Probe #9e6843fe2e of Dell Inspiron 5420

Log: smartctl

/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.2-arch1-1] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue / Red / Green SSDs Device Model: WDC WDS120G2G0A-00JH30 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UE510000 User Capacity: 120,040,980,480 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Mar 10 14:56:35 2023 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 3555 12 Power_Cycle_Count -O--CK 100 100 000 - 1942 165 Block_Erase_Count -O--CK 100 100 000 - 3271 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 43 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 0 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 56 169 Total_Bad_Blocks -O--CK 100 100 --- - 347 170 Grown_Bad_Blocks -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 43 174 Unexpected_Power_Loss -O--CK 100 100 000 - 972 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 058 053 000 - 42 (Min/Max 16/53) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x0922083c0922 232 Available_Reservd_Space PO--CK 100 100 005 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 5141 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 18202 241 Host_Writes_GiB ----CK 100 100 000 - 6655 242 Host_Reads_GiB ----CK 100 100 000 - 7346 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 2728 - # 2 Short offline Aborted by host 90% 2701 - # 3 Short offline Aborted by host 90% 2564 - # 4 Short offline Aborted by host 90% 2565 - # 5 Short offline Aborted by host 90% 2565 - # 6 Short offline Interrupted (host reset) 90% 2564 - # 7 Short offline Aborted by host 90% 2565 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1942 --- Lifetime Power-On Resets 0x01 0x010 4 3555 --- Power-on Hours 0x01 0x018 6 13957007705 --- Logical Sectors Written 0x01 0x028 6 15407332961 --- Logical Sectors Read 0x01 0x038 6 3555 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 42 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 44 --- Highest Average Short Term Temperature 0x05 0x038 1 44 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 8 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 11436 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.2-arch1-1] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST1000LM024 HN-M101MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR20003 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Mar 10 14:56:35 2023 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 36) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: (12720) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 212) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1587 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 089 089 025 - 3454 4 Start_Stop_Count -O--CK 092 092 000 - 8428 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 8185 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 99 12 Power_Cycle_Count -O--CK 094 094 000 - 7058 13 Read_Soft_Error_Rate -O-RCK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 099 099 000 - 33089479 191 G-Sense_Error_Rate -O---K 100 100 000 - 4228 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 088 088 000 - 121349 194 Temperature_Celsius -O---- 064 050 000 - 33 (Min/Max 18/51) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 1 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 1528 240 Head_Flying_Hours -O--CK 100 100 000 - 7588 241 Total_LBAs_Written -O--CK 098 094 000 - 4049666 242 Total_LBAs_Read -O--CK 095 094 000 - 7779972 254 Free_Fall_Sensor -O--CK 252 252 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 690 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 690 [1] occurred at disk power-on lifetime: 8014 hours (333 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 f0 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 da 04 00 00 00 00 00 18 e8 40 08 00:00:04.627 READ FPDMA QUEUED 60 00 00 01 20 00 00 00 00 1c e8 40 08 00:00:04.631 READ FPDMA QUEUED 60 00 d5 04 00 00 00 00 00 18 e8 40 08 00:00:04.631 READ FPDMA QUEUED 60 00 00 01 18 00 00 00 00 17 c8 40 08 00:00:04.631 READ FPDMA QUEUED 60 00 00 04 00 00 00 00 00 13 c8 40 08 00:00:04.631 READ FPDMA QUEUED Error 689 [0] occurred at disk power-on lifetime: 8014 hours (333 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 03 10 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 74 70 6d 00 40 08 00:00:03.832 READ FPDMA QUEUED 60 00 05 05 20 00 00 00 00 18 e8 40 08 00:00:03.826 READ FPDMA QUEUED 60 00 00 05 20 00 00 00 00 18 e8 40 08 00:00:03.830 READ FPDMA QUEUED 60 00 00 01 18 00 00 00 00 17 c8 40 08 00:00:03.830 READ FPDMA QUEUED ec 00 00 00 01 00 00 00 00 00 00 00 08 00:00:03.830 IDENTIFY DEVICE Error 688 [7] occurred at disk power-on lifetime: 8014 hours (333 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 03 00 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 20 00 00 00 00 19 d8 40 08 00:00:03.760 READ FPDMA QUEUED 60 00 00 04 50 00 00 00 00 1d f8 40 08 00:00:03.762 READ FPDMA QUEUED 60 00 00 04 20 00 00 00 00 19 d8 40 08 00:00:03.762 READ FPDMA QUEUED 60 00 00 05 40 00 00 00 00 14 98 40 08 00:00:03.762 READ FPDMA QUEUED ec 00 00 00 01 00 00 00 00 00 00 00 08 00:00:03.762 IDENTIFY DEVICE Error 687 [6] occurred at disk power-on lifetime: 8010 hours (333 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 03 00 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 d5 04 50 00 00 00 00 1d f8 40 08 00:00:10.381 READ FPDMA QUEUED 60 00 00 09 60 00 00 00 00 14 98 40 08 00:00:10.294 READ FPDMA QUEUED 60 00 d5 09 60 00 00 00 00 14 98 40 08 00:00:10.379 READ FPDMA QUEUED 60 00 d5 05 10 00 00 00 00 0f 88 40 08 00:00:10.379 READ FPDMA QUEUED 60 00 00 02 98 00 00 00 00 0c f0 40 08 00:00:10.379 READ FPDMA QUEUED Error 686 [5] occurred at disk power-on lifetime: 8009 hours (333 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 03 00 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 90 04 20 00 00 00 00 19 d8 40 00 00:00:06.104 READ FPDMA QUEUED 60 00 d5 04 50 00 00 00 00 1d f8 40 08 00:00:06.120 READ FPDMA QUEUED 60 00 90 04 20 00 00 00 00 19 d8 40 00 00:00:06.120 READ FPDMA QUEUED 60 00 d5 05 40 00 00 00 00 14 98 40 08 00:00:06.120 READ FPDMA QUEUED 60 00 d5 05 10 00 00 00 00 0f 88 40 08 00:00:06.120 READ FPDMA QUEUED Error 685 [4] occurred at disk power-on lifetime: 8009 hours (333 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 03 00 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 d5 04 50 00 00 00 00 1d f8 40 08 00:00:06.075 READ FPDMA QUEUED 60 00 90 09 60 00 00 00 00 14 98 40 00 00:00:06.070 READ FPDMA QUEUED 60 00 d5 09 60 00 00 00 00 14 98 40 08 00:00:06.073 READ FPDMA QUEUED 60 00 d5 05 10 00 00 00 00 0f 88 40 08 00:00:06.073 READ FPDMA QUEUED 60 00 90 02 c0 00 00 00 00 0c c8 40 00 00:00:06.073 READ FPDMA QUEUED Error 684 [3] occurred at disk power-on lifetime: 8009 hours (333 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 03 00 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 d5 04 50 00 00 00 00 1d f8 40 08 00:00:06.028 READ FPDMA QUEUED 60 00 90 09 60 00 00 00 00 14 98 40 00 00:00:05.737 READ FPDMA QUEUED 60 00 d5 09 60 00 00 00 00 14 98 40 08 00:00:06.027 READ FPDMA QUEUED 60 00 d5 05 10 00 00 00 00 0f 88 40 08 00:00:06.027 READ FPDMA QUEUED 60 00 d5 08 00 00 00 00 00 07 88 40 08 00:00:06.027 READ FPDMA QUEUED Error 683 [2] occurred at disk power-on lifetime: 8009 hours (333 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 03 00 00 00 00 00 1a f8 40 00 Error: UNC at LBA = 0x00001af8 = 6904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 d5 04 50 00 00 00 00 1d f8 40 08 00:00:05.692 READ FPDMA QUEUED 60 00 00 09 60 00 00 00 00 14 98 40 08 00:00:05.614 READ FPDMA QUEUED 60 00 d5 09 60 00 00 00 00 14 98 40 08 00:00:05.690 READ FPDMA QUEUED 60 00 d5 05 10 00 00 00 00 0f 88 40 08 00:00:05.690 READ FPDMA QUEUED 60 00 d5 08 00 00 00 00 00 07 88 40 08 00:00:05.690 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 40% 7381 - # 2 Short offline Interrupted (host reset) 90% 6849 - # 3 Short offline Completed without error 00% 6768 - # 4 Short offline Completed: read failure 90% 1779 37288576 # 5 Short offline Completed: read failure 90% 1749 37288576 # 6 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Interrupted [40% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 33/34 Celsius Lifetime Min/Max Temperature: 18/49 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (27) Index Estimated Time Temperature Celsius 28 2023-03-10 04:20 33 ************** 29 2023-03-10 04:25 34 *************** 30 2023-03-10 04:30 35 **************** ... ..( 2 skipped). .. **************** 33 2023-03-10 04:45 35 **************** 34 2023-03-10 04:50 34 *************** 35 2023-03-10 04:55 34 *************** 36 2023-03-10 05:00 35 **************** 37 2023-03-10 05:05 35 **************** 38 2023-03-10 05:10 34 *************** 39 2023-03-10 05:15 34 *************** 40 2023-03-10 05:20 33 ************** 41 2023-03-10 05:25 33 ************** 42 2023-03-10 05:30 34 *************** ... ..( 2 skipped). .. *************** 45 2023-03-10 05:45 34 *************** 46 2023-03-10 05:50 33 ************** 47 2023-03-10 05:55 33 ************** 48 2023-03-10 06:00 33 ************** 49 2023-03-10 06:05 34 *************** ... ..( 4 skipped). .. *************** 54 2023-03-10 06:30 34 *************** 55 2023-03-10 06:35 35 **************** ... ..( 2 skipped). .. **************** 58 2023-03-10 06:50 35 **************** 59 2023-03-10 06:55 34 *************** 60 2023-03-10 07:00 35 **************** 61 2023-03-10 07:05 36 ***************** 62 2023-03-10 07:10 36 ***************** 63 2023-03-10 07:15 36 ***************** 64 2023-03-10 07:20 38 ******************* 65 2023-03-10 07:25 35 **************** 66 2023-03-10 07:30 35 **************** 67 2023-03-10 07:35 35 **************** 68 2023-03-10 07:40 36 ***************** 69 2023-03-10 07:45 36 ***************** 70 2023-03-10 07:50 34 *************** 71 2023-03-10 07:55 35 **************** 72 2023-03-10 08:00 35 **************** 73 2023-03-10 08:05 34 *************** 74 2023-03-10 08:10 34 *************** 75 2023-03-10 08:15 35 **************** ... ..( 6 skipped). .. **************** 82 2023-03-10 08:50 35 **************** 83 2023-03-10 08:55 34 *************** 84 2023-03-10 09:00 33 ************** 85 2023-03-10 09:05 33 ************** 86 2023-03-10 09:10 30 *********** 87 2023-03-10 09:15 32 ************* 88 2023-03-10 09:20 34 *************** 89 2023-03-10 09:25 34 *************** 90 2023-03-10 09:30 35 **************** 91 2023-03-10 09:35 34 *************** 92 2023-03-10 09:40 34 *************** 93 2023-03-10 09:45 34 *************** 94 2023-03-10 09:50 35 **************** 95 2023-03-10 09:55 35 **************** 96 2023-03-10 10:00 35 **************** 97 2023-03-10 10:05 34 *************** 98 2023-03-10 10:10 34 *************** 99 2023-03-10 10:15 33 ************** 100 2023-03-10 10:20 33 ************** 101 2023-03-10 10:25 34 *************** 102 2023-03-10 10:30 34 *************** 103 2023-03-10 10:35 31 ************ 104 2023-03-10 10:40 34 *************** 105 2023-03-10 10:45 33 ************** 106 2023-03-10 10:50 33 ************** 107 2023-03-10 10:55 35 **************** 108 2023-03-10 11:00 37 ****************** 109 2023-03-10 11:05 38 ******************* 110 2023-03-10 11:10 39 ******************** 111 2023-03-10 11:15 36 ***************** 112 2023-03-10 11:20 35 **************** 113 2023-03-10 11:25 34 *************** ... ..( 3 skipped). .. *************** 117 2023-03-10 11:45 34 *************** 118 2023-03-10 11:50 35 **************** 119 2023-03-10 11:55 36 ***************** 120 2023-03-10 12:00 37 ****************** 121 2023-03-10 12:05 36 ***************** 122 2023-03-10 12:10 35 **************** 123 2023-03-10 12:15 35 **************** 124 2023-03-10 12:20 35 **************** 125 2023-03-10 12:25 36 ***************** ... ..( 2 skipped). .. ***************** 0 2023-03-10 12:40 36 ***************** 1 2023-03-10 12:45 35 **************** ... ..( 2 skipped). .. **************** 4 2023-03-10 13:00 35 **************** 5 2023-03-10 13:05 34 *************** 6 2023-03-10 13:10 33 ************** 7 2023-03-10 13:15 34 *************** ... ..( 2 skipped). .. *************** 10 2023-03-10 13:30 34 *************** 11 2023-03-10 13:35 33 ************** 12 2023-03-10 13:40 33 ************** 13 2023-03-10 13:45 33 ************** 14 2023-03-10 13:50 30 *********** 15 2023-03-10 13:55 32 ************* 16 2023-03-10 14:00 33 ************** 17 2023-03-10 14:05 34 *************** ... ..( 3 skipped). .. *************** 21 2023-03-10 14:25 34 *************** 22 2023-03-10 14:30 33 ************** 23 2023-03-10 14:35 34 *************** ... ..( 3 skipped). .. *************** 27 2023-03-10 14:55 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific


Hardware for Linux and BSD

GitHub