/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-84-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: KINGSTON SA400S37480G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: SBFKK1B3 User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Sep 19 13:58:25 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x00) Offline data collection not supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 738 12 Power_Cycle_Count -O--CK 100 100 000 - 296 148 Unknown_Attribute ------ 100 100 000 - 0 149 Unknown_Attribute ------ 100 100 000 - 0 167 Write_Protect_Mode ------ 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 169 Bad_Block_Rate ------ 100 100 000 - 9 170 Bad_Blk_Ct_Erl/Lat ------ 100 100 010 - 0/9 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 MaxAvgErase_Ct ------ 100 100 000 - 24 (Average 18) 181 Program_Fail_Count -O--CK 100 100 000 - 0 182 Erase_Fail_Count ------ 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 10 194 Temperature_Celsius -O---K 044 055 000 - 44 (Min/Max 19/55) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0 218 CRC_Error_Count -O--CK 100 100 000 - 10 231 SSD_Life_Left ------ 098 098 000 - 98 233 Flash_Writes_GiB -O--CK 100 100 000 - 3193 241 Lifetime_Writes_GiB -O--CK 100 100 000 - 2994 242 Lifetime_Reads_GiB -O--CK 100 100 000 - 4863 244 Average_Erase_Count ------ 100 100 000 - 18 245 Max_Erase_Count ------ 100 100 000 - 24 246 Total_Erase_Count ------ 100 100 000 - 201936 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 10 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [9] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 10 00 00 00 00 00 01 e0 00 Error: ICRC, ABRT 16 sectors at LBA = 0x00000001 = 1 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 10 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT 35 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 WRITE DMA EXT Error 9 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 10 00 00 00 00 00 01 e0 00 Error: ICRC, ABRT 16 sectors at LBA = 0x00000001 = 1 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT 35 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 WRITE DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT Error 8 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 37 e4 36 af e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x37e436af = 937703087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 37 e4 36 af e0 00 00:00:00.000 READ DMA EXT ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:00.000 SET FEATURES [Set transfer mode] ff 00 d5 00 01 00 00 00 00 00 01 00 04 00:00:00.000 [VENDOR SPECIFIC] 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT Error 7 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 20 00 00 00 00 00 02 e0 00 Error: ICRC, ABRT 32 sectors at LBA = 0x00000002 = 2 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT Error 6 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:00.000 SET FEATURES [Set transfer mode] ff 00 d5 00 01 00 00 00 00 00 01 00 04 00:00:00.000 [VENDOR SPECIFIC] 25 00 00 00 20 00 00 37 e4 36 8f e0 00 00:00:00.000 READ DMA EXT Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 20 00 00 37 e4 36 8f e0 00 Error: ICRC, ABRT 32 sectors at LBA = 0x37e4368f = 937703055 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 37 e4 36 8f e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 37 e4 36 af e0 00 00:00:00.000 READ DMA EXT ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:00.000 SET FEATURES [Set transfer mode] ff 00 d5 00 01 00 00 00 00 00 01 00 04 00:00:00.000 [VENDOR SPECIFIC] 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:00:00.000 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 20 00 00 00 00 00 02 e0 00 Error: ICRC, ABRT 32 sectors at LBA = 0x00000002 = 2 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 01 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:00.000 SET FEATURES [Set transfer mode] Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.000 READ DMA EXT ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:00:00.000 SET FEATURES [Set transfer mode] ff 00 d5 00 01 00 00 00 00 00 01 00 04 00:00:00.000 [VENDOR SPECIFIC] 25 00 00 00 20 00 00 37 e4 36 8f e0 00 00:00:00.000 READ DMA EXT 25 00 00 00 01 00 00 37 e4 36 af e0 00 00:00:00.000 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 296 --- Lifetime Power-On Resets 0x01 0x010 4 738 --- Power-on Hours 0x01 0x018 6 6280535944 --- Logical Sectors Written 0x01 0x028 6 10199411546 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 44 --- Current Temperature 0x05 0x020 1 55 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 10 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 100 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC