/dev/nvme0n1 smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.6-300.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: CT1000P2SSD8 Serial Number: -- Firmware Version: P2CR033 PCI Vendor/Subsystem ID: 0xc0a9 IEEE OUI Identifier: 0x6479a7 Total NVM Capacity: 1,000,204,886,016 [1.00 TB] Unallocated NVM Capacity: 0 Controller ID: 1 NVMe Version: 1.3 Number of Namespaces: 1 Namespace 1 Size/Capacity: 1,000,204,886,016 [1.00 TB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 6479a7 ... Local Time is: Sun May 25 17:34:45 2025 -04 Firmware Updates (0x12): 1 Slot, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005e): Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x0e): Cmd_Eff_Lg Ext_Get_Lg Telmtry_Lg Maximum Data Transfer Size: 64 Pages Warning Comp. Temp. Threshold: 70 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 3.50W - - 0 0 0 0 0 0 1 + 1.90W - - 1 1 1 1 0 0 2 + 1.50W - - 2 2 2 2 0 0 3 - 0.0700W - - 3 3 3 3 5000 1900 4 - 0.0020W - - 4 4 4 4 13000 100000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 1 1 - 4096 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02, NSID 0xffffffff) Critical Warning: 0x00 Temperature: 34 Celsius Available Spare: 100% Available Spare Threshold: 5% Percentage Used: 4% Data Units Read: 60,643,550 [31.0 TB] Data Units Written: 36,689,025 [18.7 TB] Host Read Commands: 699,083,272 Host Write Commands: 555,833,405 Controller Busy Time: 17,880 Power Cycles: 1,430 Power On Hours: 8,486 Unsafe Shutdowns: 96 Media and Data Integrity Errors: 0 Error Information Log Entries: 2,708 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Error Information (NVMe Log 0x01, 16 of 16 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS Message 0 2708 0 0x0004 0x4005 0x028 0 0 - Invalid Field in Command Self-test Log (NVMe Log 0x06, NSID 0xffffffff) Self-test status: No self-test in progress No Self-tests Logged /dev/nvme1n1 smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.6-300.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: CT2000P3PSSD8 Serial Number: -- Firmware Version: P9CR40D PCI Vendor/Subsystem ID: 0xc0a9 IEEE OUI Identifier: 0x00a075 Controller ID: 1 NVMe Version: 1.4 Number of Namespaces: 1 Namespace 1 Size/Capacity: 2,000,398,934,016 [2.00 TB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 6479a7 ... Local Time is: Sun May 25 17:34:45 2025 -04 Firmware Updates (0x12): 1 Slot, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005e): Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Log Page Attributes (0x06): Cmd_Eff_Lg Ext_Get_Lg Maximum Data Transfer Size: 64 Pages Warning Comp. Temp. Threshold: 85 Celsius Critical Comp. Temp. Threshold: 95 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 6.00W 0.0000W - 0 0 0 0 0 0 1 + 3.00W 0.0000W - 1 1 1 1 0 0 2 + 1.50W 0.0000W - 2 2 2 2 0 0 3 - 0.0250W 0.0000W - 3 3 3 3 5000 1900 4 - 0.0030W - - 4 4 4 4 13000 100000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 1 1 - 4096 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02, NSID 0xffffffff) Critical Warning: 0x00 Temperature: 26 Celsius Available Spare: 100% Available Spare Threshold: 5% Percentage Used: 1% Data Units Read: 12,928,508 [6.61 TB] Data Units Written: 10,151,905 [5.19 TB] Host Read Commands: 82,356,254 Host Write Commands: 27,158,346 Controller Busy Time: 266 Power Cycles: 422 Power On Hours: 1,999 Unsafe Shutdowns: 35 Media and Data Integrity Errors: 0 Error Information Log Entries: 2,176 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 26 Celsius Temperature Sensor 2: 40 Celsius Temperature Sensor 8: 26 Celsius Error Information (NVMe Log 0x01, 16 of 16 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS Message 0 2176 0 0x0018 0x4005 0x028 0 0 - Invalid Field in Command Self-test Log (NVMe Log 0x06, NSID 0xffffffff) Self-test status: No self-test in progress No Self-tests Logged /dev/sda smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.6-300.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: GIGABYTE GP-GSTFS31480GNTD Serial Number: -- Firmware Version: SBFM61.5 User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.5/5706 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 25 17:34:45 2025 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 137 12 Power_Cycle_Count -O--C- 100 100 000 - 30 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 170 Bad_Blk_Ct_Lat/Erl PO---- 100 100 000 - 0/112 173 MaxAvgErase_Ct -O--C- 100 100 000 - 1 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 6 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 CRC_Error_Count PO-R-- 100 100 050 - 0 231 SSD_Life_Left PO--C- 100 100 000 - 100 241 Lifetime_Writes_GiB -O--C- 100 100 000 - 174 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 30 --- Lifetime Power-On Resets 0x01 0x010 4 137 --- Power-on Hours 0x01 0x018 6 366833381 --- Logical Sectors Written 0x01 0x028 6 313725845 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 217 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 13 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.6-300.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue (CMR) Device Model: WDC WD10EZEX-00KUWA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 15.01H15 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database 7.5/5706 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 25 17:34:45 2025 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x30b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 3478 3 Spin_Up_Time POS--K 173 169 021 - 2316 4 Start_Stop_Count -O--CK 097 097 000 - 3535 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 074 074 000 - 19056 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2925 192 Power-Off_Retract_Count -O--CK 200 200 000 - 417 193 Load_Cycle_Count -O--CK 199 199 000 - 3117 194 Temperature_Celsius -O---K 114 088 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 4 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 8 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 3437 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3437 [4] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 0f 40 00 Error: UNC at LBA = 0x00724c0f = 7490575 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 30 00 00 00 72 4c 0f 40 00 00:11:10.683 READ FPDMA QUEUED 61 00 08 00 28 00 00 09 32 3c c8 40 00 00:11:10.683 WRITE FPDMA QUEUED 60 00 08 00 20 00 00 27 db c2 08 40 00 00:11:10.671 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:11:10.670 READ LOG EXT 60 00 08 00 18 00 00 27 db c2 48 40 00 00:11:06.713 READ FPDMA QUEUED Error 3436 [3] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 0e 40 00 Error: UNC at LBA = 0x00724c0e = 7490574 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 27 db c2 48 40 00 00:11:06.713 READ FPDMA QUEUED 60 00 01 00 10 00 00 00 72 4c 0e 40 00 00:11:06.712 READ FPDMA QUEUED 60 00 08 00 08 00 00 27 db c1 e8 40 00 00:11:06.700 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 00 00:11:06.641 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:11:06.641 READ LOG EXT Error 3435 [2] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 0d 40 00 Error: UNC at LBA = 0x00724c0d = 7490573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 f0 00 00 00 72 4c 0d 40 00 00:11:02.729 READ FPDMA QUEUED 61 00 08 00 e8 00 00 09 2e e1 50 40 00 00:11:02.729 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:11:02.729 READ LOG EXT 60 00 01 00 e0 00 00 00 72 4c 0c 40 00 00:10:58.807 READ FPDMA QUEUED 60 00 08 00 d0 00 00 0e d4 ff d8 40 00 00:10:58.799 READ FPDMA QUEUED Error 3434 [1] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 0c 40 00 Error: UNC at LBA = 0x00724c0c = 7490572 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 e0 00 00 00 72 4c 0c 40 00 00:10:58.807 READ FPDMA QUEUED 60 00 08 00 d0 00 00 0e d4 ff d8 40 00 00:10:58.799 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:10:58.799 READ LOG EXT 60 00 01 00 d8 00 00 00 72 4c 0b 40 00 00:10:54.854 READ FPDMA QUEUED 60 00 08 00 d0 00 00 0e d4 ff d8 40 00 00:10:54.853 READ FPDMA QUEUED Error 3433 [0] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 0b 40 00 Error: UNC at LBA = 0x00724c0b = 7490571 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 d8 00 00 00 72 4c 0b 40 00 00:10:54.854 READ FPDMA QUEUED 60 00 08 00 d0 00 00 0e d4 ff d8 40 00 00:10:54.853 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:10:54.853 READ LOG EXT 60 00 01 00 c8 00 00 00 72 4c 0a 40 00 00:10:50.932 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:10:50.932 READ LOG EXT Error 3432 [23] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 0a 40 00 Error: UNC at LBA = 0x00724c0a = 7490570 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 c8 00 00 00 72 4c 0a 40 00 00:10:50.932 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:10:50.932 READ LOG EXT 60 00 01 00 c0 00 00 00 72 4c 09 40 00 00:10:47.020 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:10:47.019 READ LOG EXT 60 00 01 00 b8 00 00 00 72 4c 08 40 00 00:10:43.089 READ FPDMA QUEUED Error 3431 [22] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 09 40 00 Error: UNC at LBA = 0x00724c09 = 7490569 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 c0 00 00 00 72 4c 09 40 00 00:10:47.020 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:10:47.019 READ LOG EXT 60 00 01 00 b8 00 00 00 72 4c 08 40 00 00:10:43.089 READ FPDMA QUEUED 60 00 01 00 b0 00 00 00 72 4c 07 40 00 00:10:43.089 READ FPDMA QUEUED 60 00 01 00 a8 00 00 00 72 4c 06 40 00 00:10:43.089 READ FPDMA QUEUED Error 3430 [21] occurred at disk power-on lifetime: 17602 hours (733 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 72 4c 08 40 00 Error: UNC at LBA = 0x00724c08 = 7490568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 b8 00 00 00 72 4c 08 40 00 00:10:43.089 READ FPDMA QUEUED 60 00 01 00 b0 00 00 00 72 4c 07 40 00 00:10:43.089 READ FPDMA QUEUED 60 00 01 00 a8 00 00 00 72 4c 06 40 00 00:10:43.089 READ FPDMA QUEUED 60 00 01 00 a0 00 00 00 72 4c 05 40 00 00:10:43.089 READ FPDMA QUEUED 60 00 01 00 98 00 00 00 72 4c 04 40 00 00:10:43.089 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 18901 - # 2 Short offline Completed without error 00% 17604 - # 3 Extended offline Completed: read failure 90% 17603 3198680 # 4 Short offline Completed: read failure 90% 17603 3198680 # 5 Conveyance offline Completed: read failure 90% 17600 3198680 # 6 Short offline Completed: read failure 90% 17600 3198680 # 7 Extended offline Completed: read failure 90% 17600 3198680 # 8 Short offline Completed: read failure 90% 17599 3198680 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 17/29 Celsius Lifetime Min/Max Temperature: 0/55 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (35) Index Estimated Time Temperature Celsius 36 2025-05-25 09:37 32 ************* ... ..( 14 skipped). .. ************* 51 2025-05-25 09:52 32 ************* 52 2025-05-25 09:53 31 ************ ... ..( 93 skipped). .. ************ 146 2025-05-25 11:27 31 ************ 147 2025-05-25 11:28 30 *********** ... ..(122 skipped). .. *********** 270 2025-05-25 13:31 30 *********** 271 2025-05-25 13:32 31 ************ ... ..( 29 skipped). .. ************ 301 2025-05-25 14:02 31 ************ 302 2025-05-25 14:03 30 *********** ... ..( 71 skipped). .. *********** 374 2025-05-25 15:15 30 *********** 375 2025-05-25 15:16 ? - 376 2025-05-25 15:17 17 - 377 2025-05-25 15:18 17 - 378 2025-05-25 15:19 17 - 379 2025-05-25 15:20 18 - 380 2025-05-25 15:21 19 - 381 2025-05-25 15:22 19 - 382 2025-05-25 15:23 20 * 383 2025-05-25 15:24 21 ** 384 2025-05-25 15:25 21 ** 385 2025-05-25 15:26 22 *** 386 2025-05-25 15:27 22 *** 387 2025-05-25 15:28 23 **** 388 2025-05-25 15:29 23 **** 389 2025-05-25 15:30 24 ***** 390 2025-05-25 15:31 24 ***** 391 2025-05-25 15:32 24 ***** 392 2025-05-25 15:33 25 ****** 393 2025-05-25 15:34 25 ****** 394 2025-05-25 15:35 25 ****** 395 2025-05-25 15:36 26 ******* 396 2025-05-25 15:37 26 ******* 397 2025-05-25 15:38 27 ******** ... ..( 3 skipped). .. ******** 401 2025-05-25 15:42 27 ******** 402 2025-05-25 15:43 28 ********* ... ..( 3 skipped). .. ********* 406 2025-05-25 15:47 28 ********* 407 2025-05-25 15:48 29 ********** 408 2025-05-25 15:49 33 ************** ... ..( 7 skipped). .. ************** 416 2025-05-25 15:57 33 ************** 417 2025-05-25 15:58 32 ************* ... ..( 95 skipped). .. ************* 35 2025-05-25 17:34 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1905 Vendor specific /dev/sdc smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.6-300.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT500MX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M3CR022 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.5/5706 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 25 17:34:45 2025 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 13557 12 Power_Cycle_Count -O--CK 100 100 000 - 3041 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 087 087 000 - 199 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 214 180 Unused_Reserve_NAND_Blk PO--CK 000 000 000 - 42 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 069 037 000 - 31 (Min/Max 0/63) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 4 202 Percent_Lifetime_Remain ----CK 087 087 001 - 13 206 Write_Error_Rate -OSR-- 100 100 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 41636258893 247 Host_Program_Page_Count -O--CK 100 100 000 - 698421417 248 FTL_Program_Page_Count -O--CK 100 100 000 - 1627410980 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 64 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Completed [00% left] (0-65535) Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 18/31 Celsius Lifetime Min/Max Temperature: 0/63 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: 0/100 Celsius Temperature History Size (Index): 128 (102) Index Estimated Time Temperature Celsius 103 2025-05-25 15:27 33 ************** ... ..( 2 skipped). .. ************** 106 2025-05-25 15:30 33 ************** 107 2025-05-25 15:31 ? - 108 2025-05-25 15:32 ? - 109 2025-05-25 15:33 23 **** 110 2025-05-25 15:34 28 ********* 111 2025-05-25 15:35 30 *********** ... ..( 2 skipped). .. *********** 114 2025-05-25 15:38 30 *********** 115 2025-05-25 15:39 31 ************ ... ..( 25 skipped). .. ************ 13 2025-05-25 16:05 31 ************ 14 2025-05-25 16:06 ? - 15 2025-05-25 16:07 ? - 16 2025-05-25 16:08 23 **** 17 2025-05-25 16:09 28 ********* 18 2025-05-25 16:10 30 *********** 19 2025-05-25 16:11 30 *********** 20 2025-05-25 16:12 31 ************ ... ..( 8 skipped). .. ************ 29 2025-05-25 16:21 31 ************ 30 2025-05-25 16:22 33 ************** 31 2025-05-25 16:23 35 **************** 32 2025-05-25 16:24 35 **************** 33 2025-05-25 16:25 36 ***************** ... ..( 3 skipped). .. ***************** 37 2025-05-25 16:29 36 ***************** 38 2025-05-25 16:30 35 **************** 39 2025-05-25 16:31 36 ***************** 40 2025-05-25 16:32 33 ************** 41 2025-05-25 16:33 33 ************** 42 2025-05-25 16:34 31 ************ ... ..( 14 skipped). .. ************ 57 2025-05-25 16:49 31 ************ 58 2025-05-25 16:50 30 *********** 59 2025-05-25 16:51 31 ************ 60 2025-05-25 16:52 31 ************ 61 2025-05-25 16:53 30 *********** ... ..( 2 skipped). .. *********** 64 2025-05-25 16:56 30 *********** 65 2025-05-25 16:57 31 ************ 66 2025-05-25 16:58 31 ************ 67 2025-05-25 16:59 33 ************** 68 2025-05-25 17:00 33 ************** 69 2025-05-25 17:01 30 *********** 70 2025-05-25 17:02 30 *********** 71 2025-05-25 17:03 31 ************ 72 2025-05-25 17:04 30 *********** ... ..( 6 skipped). .. *********** 79 2025-05-25 17:11 30 *********** 80 2025-05-25 17:12 31 ************ 81 2025-05-25 17:13 31 ************ 82 2025-05-25 17:14 30 *********** 83 2025-05-25 17:15 30 *********** 84 2025-05-25 17:16 33 ************** 85 2025-05-25 17:17 31 ************ 86 2025-05-25 17:18 33 ************** 87 2025-05-25 17:19 33 ************** 88 2025-05-25 17:20 33 ************** 89 2025-05-25 17:21 30 *********** ... ..( 5 skipped). .. *********** 95 2025-05-25 17:27 30 *********** 96 2025-05-25 17:28 ? - 97 2025-05-25 17:29 ? - 98 2025-05-25 17:30 26 ******* 99 2025-05-25 17:31 30 *********** 100 2025-05-25 17:32 30 *********** 101 2025-05-25 17:33 31 ************ 102 2025-05-25 17:34 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3041 --- Lifetime Power-On Resets 0x01 0x010 4 13557 --- Power-on Hours 0x01 0x018 6 2981553229 --- Logical Sectors Written 0x01 0x020 6 611886668 --- Number of Write Commands 0x01 0x028 6 2038029710 --- Logical Sectors Read 0x01 0x030 6 1248903206 --- Number of Read Commands 0x01 0x038 6 4294967296 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 219 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x010 1 31 --- Average Short Term Temperature 0x05 0x018 1 31 --- Average Long Term Temperature 0x05 0x020 1 63 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 52 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 41 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 39 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 44071 --- Number of Hardware Resets 0x06 0x010 4 3951 --- Number of ASR Events 0x06 0x018 4 4 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 13 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdd smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.14.6-300.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue (CMR) Device Model: WDC WD10EZEX-00BN5A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.5/5706 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 25 17:34:45 2025 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 115) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 173 167 021 - 2341 4 Start_Stop_Count -O--CK 090 090 000 - 10260 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 062 062 000 - 28294 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4623 192 Power-Off_Retract_Count -O--CK 200 200 000 - 588 193 Load_Cycle_Count -O--CK 197 197 000 - 9671 194 Temperature_Celsius -O---K 116 089 000 - 27 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 9576 hours (399 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 51 38 70 28 40 00 Error: UNC at LBA = 0x51387028 = 1362653224 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 c0 00 00 51 37 d1 18 40 00 00:40:21.707 READ FPDMA QUEUED 60 01 00 00 b8 00 00 51 37 d0 18 40 00 00:40:21.707 READ FPDMA QUEUED 60 01 00 00 b0 00 00 51 37 cf 18 40 00 00:40:21.707 READ FPDMA QUEUED 60 01 00 00 a8 00 00 51 37 ce 18 40 00 00:40:21.707 READ FPDMA QUEUED 60 01 00 00 a0 00 00 51 37 cd 18 40 00 00:40:21.707 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 17/27 Celsius Lifetime Min/Max Temperature: 0/54 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (214) Index Estimated Time Temperature Celsius 215 2025-05-25 09:37 28 ********* ... ..( 82 skipped). .. ********* 298 2025-05-25 11:00 28 ********* 299 2025-05-25 11:01 27 ******** ... ..(117 skipped). .. ******** 417 2025-05-25 12:59 27 ******** 418 2025-05-25 13:00 28 ********* ... ..( 19 skipped). .. ********* 438 2025-05-25 13:20 28 ********* 439 2025-05-25 13:21 27 ******** ... ..( 65 skipped). .. ******** 27 2025-05-25 14:27 27 ******** 28 2025-05-25 14:28 26 ******* ... ..( 18 skipped). .. ******* 47 2025-05-25 14:47 26 ******* 48 2025-05-25 14:48 ? - 49 2025-05-25 14:49 17 - 50 2025-05-25 14:50 17 - 51 2025-05-25 14:51 18 - 52 2025-05-25 14:52 18 - 53 2025-05-25 14:53 19 - 54 2025-05-25 14:54 20 * 55 2025-05-25 14:55 20 * 56 2025-05-25 14:56 21 ** 57 2025-05-25 14:57 21 ** 58 2025-05-25 14:58 22 *** 59 2025-05-25 14:59 22 *** 60 2025-05-25 15:00 23 **** 61 2025-05-25 15:01 23 **** 62 2025-05-25 15:02 23 **** 63 2025-05-25 15:03 24 ***** 64 2025-05-25 15:04 24 ***** 65 2025-05-25 15:05 24 ***** 66 2025-05-25 15:06 25 ****** ... ..( 4 skipped). .. ****** 71 2025-05-25 15:11 25 ****** 72 2025-05-25 15:12 26 ******* ... ..( 5 skipped). .. ******* 78 2025-05-25 15:18 26 ******* 79 2025-05-25 15:19 27 ******** 80 2025-05-25 15:20 27 ******** 81 2025-05-25 15:21 29 ********** ... ..( 27 skipped). .. ********** 109 2025-05-25 15:49 29 ********** 110 2025-05-25 15:50 28 ********* ... ..(103 skipped). .. ********* 214 2025-05-25 17:34 28 ********* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1905 Vendor specific