/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven OEM SSDs Device Model: GOODRAM Serial Number: -- Firmware Version: SAFM12.2 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 14 15:54:30 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 13597 9 Power_On_Hours -O--C- 100 100 000 - 1056 12 Power_Cycle_Count -O--C- 100 100 000 - 861 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 177 170 Bad_Blk_Ct_Erl/Lat PO---- 086 086 010 - 10/97 173 MaxAvgErase_Ct -O--C- 100 100 000 - 78 (Average 51) 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 263 194 Temperature_Celsius PO---K 098 098 057 - 30 (Min/Max 30/30) 218 CRC_Error_Count PO-R-- 100 100 050 - 135 231 SSD_Life_Left PO--C- 100 100 000 - 95 241 Lifetime_Writes_GiB -O--C- 100 100 000 - 7529 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 13597 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13597 [28] occurred at disk power-on lifetime: 1050 hours (43 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 00 00 03 8a 1b 40 00 Error: UNC at LBA = 0x00038a1b = 231963 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 00 00 00 00 03 8a 1b 40 00 00:00:00.818 READ FPDMA QUEUED 60 00 10 00 00 00 00 00 03 8a 1b 40 00 00:00:00.817 READ FPDMA QUEUED 60 00 01 00 00 00 00 00 00 00 3f 40 00 00:00:00.813 READ FPDMA QUEUED 60 00 20 00 00 00 00 00 00 00 3f 40 00 00:00:00.812 READ FPDMA QUEUED 60 00 10 00 00 00 00 00 00 00 3f 40 00 00:00:00.810 READ FPDMA QUEUED Error 13596 [27] occurred at disk power-on lifetime: 842 hours (35 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 b8 00 00 08 59 5a 10 40 00 Error: UNC at LBA = 0x08595a10 = 140073488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b8 00 00 08 59 5a 10 40 00 01:10:58.208 READ FPDMA QUEUED 60 00 18 00 b0 00 00 06 bd 3c 20 40 00 01:10:58.208 READ FPDMA QUEUED 60 00 18 00 a8 00 00 06 bd 3c 20 40 00 01:10:57.708 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.706 READ LOG EXT 60 00 18 00 a8 00 00 06 bd 3c 20 40 00 01:10:57.705 READ FPDMA QUEUED Error 13595 [26] occurred at disk power-on lifetime: 842 hours (35 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 a8 00 00 06 bd 3c 20 40 00 Error: UNC at LBA = 0x06bd3c20 = 113064992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 a8 00 00 06 bd 3c 20 40 00 01:10:57.705 READ FPDMA QUEUED 60 00 18 00 a0 00 00 06 bd 3c 20 40 00 01:10:57.705 READ FPDMA QUEUED 60 00 08 00 98 00 00 08 59 5a 10 40 00 01:10:57.705 READ FPDMA QUEUED 60 00 10 00 90 00 00 06 bd 3a 70 40 00 01:10:57.705 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.702 READ LOG EXT Error 13594 [25] occurred at disk power-on lifetime: 842 hours (35 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 88 00 00 08 59 5a 10 40 00 Error: UNC at LBA = 0x08595a10 = 140073488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 08 59 5a 10 40 00 01:10:57.702 READ FPDMA QUEUED 60 00 10 00 80 00 00 06 bd 3a a0 40 00 01:10:57.702 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.699 READ LOG EXT 60 00 40 00 78 00 00 08 59 5a 10 40 00 01:10:57.699 READ FPDMA QUEUED 60 00 38 00 70 00 00 06 bd 49 18 40 00 01:10:57.697 READ FPDMA QUEUED Error 13593 [24] occurred at disk power-on lifetime: 842 hours (35 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 78 00 00 08 59 5a 10 40 00 Error: UNC at LBA = 0x08595a10 = 140073488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 78 00 00 08 59 5a 10 40 00 01:10:57.699 READ FPDMA QUEUED 60 00 38 00 70 00 00 06 bd 49 18 40 00 01:10:57.697 READ FPDMA QUEUED 60 00 20 00 68 00 00 06 bd 56 78 40 00 01:10:57.696 READ FPDMA QUEUED 60 00 10 00 60 00 00 06 bd 56 88 40 00 01:10:57.696 READ FPDMA QUEUED 60 00 18 00 58 00 00 06 bd 56 88 40 00 01:10:57.696 READ FPDMA QUEUED Error 13592 [23] occurred at disk power-on lifetime: 842 hours (35 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 38 00 00 08 59 5a 10 40 00 Error: UNC at LBA = 0x08595a10 = 140073488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 08 59 5a 10 40 00 01:10:57.635 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.633 READ LOG EXT 60 00 08 00 30 00 00 08 59 5a 10 40 00 01:10:57.632 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.629 READ LOG EXT 60 00 08 00 28 00 00 08 59 5a 10 40 00 01:10:57.629 READ FPDMA QUEUED Error 13591 [22] occurred at disk power-on lifetime: 842 hours (35 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 30 00 00 08 59 5a 10 40 00 Error: UNC at LBA = 0x08595a10 = 140073488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 30 00 00 08 59 5a 10 40 00 01:10:57.632 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.629 READ LOG EXT 60 00 08 00 28 00 00 08 59 5a 10 40 00 01:10:57.629 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.626 READ LOG EXT 60 00 08 00 20 00 00 08 59 5a 10 40 00 01:10:57.625 READ FPDMA QUEUED Error 13590 [21] occurred at disk power-on lifetime: 842 hours (35 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 00 08 59 5a 10 40 00 Error: UNC at LBA = 0x08595a10 = 140073488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 08 59 5a 10 40 00 01:10:57.629 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.626 READ LOG EXT 60 00 08 00 20 00 00 08 59 5a 10 40 00 01:10:57.625 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 01:10:57.623 READ LOG EXT 60 00 08 00 18 00 00 08 59 5a 10 40 00 01:10:57.622 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 915 - # 2 Short offline Completed without error 00% 869 - # 3 Short offline Completed without error 00% 726 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 861 --- Lifetime Power-On Resets 0x01 0x010 4 1056 --- Power-on Hours 0x01 0x018 6 15789905962 --- Logical Sectors Written 0x01 0x020 6 244081771 --- Number of Write Commands 0x01 0x028 6 15358779356 --- Logical Sectors Read 0x01 0x030 6 198576507 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 5360 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 86 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x010 1 32 --- Average Short Term Temperature 0x05 0x018 1 32 --- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 5 --- Lowest Temperature 0x05 0x030 1 50 --- Highest Average Short Term Temperature 0x05 0x038 1 16 --- Lowest Average Short Term Temperature 0x05 0x040 1 50 --- Highest Average Long Term Temperature 0x05 0x048 1 16 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 50 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 5866 --- Number of Hardware Resets 0x06 0x018 4 133 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 7 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC