/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD7500BPVT-60HXZT3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Feb 22 18:49:00 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: (16500) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 162) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 178 176 021 - 2091 4 Start_Stop_Count -O--CK 088 088 000 - 12488 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 073 073 000 - 20341 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 088 088 000 - 12117 183 Runtime_Bad_Block -O--CK 096 096 000 - 4 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 095 000 - 7 188 Command_Timeout -O--CK 100 092 000 - 34360328202 190 Airflow_Temperature_Cel -O---K 060 048 040 - 40 (Min/Max 40/40) 191 G-Sense_Error_Rate -O--CK 001 001 000 - 1455 192 Power-Off_Retract_Count -O--CK 200 200 000 - 196 193 Load_Cycle_Count -O--CK 001 001 000 - 3500442 194 Temperature_Celsius -O---K 107 095 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 11 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 11 [10] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:17:58.236 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:58.236 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:17:58.232 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:17:58.231 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:58.231 SET FEATURES [Enable SATA feature] Error 10 [9] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 0d 30 ad e0 a0 00 Error: IDNF at LBA = 0x0d30ade0 = 221294048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 08 f0 00 60 00 00 0d 30 ad e0 40 08 00:17:49.710 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:49.708 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:17:49.704 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:17:49.704 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:49.704 SET FEATURES [Enable SATA feature] Error 9 [8] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:17:41.177 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:41.176 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:17:41.171 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:17:41.170 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:41.170 SET FEATURES [Enable SATA feature] Error 8 [7] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 0d 31 ac 20 a0 00 Error: IDNF at LBA = 0x0d31ac20 = 221359136 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 05 a0 00 d0 00 00 0d 31 ac 20 40 08 00:17:32.646 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:32.646 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:17:32.642 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:17:32.641 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:32.641 SET FEATURES [Enable SATA feature] Error 7 [6] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:17:24.123 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:24.123 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:17:24.119 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:17:24.119 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:24.119 SET FEATURES [Enable SATA feature] Error 6 [5] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 01 41 68 30 a0 00 Error: IDNF at LBA = 0x01416830 = 21063728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 78 00 00 01 41 68 30 40 08 00:17:15.595 WRITE FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:15.595 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:17:15.591 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:17:15.591 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:15.591 SET FEATURES [Enable SATA feature] Error 5 [4] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:17:07.061 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:07.060 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:17:07.056 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:17:07.056 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:17:07.056 SET FEATURES [Enable SATA feature] Error 4 [3] occurred at disk power-on lifetime: 20087 hours (836 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 0d 31 ac 20 40 00 Error: IDNF at LBA = 0x0d31ac20 = 221359136 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 50 00 00 01 41 68 30 40 08 00:16:56.773 WRITE FPDMA QUEUED 61 01 30 00 48 00 00 00 5a 1f d0 40 08 00:16:56.773 WRITE FPDMA QUEUED 61 00 20 00 40 00 00 0d 02 0d 80 40 08 00:16:56.773 WRITE FPDMA QUEUED 61 00 20 00 38 00 00 0d 02 0b 60 40 08 00:16:56.773 WRITE FPDMA QUEUED 61 03 40 00 30 00 00 0d 30 b6 d0 40 08 00:16:56.763 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 8190 - # 2 Extended offline Aborted by host 90% 2231 - # 3 Extended offline Aborted by host 90% 1822 - # 4 Short offline Aborted by host 10% 1254 - # 5 Extended offline Aborted by host 90% 1253 - # 6 Short offline Completed without error 00% 1029 - # 7 Short offline Aborted by host 90% 1015 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 40/40 Celsius Lifetime Min/Max Temperature: 0/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (0) Index Estimated Time Temperature Celsius 1 2022-02-22 16:42 38 ******************* ... ..( 17 skipped). .. ******************* 19 2022-02-22 17:00 38 ******************* 20 2022-02-22 17:01 39 ******************** ... ..( 53 skipped). .. ******************** 74 2022-02-22 17:55 39 ******************** 75 2022-02-22 17:56 40 ********************* ... ..( 43 skipped). .. ********************* 119 2022-02-22 18:40 40 ********************* 120 2022-02-22 18:41 41 ********************** 121 2022-02-22 18:42 41 ********************** 122 2022-02-22 18:43 41 ********************** 123 2022-02-22 18:44 40 ********************* 124 2022-02-22 18:45 40 ********************* 125 2022-02-22 18:46 ? - 126 2022-02-22 18:47 40 ********************* 127 2022-02-22 18:48 40 ********************* 0 2022-02-22 18:49 40 ********************* SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 177 Vendor specific