/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.15.9-x64v3-xanmod1] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: HGST Travelstar Z5K1000 Device Model: HGST HTS541010A7E630 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: SE0OA4G0 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Aug 2 18:35:05 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 216) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 097 062 - 0 2 Throughput_Performance P-S--K 100 100 040 - 0 3 Spin_Up_Time PO---K 161 100 033 - 1 4 Start_Stop_Count -O--CK 092 092 000 - 13081 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 100 100 040 - 0 9 Power_On_Hours -O--CK 052 052 000 - 21400 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 2980 183 Runtime_Bad_Block -O--CK 100 100 001 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 42952949776 188 Command_Timeout -O--CK 100 100 000 - 854714220545 190 Airflow_Temperature_Cel -O---K 060 043 045 Past 40 (Min/Max 22/40) 191 G-Sense_Error_Rate -O--CK 001 001 000 - 256884 192 Power-Off_Retract_Count -O--CK 100 100 000 - 8913032 193 Load_Cycle_Count -O--CK 092 092 000 - 85844 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 16 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 16 [3] occurred at disk power-on lifetime: 13826 hours (576 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 3c 4a 38 18 0c 00 Error: UNC at LBA = 0x3c4a3818 = 1011496984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 68 00 00 3c 4a 37 20 40 00 00:17:07.765 READ FPDMA QUEUED 60 01 00 00 60 00 00 3c 4a 36 20 40 00 00:17:04.463 READ FPDMA QUEUED 60 01 00 00 58 00 00 3c 4a 35 20 40 00 00:16:57.978 READ FPDMA QUEUED 60 01 00 00 50 00 00 3c 4a 34 20 40 00 00:16:57.978 READ FPDMA QUEUED 61 00 20 00 48 00 00 42 47 22 60 40 00 00:16:57.978 WRITE FPDMA QUEUED Error 15 [2] occurred at disk power-on lifetime: 13826 hours (576 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 00 3c 4a 2d f8 0c 00 Error: UNC at LBA = 0x3c4a2df8 = 1011494392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 f8 00 00 3c 4a 2e 20 40 00 00:16:32.914 READ FPDMA QUEUED 60 01 00 00 f0 00 00 3c 4a 2d 20 40 00 00:16:32.914 READ FPDMA QUEUED 60 01 00 00 e8 00 00 3c 4a 2c 20 40 00 00:16:32.914 READ FPDMA QUEUED 60 01 00 00 d0 00 00 3c 4a 2b 20 40 00 00:16:32.914 READ FPDMA QUEUED 60 01 00 00 48 00 00 3c 4a 2a 20 40 00 00:16:32.914 READ FPDMA QUEUED Error 14 [1] occurred at disk power-on lifetime: 13826 hours (576 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 d8 00 00 3c 4a 29 48 0c 00 Error: UNC at LBA = 0x3c4a2948 = 1011493192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 f0 00 00 3c 4a 2d 20 40 00 00:16:24.573 READ FPDMA QUEUED 60 01 00 00 e8 00 00 3c 4a 2c 20 40 00 00:16:24.573 READ FPDMA QUEUED 60 01 00 00 d0 00 00 3c 4a 2b 20 40 00 00:16:24.573 READ FPDMA QUEUED 60 01 00 00 48 00 00 3c 4a 2a 20 40 00 00:16:24.573 READ FPDMA QUEUED 60 01 00 00 40 00 00 3c 4a 29 20 40 00 00:16:24.573 READ FPDMA QUEUED Error 13 [0] occurred at disk power-on lifetime: 13826 hours (576 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 10 00 00 3c 4a 28 10 0c 00 Error: UNC at LBA = 0x3c4a2810 = 1011492880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 f0 00 00 3c 4a 23 20 40 00 00:16:16.213 READ FPDMA QUEUED 60 01 00 00 e8 00 00 3c 4a 2c 20 40 00 00:16:16.213 READ FPDMA QUEUED 60 01 00 00 e0 00 00 3c 4a 22 20 40 00 00:16:16.213 READ FPDMA QUEUED 60 01 00 00 d8 00 00 3c 4a 21 20 40 00 00:16:16.213 READ FPDMA QUEUED 60 01 00 00 d0 00 00 3c 4a 2b 20 40 00 00:16:16.213 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 20466 - # 2 Short offline Completed without error 00% 20458 - # 3 Short offline Completed without error 00% 20409 - # 4 Short offline Completed without error 00% 20369 - # 5 Short offline Completed without error 00% 20148 - # 6 Short offline Completed without error 00% 20113 - # 7 Short offline Completed without error 00% 20105 - # 8 Short offline Completed without error 00% 20034 - # 9 Extended offline Interrupted (host reset) 80% 9617 - #10 Short offline Completed without error 00% 9616 - #11 Short offline Completed without error 00% 7978 - #12 Short offline Completed without error 00% 6798 - #13 Short offline Completed without error 00% 6193 - #14 Short offline Completed without error 00% 2 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 22/40 Celsius Lifetime Min/Max Temperature: 8/57 Celsius Specified Max Operating Temperature: 35 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (60) Index Estimated Time Temperature Celsius 61 2025-08-02 16:28 34 *************** 62 2025-08-02 16:29 33 ************** ... ..( 10 skipped). .. ************** 73 2025-08-02 16:40 33 ************** 74 2025-08-02 16:41 32 ************* 75 2025-08-02 16:42 32 ************* 76 2025-08-02 16:43 32 ************* 77 2025-08-02 16:44 31 ************ ... ..( 5 skipped). .. ************ 83 2025-08-02 16:50 31 ************ 84 2025-08-02 16:51 30 *********** 85 2025-08-02 16:52 31 ************ ... ..( 3 skipped). .. ************ 89 2025-08-02 16:56 31 ************ 90 2025-08-02 16:57 30 *********** ... ..( 5 skipped). .. *********** 96 2025-08-02 17:03 30 *********** 97 2025-08-02 17:04 31 ************ 98 2025-08-02 17:05 30 *********** ... ..( 17 skipped). .. *********** 116 2025-08-02 17:23 30 *********** 117 2025-08-02 17:24 31 ************ 118 2025-08-02 17:25 31 ************ 119 2025-08-02 17:26 30 *********** 120 2025-08-02 17:27 31 ************ 121 2025-08-02 17:28 30 *********** 122 2025-08-02 17:29 31 ************ ... ..( 14 skipped). .. ************ 9 2025-08-02 17:44 31 ************ 10 2025-08-02 17:45 32 ************* ... ..( 9 skipped). .. ************* 20 2025-08-02 17:55 32 ************* 21 2025-08-02 17:56 33 ************** 22 2025-08-02 17:57 33 ************** 23 2025-08-02 17:58 32 ************* 24 2025-08-02 17:59 33 ************** 25 2025-08-02 18:00 33 ************** 26 2025-08-02 18:01 34 *************** 27 2025-08-02 18:02 34 *************** 28 2025-08-02 18:03 35 **************** 29 2025-08-02 18:04 35 **************** 30 2025-08-02 18:05 36 ***************** 31 2025-08-02 18:06 37 ****************** ... ..( 5 skipped). .. ****************** 37 2025-08-02 18:12 37 ****************** 38 2025-08-02 18:13 38 ******************* ... ..( 7 skipped). .. ******************* 46 2025-08-02 18:21 38 ******************* 47 2025-08-02 18:22 39 ******************** ... ..( 12 skipped). .. ******************** 60 2025-08-02 18:35 39 ******************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 5305 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS