disk power-on lifetime: 26271 hours (1094 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 b7 eb 52 c0 40 00 Error: UNC at LBA = 0xb7eb52c0 = 3085652672 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 98 00 00 b7 eb 56 58 40 00 8d+17:51:51.162 READ FPDMA QUEUED 60 01 00 00 90 00 00 b7 eb 55 58 40 00 8d+17:51:51.162 READ FPDMA QUEUED 60 01 00 00 88 00 00 b7 eb 54 58 40 00 8d+17:51:51.162 READ FPDMA QUEUED 60 01 00 00 80 00 00 b7 eb 53 58 40 00 8d+17:51:51.162 READ FPDMA QUEUED 60 01 00 00 78 00 00 b7 eb 52 58 40 00 8d+17:51:51.162 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 47 Celsius Power Cycle Min/Max Temperature: 46/48 Celsius Lifetime Min/Max Temperature: 0/65 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (381) Index Estimated Time Temperature Celsius 382 2022-12-20 09:37 47 **************************** ... ..( 55 skipped). .. **************************** 438 2022-12-20 10:33 47 **************************** 439 2022-12-20 10:34 46 *************************** ... ..( 57 skipped). .. *************************** 19 2022-12-20 11:32 46 *************************** 20 2022-12-20 11:33 47 **************************** ... ..(360 skipped). .. **************************** 381 2022-12-20 17:34 47 **************************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 18 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 19 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 181098 Vendor specific /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 870 QVO 1TB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVQ02B6Q User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 3080 12 Power_Cycle_Count -O--CK 099 099 000 - 39 177 Wear_Leveling_Count PO--C- 098 098 000 - 15 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 061 045 000 - 39 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 1 235 POR_Recovery_Count -O--C- 099 099 000 - 24 241 Total_LBAs_Written -O--CK 099 099 000 - 24531341075 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 35/51 Celsius Lifetime Min/Max Temperature: 18/55 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (59) Index Estimated Time Temperature Celsius 60 2022-12-19 20:20 38 ******************* 61 2022-12-19 20:30 38 ******************* 62 2022-12-19 20:40 38 ******************* 63 2022-12-19 20:50 39 ******************** 64 2022-12-19 21:00 38 ******************* ... ..( 23 skipped). .. ******************* 88 2022-12-20 01:00 38 ******************* 89 2022-12-20 01:10 50 ******************************* 90 2022-12-20 01:20 47 **************************** 91 2022-12-20 01:30 39 ******************** 92 2022-12-20 01:40 38 ******************* ... ..( 19 skipped). .. ******************* 112 2022-12-20 05:00 38 ******************* 113 2022-12-20 05:10 39 ******************** 114 2022-12-20 05:20 38 ******************* ... ..( 5 skipped). .. ******************* 120 2022-12-20 06:20 38 ******************* 121 2022-12-20 06:30 39 ******************** 122 2022-12-20 06:40 38 ******************* ... ..( 3 skipped). .. ******************* 126 2022-12-20 07:20 38 ******************* 127 2022-12-20 07:30 39 ******************** 0 2022-12-20 07:40 39 ******************** 1 2022-12-20 07:50 41 ********************** ... ..( 2 skipped). .. ********************** 4 2022-12-20 08:20 41 ********************** 5 2022-12-20 08:30 40 ********************* 6 2022-12-20 08:40 40 ********************* 7 2022-12-20 08:50 40 ********************* 8 2022-12-20 09:00 41 ********************** ... ..( 8 skipped). .. ********************** 17 2022-12-20 10:30 41 ********************** 18 2022-12-20 10:40 40 ********************* 19 2022-12-20 10:50 41 ********************** 20 2022-12-20 11:00 41 ********************** 21 2022-12-20 11:10 41 ********************** 22 2022-12-20 11:20 37 ****************** 23 2022-12-20 11:30 39 ******************** 24 2022-12-20 11:40 38 ******************* ... ..( 3 skipped). .. ******************* 28 2022-12-20 12:20 38 ******************* 29 2022-12-20 12:30 40 ********************* 30 2022-12-20 12:40 41 ********************** 31 2022-12-20 12:50 41 ********************** 32 2022-12-20 13:00 40 ********************* 33 2022-12-20 13:10 41 ********************** 34 2022-12-20 13:20 41 ********************** 35 2022-12-20 13:30 41 ********************** 36 2022-12-20 13:40 40 ********************* 37 2022-12-20 13:50 41 ********************** 38 2022-12-20 14:00 39 ******************** 39 2022-12-20 14:10 41 ********************** 40 2022-12-20 14:20 40 ********************* 41 2022-12-20 14:30 41 ********************** 42 2022-12-20 14:40 40 ********************* 43 2022-12-20 14:50 41 ********************** 44 2022-12-20 15:00 41 ********************** 45 2022-12-20 15:10 40 ********************* 46 2022-12-20 15:20 39 ******************** 47 2022-12-20 15:30 38 ******************* 48 2022-12-20 15:40 38 ******************* 49 2022-12-20 15:50 41 ********************** 50 2022-12-20 16:00 38 ******************* 51 2022-12-20 16:10 38 ******************* 52 2022-12-20 16:20 39 ******************** 53 2022-12-20 16:30 42 *********************** 54 2022-12-20 16:40 38 ******************* 55 2022-12-20 16:50 37 ****************** 56 2022-12-20 17:00 38 ******************* ... ..( 2 skipped). .. ******************* 59 2022-12-20 17:30 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 39 --- Lifetime Power-On Resets 0x01 0x010 4 3080 --- Power-on Hours 0x01 0x018 6 24531341075 --- Logical Sectors Written 0x01 0x020 6 479246880 --- Number of Write Commands 0x01 0x028 6 15413695830 --- Logical Sectors Read 0x01 0x030 6 195435338 --- Number of Read Commands 0x01 0x038 6 1800000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 --- Current Temperature 0x05 0x020 1 55 --- Highest Temperature 0x05 0x028 1 18 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1105 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 1 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 22 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 22 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdf smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD30EZRX-00MMMB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (50700) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 487) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 151 138 021 - 9408 4 Start_Stop_Count -O--CK 090 090 000 - 10629 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 001 001 000 - 75505 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 342 192 Power-Off_Retract_Count -O--CK 200 200 000 - 287 193 Load_Cycle_Count -O--CK 031 031 000 - 507169 194 Temperature_Celsius -O---K 117 096 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 14/46 Celsius Lifetime Min/Max Temperature: 14/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (39) Index Estimated Time Temperature Celsius 40 2022-12-20 09:37 30 *********** ... ..( 12 skipped). .. *********** 53 2022-12-20 09:50 30 *********** 54 2022-12-20 09:51 29 ********** ... ..( 3 skipped). .. ********** 58 2022-12-20 09:55 29 ********** 59 2022-12-20 09:56 ? - 60 2022-12-20 09:57 29 ********** 61 2022-12-20 09:58 30 *********** ... ..( 4 skipped). .. *********** 66 2022-12-20 10:03 30 *********** 67 2022-12-20 10:04 31 ************ 68 2022-12-20 10:05 31 ************ 69 2022-12-20 10:06 32 ************* ... ..( 2 skipped). .. ************* 72 2022-12-20 10:09 32 ************* 73 2022-12-20 10:10 33 ************** ... ..( 5 skipped). .. ************** 79 2022-12-20 10:16 33 ************** 80 2022-12-20 10:17 34 *************** ... ..( 4 skipped). .. *************** 85 2022-12-20 10:22 34 *************** 86 2022-12-20 10:23 35 **************** ... ..( 5 skipped). .. **************** 92 2022-12-20 10:29 35 **************** 93 2022-12-20 10:30 36 ***************** 94 2022-12-20 10:31 36 ***************** 95 2022-12-20 10:32 36 ***************** 96 2022-12-20 10:33 35 **************** ... ..( 3 skipped). .. **************** 100 2022-12-20 10:37 35 **************** 101 2022-12-20 10:38 34 *************** ... ..( 3 skipped). .. *************** 105 2022-12-20 10:42 34 *************** 106 2022-12-20 10:43 ? - 107 2022-12-20 10:44 34 *************** 108 2022-12-20 10:45 33 ************** 109 2022-12-20 10:46 34 *************** 110 2022-12-20 10:47 33 ************** 111 2022-12-20 10:48 34 *************** 112 2022-12-20 10:49 34 *************** 113 2022-12-20 10:50 34 *************** 114 2022-12-20 10:51 35 **************** ... ..( 3 skipped). .. **************** 118 2022-12-20 10:55 35 **************** 119 2022-12-20 10:56 36 ***************** 120 2022-12-20 10:57 35 **************** ... ..( 7 skipped). .. **************** 128 2022-12-20 11:05 35 **************** 129 2022-12-20 11:06 36 ***************** ... ..( 4 skipped). .. ***************** 134 2022-12-20 11:11 36 ***************** 135 2022-12-20 11:12 35 **************** ... ..( 2 skipped). .. **************** 138 2022-12-20 11:15 35 **************** 139 2022-12-20 11:16 34 *************** 140 2022-12-20 11:17 34 *************** 141 2022-12-20 11:18 ? - 142 2022-12-20 11:19 34 *************** 143 2022-12-20 11:20 35 **************** 144 2022-12-20 11:21 29 ********** ... ..( 79 skipped). .. ********** 224 2022-12-20 12:41 29 ********** 225 2022-12-20 12:42 ? - 226 2022-12-20 12:43 29 ********** 227 2022-12-20 12:44 30 *********** ... ..( 2 skipped). .. *********** 230 2022-12-20 12:47 30 *********** 231 2022-12-20 12:48 31 ************ 232 2022-12-20 12:49 31 ************ 233 2022-12-20 12:50 31 ************ 234 2022-12-20 12:51 32 ************* ... ..( 4 skipped). .. ************* 239 2022-12-20 12:56 32 ************* 240 2022-12-20 12:57 33 ************** 241 2022-12-20 12:58 33 ************** 242 2022-12-20 12:59 33 ************** 243 2022-12-20 13:00 ? - 244 2022-12-20 13:01 34 *************** ... ..( 5 skipped). .. *************** 250 2022-12-20 13:07 34 *************** 251 2022-12-20 13:08 35 **************** ... ..( 12 skipped). .. **************** 264 2022-12-20 13:21 35 **************** 265 2022-12-20 13:22 36 ***************** ... ..( 9 skipped). .. ***************** 275 2022-12-20 13:32 36 ***************** 276 2022-12-20 13:33 37 ****************** ... ..( 18 skipped). .. ****************** 295 2022-12-20 13:52 37 ****************** 296 2022-12-20 13:53 38 ******************* 297 2022-12-20 13:54 37 ****************** 298 2022-12-20 13:55 37 ****************** 299 2022-12-20 13:56 38 ******************* ... ..( 87 skipped). .. ******************* 387 2022-12-20 15:24 38 ******************* 388 2022-12-20 15:25 37 ****************** 389 2022-12-20 15:26 37 ****************** 390 2022-12-20 15:27 37 ****************** 391 2022-12-20 15:28 36 ***************** ... ..( 6 skipped). .. ***************** 398 2022-12-20 15:35 36 ***************** 399 2022-12-20 15:36 35 **************** ... ..( 2 skipped). .. **************** 402 2022-12-20 15:39 35 **************** 403 2022-12-20 15:40 34 *************** ... ..( 2 skipped). .. *************** 406 2022-12-20 15:43 34 *************** 407 2022-12-20 15:44 33 ************** 408 2022-12-20 15:45 34 *************** 409 2022-12-20 15:46 33 ************** ... ..( 10 skipped). .. ************** 420 2022-12-20 15:57 33 ************** 421 2022-12-20 15:58 32 ************* ... ..( 7 skipped). .. ************* 429 2022-12-20 16:06 32 ************* 430 2022-12-20 16:07 31 ************ ... ..( 11 skipped). .. ************ 442 2022-12-20 16:19 31 ************ 443 2022-12-20 16:20 30 *********** 444 2022-12-20 16:21 30 *********** 445 2022-12-20 16:22 30 *********** 446 2022-12-20 16:23 31 ************ 447 2022-12-20 16:24 31 ************ 448 2022-12-20 16:25 30 *********** ... ..( 68 skipped). .. *********** 39 2022-12-20 17:34 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 42 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 7365424 Vendor specific /dev/sdg smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD40NDZW-11A8JS0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 4,000,753,475,584 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11760) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 345) minutes. SCT capabilities: (0x30b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 253 253 021 - 4791 4 Start_Stop_Count -O--CK 099 099 000 - 1490 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 095 095 000 - 3970 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 86 192 Power-Off_Retract_Count -O--CK 200 200 000 - 51 193 Load_Cycle_Count -O--CK 194 194 000 - 19926 194 Temperature_Celsius -O---K 115 094 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 289 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 82 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xcf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 31/49 Celsius Lifetime Min/Max Temperature: 19/58 Celsius Specified Max Operating Temperature: 38 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (62) Index Estimated Time Temperature Celsius 63 2022-12-20 15:27 33 ************** ... ..( 4 skipped). .. ************** 68 2022-12-20 15:32 33 ************** 69 2022-12-20 15:33 32 ************* ... ..( 36 skipped). .. ************* 106 2022-12-20 16:10 32 ************* 107 2022-12-20 16:11 ? - 108 2022-12-20 16:12 32 ************* ... ..( 2 skipped). .. ************* 111 2022-12-20 16:15 32 ************* 112 2022-12-20 16:16 33 ************** ... ..( 4 skipped). .. ************** 117 2022-12-20 16:21 33 ************** 118 2022-12-20 16:22 34 *************** 119 2022-12-20 16:23 ? - 120 2022-12-20 16:24 34 *************** ... ..( 6 skipped). .. *************** 127 2022-12-20 16:31 34 *************** 0 2022-12-20 16:32 35 **************** ... ..( 8 skipped). .. **************** 9 2022-12-20 16:41 35 **************** 10 2022-12-20 16:42 36 ***************** ... ..( 13 skipped). .. ***************** 24 2022-12-20 16:56 36 ***************** 25 2022-12-20 16:57 37 ****************** 26 2022-12-20 16:58 ? - 27 2022-12-20 16:59 37 ****************** 28 2022-12-20 17:00 37 ****************** 29 2022-12-20 17:01 ? - 30 2022-12-20 17:02 37 ****************** ... ..( 31 skipped). .. ****************** 62 2022-12-20 17:34 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 48 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 50 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 181090 Vendor specific /dev/sdh smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 Device Model: ST2000DM008-2FR102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 203) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 077 064 006 - 223159120 3 Spin_Up_Time PO---- 098 098 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 9760 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 077 060 045 - 45440543 9 Power_On_Hours -O--CK 068 068 000 - 28867 (66 178 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 61 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 098 000 - 3 3 15 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 066 052 040 - 34 (Min/Max 14/45) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 15 193 Load_Cycle_Count -O--CK 083 083 000 - 35032 194 Temperature_Celsius -O---K 034 048 000 - 34 (0 14 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 083 064 000 - 223159120 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 970h+20m+47.757s 241 Total_LBAs_Written ------ 100 253 000 - 18866078663 242 Total_LBAs_Read ------ 100 253 000 - 11655720718 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 24 Device vendor specific log 0xa2 GPL VS 8160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 9048 Device vendor specific log 0xbd GPL VS 8 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 16 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 24 Device vendor specific log 0xd1 GPL VS 264 Device vendor specific log 0xd3 GPL VS 1920 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 13/45 Celsius Lifetime Min/Max Temperature: 12/48 Celsius Under/Over Temperature Limit Count: 3/0 SCT Temperature History Version: 2 Temperature Sampling Period: 3 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2022-12-15 12:17 30 *********** ... ..( 3 skipped). .. *********** 51 2022-12-15 16:13 30 *********** 52 2022-12-15 17:12 31 ************ ... ..( 6 skipped). .. ************ 59 2022-12-16 00:05 31 ************ 60 2022-12-16 01:04 32 ************* ... ..( 8 skipped). .. ************* 69 2022-12-16 09:55 32 ************* 70 2022-12-16 10:54 33 ************** 71 2022-12-16 11:53 31 ************ 72 2022-12-16 12:52 30 *********** 73 2022-12-16 13:51 31 ************ ... ..( 6 skipped). .. ************ 80 2022-12-16 20:44 31 ************ 81 2022-12-16 21:43 41 ********************** 82 2022-12-16 22:42 43 ************************ 83 2022-12-16 23:41 42 *********************** 84 2022-12-17 00:40 43 ************************ 85 2022-12-17 01:39 40 ********************* 86 2022-12-17 02:38 33 ************** 87 2022-12-17 03:37 32 ************* 88 2022-12-17 04:36 31 ************ 89 2022-12-17 05:35 36 ***************** 90 2022-12-17 06:34 32 ************* 91 2022-12-17 07:33 31 ************ 92 2022-12-17 08:32 32 ************* 93 2022-12-17 09:31 44 ************************* 94 2022-12-17 10:30 44 ************************* 95 2022-12-17 11:29 34 *************** 96 2022-12-17 12:28 33 ************** 97 2022-12-17 13:27 37 ****************** 98 2022-12-17 14:26 36 ***************** 99 2022-12-17 15:25 34 *************** 100 2022-12-17 16:24 35 **************** 101 2022-12-17 17:23 34 *************** 102 2022-12-17 18:22 39 ******************** 103 2022-12-17 19:21 32 ************* 104 2022-12-17 20:20 31 ************ ... ..( 6 skipped). .. ************ 111 2022-12-18 03:13 31 ************ 112 2022-12-18 04:12 32 ************* 113 2022-12-18 05:11 33 ************** 114 2022-12-18 06:10 32 ************* ... ..( 2 skipped). .. ************* 117 2022-12-18 09:07 32 ************* 118 2022-12-18 10:06 31 ************ ... ..( 5 skipped). .. ************ 124 2022-12-18 16:00 31 ************ 125 2022-12-18 16:59 33 ************** 126 2022-12-18 17:58 34 *************** 127 2022-12-18 18:57 35 **************** 0 2022-12-18 19:56 35 **************** 1 2022-12-18 20:55 34 *************** 2 2022-12-18 21:54 32 ************* 3 2022-12-18 22:53 33 ************** 4 2022-12-18 23:52 32 ************* ... ..( 7 skipped). .. ************* 12 2022-12-19 07:44 32 ************* 13 2022-12-19 08:43 31 ************ 14 2022-12-19 09:42 30 *********** ... ..( 6 skipped). .. *********** 21 2022-12-19 16:35 30 *********** 22 2022-12-19 17:34 31 ************ 23 2022-12-19 18:33 30 *********** 24 2022-12-19 19:32 31 ************ 25 2022-12-19 20:31 30 *********** 26 2022-12-19 21:30 31 ************ ... ..( 8 skipped). .. ************ 35 2022-12-20 06:21 31 ************ 36 2022-12-20 07:20 35 **************** 37 2022-12-20 08:19 31 ************ 38 2022-12-20 09:18 30 *********** 39 2022-12-20 10:17 30 *********** 40 2022-12-20 11:16 30 *********** 41 2022-12-20 12:15 35 **************** 42 2022-12-20 13:14 31 ************ 43 2022-12-20 14:13 30 *********** 44 2022-12-20 15:12 32 ************* 45 2022-12-20 16:11 31 ************ 46 2022-12-20 17:10 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 61 --- Lifetime Power-On Resets 0x01 0x010 4 28867 --- Power-on Hours 0x01 0x018 6 18889906431 --- Logical Sectors Written 0x01 0x020 6 25937119 --- Number of Write Commands 0x01 0x028 6 11634993351 --- Logical Sectors Read 0x01 0x030 6 44894494 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 2876 --- Spindle Motor Power-on Hours 0x03 0x010 4 973 --- Head Flying Hours 0x03 0x018 4 35032 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 4 --- Read Recovery Attempts 0x03 0x030 4 14 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 14 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 4 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 15 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 34 --- Current Temperature 0x05 0x010 1 30 --- Average Short Term Temperature 0x05 0x018 1 31 --- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 40 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 33 --- Highest Average Long Term Temperature 0x05 0x048 1 28 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 1676 --- Time in Under-Temperature 0x05 0x068 1 13 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 340 --- Number of Hardware Resets 0x06 0x010 4 134 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdi smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-56-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD30EZRZ-00GXCB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Dec 20 17:34:56 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (32220) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 343) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 233 164 021 - 3325 4 Start_Stop_Count -O--CK 090 090 000 - 10533 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 092 092 000 - 5906 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 090 090 000 - 10530 192 Power-Off_Retract_Count -O--CK 200 200 000 - 11 193 Load_Cycle_Count -O--CK 189 189 000 - 33045 194 Temperature_Celsius -O---K 113 097 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 56 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 36/37 Celsius Lifetime Min/Max Temperature: 7/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (58) Index Estimated Time Temperature Celsius 59 2022-12-20 09:37 29 ********** ... ..( 2 skipped). .. ********** 62 2022-12-20 09:40 29 ********** 63 2022-12-20 09:41 30 *********** ... ..( 3 skipped). .. *********** 67 2022-12-20 09:45 30 *********** 68 2022-12-20 09:46 31 ************ ... ..( 3 skipped). .. ************ 72 2022-12-20 09:50 31 ************ 73 2022-12-20 09:51 32 ************* ... ..( 4 skipped). .. ************* 78 2022-12-20 09:56 32 ************* 79 2022-12-20 09:57 33 ************** ... ..( 2 skipped). .. ************** 82 2022-12-20 10:00 33 ************** 83 2022-12-20 10:01 ? - 84 2022-12-20 10:02 28 ********* ... ..( 2 skipped). .. ********* 87 2022-12-20 10:05 28 ********* 88 2022-12-20 10:06 29 ********** 89 2022-12-20 10:07 29 ********** 90 2022-12-20 10:08 30 *********** 91 2022-12-20 10:09 30 *********** 92 2022-12-20 10:10 31 ************ 93 2022-12-20 10:11 31 ************ 94 2022-12-20 10:12 31 ************ 95 2022-12-20 10:13 32 ************* ... ..( 2 skipped). .. ************* 98 2022-12-20 10:16 32 ************* 99 2022-12-20 10:17 33 ************** ... ..( 4 skipped). .. ************** 104 2022-12-20 10:22 33 ************** 105 2022-12-20 10:23 34 *************** ... ..( 7 skipped). .. *************** 113 2022-12-20 10:31 34 *************** 114 2022-12-20 10:32 35 **************** ... ..( 8 skipped). .. **************** 123 2022-12-20 10:41 35 **************** 124 2022-12-20 10:42 36 ***************** ... ..( 5 skipped). .. ***************** 130 2022-12-20 10:48 36 ***************** 131 2022-12-20 10:49 ? - 132 2022-12-20 10:50 32 ************* ... ..( 3 skipped). .. ************* 136 2022-12-20 10:54 32 ************* 137 2022-12-20 10:55 33 ************** ... ..( 4 skipped). .. ************** 142 2022-12-20 11:00 33 ************** 143 2022-12-20 11:01 34 *************** ... ..( 6 skipped). .. *************** 150 2022-12-20 11:08 34 *************** 151 2022-12-20 11:09 35 **************** ... ..( 7 skipped). .. **************** 159 2022-12-20 11:17 35 **************** 160 2022-12-20 11:18 36 ***************** ... ..( 3 skipped). .. ***************** 164 2022-12-20 11:22 36 ***************** 165 2022-12-20 11:23 ? - 166 2022-12-20 11:24 27 ******** 167 2022-12-20 11:25 ? - 168 2022-12-20 11:26 27 ******** 169 2022-12-20 11:27 ? - 170 2022-12-20 11:28 28 ********* ... ..( 3 skipped). .. ********* 174 2022-12-20 11:32 28 ********* 175 2022-12-20 11:33 29 ********** ... ..( 2 skipped). .. ********** 178 2022-12-20 11:36 29 ********** 179 2022-12-20 11:37 30 *********** ... ..( 2 skipped). .. *********** 182 2022-12-20 11:40 30 *********** 183 2022-12-20 11:41 31 ************ 184 2022-12-20 11:42 ? - 185 2022-12-20 11:43 31 ************ 186 2022-12-20 11:44 31 ************ 187 2022-12-20 11:45 ? - 188 2022-12-20 11:46 32 ************* ... ..( 7 skipped). .. ************* 196 2022-12-20 11:54 32 ************* 197 2022-12-20 11:55 33 ************** ... ..( 4 skipped). .. ************** 202 2022-12-20 12:00 33 ************** 203 2022-12-20 12:01 34 *************** ... ..( 7 skipped). .. *************** 211 2022-12-20 12:09 34 *************** 212 2022-12-20 12:10 35 **************** ... ..( 7 skipped). .. **************** 220 2022-12-20 12:18 35 **************** 221 2022-12-20 12:19 ? - 222 2022-12-20 12:20 27 ******** 223 2022-12-20 12:21 ? - 224 2022-12-20 12:22 27 ******** 225 2022-12-20 12:23 ? - 226 2022-12-20 12:24 28 ********* ... ..( 4 skipped). .. ********* 231 2022-12-20 12:29 28 ********* 232 2022-12-20 12:30 29 ********** ... ..( 2 skipped). .. ********** 235 2022-12-20 12:33 29 ********** 236 2022-12-20 12:34 30 *********** 237 2022-12-20 12:35 ? - 238 2022-12-20 12:36 31 ************ ... ..( 6 skipped). .. ************ 245 2022-12-20 12:43 31 ************ 246 2022-12-20 12:44 32 ************* ... ..( 5 skipped). .. ************* 252 2022-12-20 12:50 32 ************* 253 2022-12-20 12:51 33 ************** ... ..( 4 skipped). .. ************** 258 2022-12-20 12:56 33 ************** 259 2022-12-20 12:57 34 *************** ... ..( 8 skipped). .. *************** 268 2022-12-20 13:06 34 *************** 269 2022-12-20 13:07 35 **************** 270 2022-12-20 13:08 35 **************** 271 2022-12-20 13:09 ? - 272 2022-12-20 13:10 36 ***************** 273 2022-12-20 13:11 ? - 274 2022-12-20 13:12 35 **************** 275 2022-12-20 13:13 ? - 276 2022-12-20 13:14 36 ***************** ... ..( 18 skipped). .. ***************** 295 2022-12-20 13:33 36 ***************** 296 2022-12-20 13:34 37 ****************** ... ..( 11 skipped). .. ****************** 308 2022-12-20 13:46 37 ****************** 309 2022-12-20 13:47 36 ***************** ... ..( 7 skipped). .. ***************** 317 2022-12-20 13:55 36 ***************** 318 2022-12-20 13:56 37 ****************** ... ..( 9 skipped). .. ****************** 328 2022-12-20 14:06 37 ****************** 329 2022-12-20 14:07 ? - 330 2022-12-20 14:08 38 ******************* 331 2022-12-20 14:09 38 ******************* 332 2022-12-20 14:10 ? - 333 2022-12-20 14:11 38 ******************* ... ..( 30 skipped). .. ******************* 364 2022-12-20 14:42 38 ******************* 365 2022-12-20 14:43 ? - 366 2022-12-20 14:44 35 **************** ... ..( 12 skipped). .. **************** 379 2022-12-20 14:57 35 **************** 380 2022-12-20 14:58 36 ***************** ... ..( 9 skipped). .. ***************** 390 2022-12-20 15:08 36 ***************** 391 2022-12-20 15:09 37 ****************** ... ..( 5 skipped). .. ****************** 397 2022-12-20 15:15 37 ****************** 398 2022-12-20 15:16 ? - 399 2022-12-20 15:17 36 ***************** ... ..( 5 skipped). .. ***************** 405 2022-12-20 15:23 36 ***************** 406 2022-12-20 15:24 37 ****************** ... ..( 17 skipped). .. ****************** 424 2022-12-20 15:42 37 ****************** 425 2022-12-20 15:43 38 ******************* ... ..( 19 skipped). .. ******************* 445 2022-12-20 16:03 38 ******************* 446 2022-12-20 16:04 ? - 447 2022-12-20 16:05 28 ********* 448 2022-12-20 16:06 28 ********* 449 2022-12-20 16:07 28 ********* 450 2022-12-20 16:08 29 ********** 451 2022-12-20 16:09 29 ********** 452 2022-12-20 16:10 30 *********** 453 2022-12-20 16:11 30 *********** 454 2022-12-20 16:12 30 *********** 455 2022-12-20 16:13 31 ************ 456 2022-12-20 16:14 31 ************ 457 2022-12-20 16:15 32 ************* ... ..( 2 skipped). .. ************* 460 2022-12-20 16:18 32 ************* 461 2022-12-20 16:19 33 ************** ... ..( 3 skipped). .. ************** 465 2022-12-20 16:23 33 ************** 466 2022-12-20 16:24 34 *************** ... ..( 6 skipped). .. *************** 473 2022-12-20 16:31 34 *************** 474 2022-12-20 16:32 35 **************** ... ..( 8 skipped). .. **************** 5 2022-12-20 16:41 35 **************** 6 2022-12-20 16:42 36 ***************** ... ..( 8 skipped). .. ***************** 15 2022-12-20 16:51 36 ***************** 16 2022-12-20 16:52 ? - 17 2022-12-20 16:53 27 ******** 18 2022-12-20 16:54 27 ******** 19 2022-12-20 16:55 28 ********* ... ..( 2 skipped). .. ********* 22 2022-12-20 16:58 28 ********* 23 2022-12-20 16:59 29 ********** ... ..( 2 skipped). .. ********** 26 2022-12-20 17:02 29 ********** 27 2022-12-20 17:03 30 *********** ... ..( 2 skipped). .. *********** 30 2022-12-20 17:06 30 *********** 31 2022-12-20 17:07 31 ************ ... ..( 4 skipped). .. ************ 36 2022-12-20 17:12 31 ************ 37 2022-12-20 17:13 32 ************* ... ..( 3 skipped). .. ************* 41 2022-12-20 17:17 32 ************* 42 2022-12-20 17:18 33 ************** ... ..( 6 skipped). .. ************** 49 2022-12-20 17:25 33 ************** 50 2022-12-20 17:26 ? - 51 2022-12-20 17:27 27 ******** ... ..( 3 skipped). .. ******** 55 2022-12-20 17:31 27 ******** 56 2022-12-20 17:32 28 ********* 57 2022-12-20 17:33 28 ********* 58 2022-12-20 17:34 28 ********* SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 10530 --- Lifetime Power-On Resets 0x01 0x010 4 5906 --- Power-on Hours 0x01 0x018 6 70467140554 --- Logical Sectors Written 0x01 0x020 6 410511123 --- Number of Write Commands 0x01 0x028 6 30576376623 --- Logical Sectors Read 0x01 0x030 6 340005734 --- Number of Read Commands 0x01 0x038 6 4081730816 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 5886 --- Spindle Motor Power-on Hours 0x03 0x010 4 810 --- Head Flying Hours 0x03 0x018 4 33057 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 11 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 196629 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 38 --- Current Temperature 0x05 0x010 1 38 --- Average Short Term Temperature 0x05 0x018 1 37 --- Average Long Term Temperature 0x05 0x020 1 53 --- Highest Temperature 0x05 0x028 1 12 --- Lowest Temperature 0x05 0x030 1 46 --- Highest Average Short Term Temperature 0x05 0x038 1 29 --- Lowest Average Short Term Temperature 0x05 0x040 1 37 --- Highest Average Long Term Temperature 0x05 0x048 1 33 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 10599 --- Number of Hardware Resets 0x06 0x010 4 112 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1947 Vendor specific