/dev/sda === START OF INFORMATION SECTION === Device Model: ST320LT020-9YG142 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0002HPM1 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Sep 6 12:06:14 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 87) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 118 096 006 - 182453488 3 Spin_Up_Time PO---K 099 099 000 - 0 4 Start_Stop_Count -O--CK 096 096 000 - 4885 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-K 085 060 030 - 13855447627 9 Power_On_Hours -O--CK 076 076 000 - 21349 10 Spin_Retry_Count PO--CK 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4829 183 Runtime_Bad_Block -O--CK 094 094 000 - 6 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 158 188 Command_Timeout -O--CK 100 092 000 - 8590656133 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 064 049 045 - 36 (Min/Max 24/36) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 1291 192 Power-Off_Retract_Count -O---K 100 100 000 - 423 193 Load_Cycle_Count -O--CK 001 001 000 - 285976 194 Temperature_Celsius -O---K 036 051 000 - 36 (0 1 0 0 0) 195 Hardware_ECC_Recovered -O-RCK 052 036 000 - 182453488 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 250 Read_Error_Retry_Rate ------ 100 001 000 - 7622 251 Unknown_Attribute ------ 100 001 000 - 19 252 Unknown_Attribute ------ 100 001 000 - 1 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbd GPL VS 1 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 151 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 151 [10] occurred at disk power-on lifetime: 18929 hours (788 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 18 ad b8 00 00 Error: UNC at LBA = 0x0718adb8 = 119057848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 07 18 ad 3f 40 00 00:02:43.036 READ FPDMA QUEUED 60 00 00 00 02 00 00 07 18 ad f5 40 00 00:02:42.878 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:02:42.877 READ LOG EXT 60 00 00 01 00 00 00 07 18 ad 3f 40 00 00:02:39.175 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 64 f1 3f 40 00 00:02:39.143 READ FPDMA QUEUED Error 150 [9] occurred at disk power-on lifetime: 18929 hours (788 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 18 ad b8 00 00 Error: UNC at LBA = 0x0718adb8 = 119057848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 07 18 ad 3f 40 00 00:02:39.175 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 64 f1 3f 40 00 00:02:39.143 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 64 f0 3f 40 00 00:02:39.115 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 64 ee 3f 40 00 00:02:39.076 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 64 ec 3f 40 00 00:02:39.021 READ FPDMA QUEUED Error 149 [8] occurred at disk power-on lifetime: 18929 hours (788 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 18 ad bf 00 00 Error: UNC at LBA = 0x0718adbf = 119057855 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 07 18 ad bf 40 00 00:00:35.651 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:00:35.650 READ LOG EXT 60 00 00 00 08 00 00 07 18 ad bf 40 00 00:00:31.921 READ FPDMA QUEUED 60 00 00 00 08 00 00 07 16 4c 97 40 00 00:00:31.901 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 5b cc e7 40 00 00:00:31.889 READ FPDMA QUEUED Error 148 [7] occurred at disk power-on lifetime: 18929 hours (788 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 18 ad bf 00 00 Error: UNC at LBA = 0x0718adbf = 119057855 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 07 18 ad bf 40 00 00:00:31.921 READ FPDMA QUEUED 60 00 00 00 08 00 00 07 16 4c 97 40 00 00:00:31.901 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 5b cc e7 40 00 00:00:31.889 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 5b cc df 40 00 00:00:31.878 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 5b cc d7 40 00 00:00:31.862 READ FPDMA QUEUED Error 147 [6] occurred at disk power-on lifetime: 12454 hours (518 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 62 10 70 00 00 Error: WP at LBA = 0x00621070 = 6426736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 10 00 00 0d 6d 7f 0f 40 00 01:16:03.563 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 5e 00 47 40 00 01:16:03.562 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 0d 6d 7e df 40 00 01:16:03.562 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 5e 3e 67 40 00 01:16:03.562 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 0d 6d 7e cf 40 00 01:16:03.561 WRITE FPDMA QUEUED Error 146 [5] occurred at disk power-on lifetime: 12454 hours (518 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 62 10 70 00 00 Error: WP at LBA = 0x00621070 = 6426736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 10 00 00 0d 6d 92 ff 40 00 01:15:59.058 WRITE FPDMA QUEUED 61 00 00 00 18 00 00 0d 6d 92 df 40 00 01:15:59.058 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 0d 6d 92 5f 40 00 01:15:59.057 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 0d 6d 8f 7f 40 00 01:15:59.057 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 0d 6d 8e 17 40 00 01:15:59.056 WRITE FPDMA QUEUED Error 145 [4] occurred at disk power-on lifetime: 12454 hours (518 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 62 10 70 00 00 Error: UNC at LBA = 0x00621070 = 6426736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 00 62 10 3f 40 00 01:15:55.004 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 5e 00 47 40 00 01:15:55.004 WRITE FPDMA QUEUED 60 00 00 00 60 00 00 17 1a 68 3f 40 00 01:15:55.003 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 01:15:54.986 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 01:15:54.950 SET FEATURES [Enable write cache] Error 144 [3] occurred at disk power-on lifetime: 12454 hours (518 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 62 10 70 00 00 Error: UNC at LBA = 0x00621070 = 6426736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 00 62 10 3f 40 00 01:15:50.976 READ FPDMA QUEUED 61 00 00 00 68 00 00 00 e4 1e d7 40 00 01:15:50.976 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 5e 00 47 40 00 01:15:50.975 WRITE FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 01:15:50.975 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 01:15:50.863 SET FEATURES [Enable write cache] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 24/36 Celsius Lifetime Min/Max Temperature: 1/52 Celsius Under/Over Temperature Limit Count: 0/3 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 30 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (26) Index Estimated Time Temperature Celsius 27 2019-09-03 20:30 41 ********************** 28 2019-09-03 21:00 ? - 29 2019-09-03 21:30 43 ************************ 30 2019-09-03 22:00 ? - 31 2019-09-03 22:30 44 ************************* 32 2019-09-03 23:00 ? - 33 2019-09-03 23:30 21 ** 34 2019-09-04 00:00 ? - 35 2019-09-04 00:30 32 ************* 36 2019-09-04 01:00 ? - 37 2019-09-04 01:30 30 *********** 38 2019-09-04 02:00 ? - 39 2019-09-04 02:30 36 ***************** 40 2019-09-04 03:00 ? - 41 2019-09-04 03:30 36 ***************** 42 2019-09-04 04:00 ? - 43 2019-09-04 04:30 35 **************** 44 2019-09-04 05:00 ? - 45 2019-09-04 05:30 32 ************* 46 2019-09-04 06:00 ? - 47 2019-09-04 06:30 31 ************ 48 2019-09-04 07:00 ? - 49 2019-09-04 07:30 33 ************** 50 2019-09-04 08:00 ? - 51 2019-09-04 08:30 34 *************** 52 2019-09-04 09:00 ? - 53 2019-09-04 09:30 28 ********* 54 2019-09-04 10:00 ? - 55 2019-09-04 10:30 30 *********** 56 2019-09-04 11:00 ? - 57 2019-09-04 11:30 29 ********** 58 2019-09-04 12:00 ? - 59 2019-09-04 12:30 30 *********** 60 2019-09-04 13:00 ? - 61 2019-09-04 13:30 26 ******* 62 2019-09-04 14:00 ? - 63 2019-09-04 14:30 27 ******** 64 2019-09-04 15:00 ? - 65 2019-09-04 15:30 37 ****************** 66 2019-09-04 16:00 ? - 67 2019-09-04 16:30 37 ****************** 68 2019-09-04 17:00 ? - 69 2019-09-04 17:30 37 ****************** 70 2019-09-04 18:00 ? - 71 2019-09-04 18:30 37 ****************** 72 2019-09-04 19:00 ? - 73 2019-09-04 19:30 41 ********************** 74 2019-09-04 20:00 ? - 75 2019-09-04 20:30 38 ******************* 76 2019-09-04 21:00 ? - 77 2019-09-04 21:30 38 ******************* 78 2019-09-04 22:00 ? - 79 2019-09-04 22:30 38 ******************* 80 2019-09-04 23:00 ? - 81 2019-09-04 23:30 36 ***************** 82 2019-09-05 00:00 ? - 83 2019-09-05 00:30 31 ************ 84 2019-09-05 01:00 28 ********* 85 2019-09-05 01:30 ? - 86 2019-09-05 02:00 27 ******** 87 2019-09-05 02:30 ? - 88 2019-09-05 03:00 30 *********** 89 2019-09-05 03:30 ? - 90 2019-09-05 04:00 30 *********** 91 2019-09-05 04:30 ? - 92 2019-09-05 05:00 30 *********** 93 2019-09-05 05:30 ? - 94 2019-09-05 06:00 31 ************ 95 2019-09-05 06:30 ? - 96 2019-09-05 07:00 32 ************* 97 2019-09-05 07:30 ? - 98 2019-09-05 08:00 32 ************* 99 2019-09-05 08:30 ? - 100 2019-09-05 09:00 32 ************* 101 2019-09-05 09:30 ? - 102 2019-09-05 10:00 32 ************* 103 2019-09-05 10:30 ? - 104 2019-09-05 11:00 34 *************** 105 2019-09-05 11:30 ? - 106 2019-09-05 12:00 34 *************** 107 2019-09-05 12:30 ? - 108 2019-09-05 13:00 34 *************** 109 2019-09-05 13:30 ? - 110 2019-09-05 14:00 34 *************** 111 2019-09-05 14:30 ? - 112 2019-09-05 15:00 34 *************** 113 2019-09-05 15:30 ? - 114 2019-09-05 16:00 35 **************** 115 2019-09-05 16:30 ? - 116 2019-09-05 17:00 37 ****************** 117 2019-09-05 17:30 ? - 118 2019-09-05 18:00 37 ****************** 119 2019-09-05 18:30 ? - 120 2019-09-05 19:00 23 **** 121 2019-09-05 19:30 35 **************** 122 2019-09-05 20:00 ? - 123 2019-09-05 20:30 37 ****************** 124 2019-09-05 21:00 ? - 125 2019-09-05 21:30 22 *** 126 2019-09-05 22:00 ? - 127 2019-09-05 22:30 27 ******** 0 2019-09-05 23:00 ? - 1 2019-09-05 23:30 29 ********** 2 2019-09-06 00:00 ? - 3 2019-09-06 00:30 30 *********** 4 2019-09-06 01:00 ? - 5 2019-09-06 01:30 36 ***************** 6 2019-09-06 02:00 40 ********************* 7 2019-09-06 02:30 37 ****************** 8 2019-09-06 03:00 41 ********************** 9 2019-09-06 03:30 39 ******************** 10 2019-09-06 04:00 38 ******************* 11 2019-09-06 04:30 ? - 12 2019-09-06 05:00 38 ******************* 13 2019-09-06 05:30 ? - 14 2019-09-06 06:00 21 ** 15 2019-09-06 06:30 34 *************** 16 2019-09-06 07:00 37 ****************** 17 2019-09-06 07:30 ? - 18 2019-09-06 08:00 24 ***** 19 2019-09-06 08:30 ? - 20 2019-09-06 09:00 22 *** 21 2019-09-06 09:30 ? - 22 2019-09-06 10:00 23 **** 23 2019-09-06 10:30 ? - 24 2019-09-06 11:00 24 ***** 25 2019-09-06 11:30 34 *************** 26 2019-09-06 12:00 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS