/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD3200BPVT-22ZEST0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Jan 12 19:36:19 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7380) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 88) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1994 3 Spin_Up_Time POS--K 155 129 021 - 1250 4 Start_Stop_Count -O--CK 079 079 000 - 21643 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10258 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5253 191 G-Sense_Error_Rate -O--CK 001 001 000 - 30272 192 Power-Off_Retract_Count -O--CK 200 200 000 - 656 193 Load_Cycle_Count -O--CK 073 073 000 - 383517 194 Temperature_Celsius -O---K 107 095 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 199 198 000 - 78 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 14034 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 14034 [17] occurred at disk power-on lifetime: 10240 hours (426 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 41 00 20 00 00 0f cf 44 48 40 00 Error: ABRT at LBA = 0x0fcf4448 = 265241672 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 b0 00 00 0f cf 44 48 40 08 00:00:39.206 READ FPDMA QUEUED 60 00 40 00 a8 00 00 03 3e 05 b0 40 08 00:00:39.206 READ FPDMA QUEUED 60 00 88 00 a0 00 00 03 3e 05 f0 40 08 00:00:39.142 READ FPDMA QUEUED 60 00 08 00 98 00 00 08 c1 09 08 40 08 00:00:39.134 READ FPDMA QUEUED 60 00 a8 00 90 00 00 03 32 e7 a8 40 08 00:00:39.123 READ FPDMA QUEUED Error 14033 [16] occurred at disk power-on lifetime: 10230 hours (426 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 41 00 08 00 00 0a 44 2c 78 40 00 Error: ABRT at LBA = 0x0a442c78 = 172239992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 48 00 00 0a 44 2c 78 40 08 00:34:06.774 READ FPDMA QUEUED 60 00 10 00 40 00 00 21 84 46 c0 40 08 00:34:06.772 READ FPDMA QUEUED 60 00 08 00 38 00 00 08 c4 cd 38 40 08 00:34:06.758 READ FPDMA QUEUED 60 00 08 00 30 00 00 07 84 63 e8 40 08 00:34:06.735 READ FPDMA QUEUED 60 00 10 00 28 00 00 21 84 46 38 40 08 00:34:06.701 READ FPDMA QUEUED Error 14032 [15] occurred at disk power-on lifetime: 10228 hours (426 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 04 79 39 40 00 Error: UNC at LBA = 0x02047939 = 33847609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 68 00 10 00 00 00 03 5e d8 40 00 00:00:46.288 READ FPDMA QUEUED 60 00 08 00 08 00 00 02 04 79 38 40 00 00:00:46.288 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:46.287 SET FEATURES [Enable write cache] 60 00 68 00 10 00 00 00 03 5e d8 40 00 00:00:46.020 READ FPDMA QUEUED 60 00 08 00 08 00 00 02 04 79 38 40 00 00:00:46.020 READ FPDMA QUEUED Error 14031 [14] occurred at disk power-on lifetime: 10228 hours (426 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 04 79 39 40 00 Error: UNC at LBA = 0x02047939 = 33847609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 68 00 10 00 00 00 03 5e d8 40 00 00:00:46.020 READ FPDMA QUEUED 60 00 08 00 08 00 00 02 04 79 38 40 00 00:00:46.020 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:46.020 SET FEATURES [Enable write cache] 60 00 68 00 10 00 00 00 03 5e d8 40 00 00:00:45.742 READ FPDMA QUEUED 60 00 08 00 08 00 00 02 04 79 38 40 00 00:00:45.742 READ FPDMA QUEUED Error 14030 [13] occurred at disk power-on lifetime: 10228 hours (426 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 04 79 39 40 00 Error: UNC at LBA = 0x02047939 = 33847609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 68 00 10 00 00 00 03 5e d8 40 00 00:00:45.742 READ FPDMA QUEUED 60 00 08 00 08 00 00 02 04 79 38 40 00 00:00:45.742 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:45.742 SET FEATURES [Enable write cache] 60 00 68 00 08 00 00 00 03 5e d8 40 00 00:00:45.507 READ FPDMA QUEUED 60 00 08 00 10 00 00 02 04 79 38 40 00 00:00:45.479 READ FPDMA QUEUED Error 14029 [12] occurred at disk power-on lifetime: 10228 hours (426 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 04 79 39 40 00 Error: UNC at LBA = 0x02047939 = 33847609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 68 00 08 00 00 00 03 5e d8 40 00 00:00:45.507 READ FPDMA QUEUED 60 00 08 00 10 00 00 02 04 79 38 40 00 00:00:45.479 READ FPDMA QUEUED 60 00 80 00 08 00 00 00 03 5e 58 40 00 00:00:45.479 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:45.479 SET FEATURES [Enable write cache] 60 00 08 00 10 00 00 02 04 79 38 40 00 00:00:45.212 READ FPDMA QUEUED Error 14028 [11] occurred at disk power-on lifetime: 10228 hours (426 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 04 79 39 40 00 Error: UNC at LBA = 0x02047939 = 33847609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 02 04 79 38 40 00 00:00:45.212 READ FPDMA QUEUED 60 00 80 00 08 00 00 00 03 5e 58 40 00 00:00:45.212 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:45.212 SET FEATURES [Enable write cache] 60 00 08 00 10 00 00 02 04 79 38 40 00 00:00:44.944 READ FPDMA QUEUED 60 00 80 00 08 00 00 00 03 5e 58 40 00 00:00:44.944 READ FPDMA QUEUED Error 14027 [10] occurred at disk power-on lifetime: 10228 hours (426 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 04 79 39 40 00 Error: UNC at LBA = 0x02047939 = 33847609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 10 00 00 02 04 79 38 40 00 00:00:44.944 READ FPDMA QUEUED 60 00 80 00 08 00 00 00 03 5e 58 40 00 00:00:44.944 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:44.944 SET FEATURES [Enable write cache] 60 00 08 00 10 00 00 02 04 79 38 40 00 00:00:44.667 READ FPDMA QUEUED 60 00 80 00 08 00 00 00 03 5e 58 40 00 00:00:44.667 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 25/36 Celsius Lifetime Min/Max Temperature: 21/49 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2019-01-12 17:29 39 ******************** ... ..( 2 skipped). .. ******************** 50 2019-01-12 17:32 39 ******************** 51 2019-01-12 17:33 38 ******************* 52 2019-01-12 17:34 ? - 53 2019-01-12 17:35 39 ******************** 54 2019-01-12 17:36 38 ******************* 55 2019-01-12 17:37 39 ******************** 56 2019-01-12 17:38 ? - 57 2019-01-12 17:39 38 ******************* 58 2019-01-12 17:40 39 ******************** 59 2019-01-12 17:41 ? - 60 2019-01-12 17:42 39 ******************** ... ..( 10 skipped). .. ******************** 71 2019-01-12 17:53 39 ******************** 72 2019-01-12 17:54 40 ********************* 73 2019-01-12 17:55 40 ********************* 74 2019-01-12 17:56 39 ******************** ... ..( 3 skipped). .. ******************** 78 2019-01-12 18:00 39 ******************** 79 2019-01-12 18:01 ? - 80 2019-01-12 18:02 40 ********************* ... ..( 6 skipped). .. ********************* 87 2019-01-12 18:09 40 ********************* 88 2019-01-12 18:10 ? - 89 2019-01-12 18:11 24 ***** ... ..( 2 skipped). .. ***** 92 2019-01-12 18:14 24 ***** 93 2019-01-12 18:15 23 **** 94 2019-01-12 18:16 ? - 95 2019-01-12 18:17 24 ***** 96 2019-01-12 18:18 ? - 97 2019-01-12 18:19 24 ***** 98 2019-01-12 18:20 23 **** 99 2019-01-12 18:21 ? - 100 2019-01-12 18:22 23 **** 101 2019-01-12 18:23 23 **** 102 2019-01-12 18:24 23 **** 103 2019-01-12 18:25 ? - 104 2019-01-12 18:26 22 *** 105 2019-01-12 18:27 23 **** 106 2019-01-12 18:28 ? - 107 2019-01-12 18:29 23 **** 108 2019-01-12 18:30 ? - 109 2019-01-12 18:31 22 *** 110 2019-01-12 18:32 22 *** 111 2019-01-12 18:33 ? - 112 2019-01-12 18:34 23 **** 113 2019-01-12 18:35 ? - 114 2019-01-12 18:36 22 *** 115 2019-01-12 18:37 22 *** 116 2019-01-12 18:38 21 ** 117 2019-01-12 18:39 22 *** 118 2019-01-12 18:40 22 *** 119 2019-01-12 18:41 ? - 120 2019-01-12 18:42 22 *** 121 2019-01-12 18:43 ? - 122 2019-01-12 18:44 21 ** ... ..( 3 skipped). .. ** 126 2019-01-12 18:48 21 ** 127 2019-01-12 18:49 ? - 0 2019-01-12 18:50 25 ****** 1 2019-01-12 18:51 26 ******* 2 2019-01-12 18:52 27 ******** 3 2019-01-12 18:53 28 ********* 4 2019-01-12 18:54 27 ******** 5 2019-01-12 18:55 ? - 6 2019-01-12 18:56 28 ********* 7 2019-01-12 18:57 28 ********* 8 2019-01-12 18:58 ? - 9 2019-01-12 18:59 28 ********* 10 2019-01-12 19:00 28 ********* 11 2019-01-12 19:01 ? - 12 2019-01-12 19:02 28 ********* 13 2019-01-12 19:03 28 ********* 14 2019-01-12 19:04 ? - 15 2019-01-12 19:05 28 ********* 16 2019-01-12 19:06 28 ********* 17 2019-01-12 19:07 ? - 18 2019-01-12 19:08 29 ********** 19 2019-01-12 19:09 30 *********** 20 2019-01-12 19:10 30 *********** 21 2019-01-12 19:11 30 *********** 22 2019-01-12 19:12 31 ************ ... ..( 2 skipped). .. ************ 25 2019-01-12 19:15 31 ************ 26 2019-01-12 19:16 32 ************* 27 2019-01-12 19:17 32 ************* 28 2019-01-12 19:18 33 ************** 29 2019-01-12 19:19 33 ************** 30 2019-01-12 19:20 33 ************** 31 2019-01-12 19:21 34 *************** ... ..( 2 skipped). .. *************** 34 2019-01-12 19:24 34 *************** 35 2019-01-12 19:25 35 **************** ... ..( 5 skipped). .. **************** 41 2019-01-12 19:31 35 **************** 42 2019-01-12 19:32 36 ***************** ... ..( 3 skipped). .. ***************** 46 2019-01-12 19:36 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 2234 Vendor specific