/dev/nvme0n1 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-40-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: SAMSUNG MZVLQ1T0HALB-00000 Serial Number: -- Firmware Version: FXV7101Q PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 1,024,209,543,168 [1.02 TB] Unallocated NVM Capacity: 0 Controller ID: 5 Number of Namespaces: 1 Namespace 1 Size/Capacity: 1,024,209,543,168 [1.02 TB] Namespace 1 Utilization: 506,266,402,816 [506 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Fri May 6 00:43:55 2022 CEST Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x005f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 82 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 4.83W - - 0 0 0 0 0 0 1 + 3.54W - - 1 1 1 1 0 0 2 + 3.04W - - 2 2 2 2 0 500 3 - 0.0500W - - 3 3 3 3 210 1200 4 - 0.0050W - - 4 4 4 4 1000 9000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 30 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 2,465,583 [1.26 TB] Data Units Written: 2,296,133 [1.17 TB] Host Read Commands: 17,713,895 Host Write Commands: 10,498,465 Controller Busy Time: 96 Power Cycles: 87 Power On Hours: 58 Unsafe Shutdowns: 34 Media and Data Integrity Errors: 0 Error Information Log Entries: 388 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 30 Celsius Error Information (NVMe Log 0x01, max 64 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 388 0 0x201c 0x4004 - 0 0 - /dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-40-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST500LM012 HN-M500MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2BA30001 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 6 00:43:55 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6420) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 107) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 1 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 093 025 - 2164 4 Start_Stop_Count -O--CK 099 099 000 - 1234 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 2935 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 1 12 Power_Cycle_Count -O--CK 100 100 000 - 869 191 G-Sense_Error_Rate -O---K 252 252 000 - 0 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 057 000 - 28 (Min/Max 13/43) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 326 223 Load_Retry_Count -O--CK 100 100 000 - 1 225 Load_Cycle_Count -O--CK 099 099 000 - 17895 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 16/28 Celsius Lifetime Min/Max Temperature: 13/43 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (25) Index Estimated Time Temperature Celsius 26 2022-05-05 14:05 28 ********* 27 2022-05-05 14:10 26 ******* 28 2022-05-05 14:15 26 ******* 29 2022-05-05 14:20 26 ******* 30 2022-05-05 14:25 24 ***** 31 2022-05-05 14:30 22 *** 32 2022-05-05 14:35 24 ***** 33 2022-05-05 14:40 24 ***** 34 2022-05-05 14:45 23 **** 35 2022-05-05 14:50 19 - 36 2022-05-05 14:55 22 *** 37 2022-05-05 15:00 23 **** 38 2022-05-05 15:05 24 ***** 39 2022-05-05 15:10 25 ****** 40 2022-05-05 15:15 26 ******* 41 2022-05-05 15:20 27 ******** ... ..( 13 skipped). .. ******** 55 2022-05-05 16:30 27 ******** 56 2022-05-05 16:35 28 ********* ... ..( 4 skipped). .. ********* 61 2022-05-05 17:00 28 ********* 62 2022-05-05 17:05 27 ******** 63 2022-05-05 17:10 27 ******** 64 2022-05-05 17:15 18 - 65 2022-05-05 17:20 20 * 66 2022-05-05 17:25 22 *** 67 2022-05-05 17:30 23 **** 68 2022-05-05 17:35 24 ***** 69 2022-05-05 17:40 25 ****** 70 2022-05-05 17:45 25 ****** 71 2022-05-05 17:50 25 ****** 72 2022-05-05 17:55 26 ******* ... ..( 3 skipped). .. ******* 76 2022-05-05 18:15 26 ******* 77 2022-05-05 18:20 27 ******** ... ..( 2 skipped). .. ******** 80 2022-05-05 18:35 27 ******** 81 2022-05-05 18:40 28 ********* 82 2022-05-05 18:45 27 ******** 83 2022-05-05 18:50 28 ********* 84 2022-05-05 18:55 28 ********* 85 2022-05-05 19:00 28 ********* 86 2022-05-05 19:05 27 ******** 87 2022-05-05 19:10 27 ******** 88 2022-05-05 19:15 28 ********* ... ..( 2 skipped). .. ********* 91 2022-05-05 19:30 28 ********* 92 2022-05-05 19:35 27 ******** 93 2022-05-05 19:40 19 - 94 2022-05-05 19:45 23 **** 95 2022-05-05 19:50 24 ***** 96 2022-05-05 19:55 25 ****** 97 2022-05-05 20:00 25 ****** 98 2022-05-05 20:05 26 ******* ... ..( 3 skipped). .. ******* 102 2022-05-05 20:25 26 ******* 103 2022-05-05 20:30 27 ******** ... ..( 7 skipped). .. ******** 111 2022-05-05 21:10 27 ******** 112 2022-05-05 21:15 26 ******* 113 2022-05-05 21:20 26 ******* 114 2022-05-05 21:25 27 ******** 115 2022-05-05 21:30 27 ******** 116 2022-05-05 21:35 18 - 117 2022-05-05 21:40 21 ** 118 2022-05-05 21:45 22 *** 119 2022-05-05 21:50 23 **** 120 2022-05-05 21:55 24 ***** 121 2022-05-05 22:00 25 ****** 122 2022-05-05 22:05 25 ****** 123 2022-05-05 22:10 26 ******* ... ..( 2 skipped). .. ******* 126 2022-05-05 22:25 26 ******* 127 2022-05-05 22:30 27 ******** ... ..( 13 skipped). .. ******** 13 2022-05-05 23:40 27 ******** 14 2022-05-05 23:45 28 ********* ... ..( 10 skipped). .. ********* 25 2022-05-06 00:40 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 4007 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 15 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-40-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD10SDRW-11A0XS1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,171,331,584 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 6 00:43:55 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8700) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 143) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 165 159 021 - 2708 4 Start_Stop_Count -O--CK 100 100 000 - 883 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 099 099 000 - 796 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 268 192 Power-Off_Retract_Count -O--CK 200 200 000 - 186 193 Load_Cycle_Count -O--CK 200 200 000 - 1788 194 Temperature_Celsius -O---K 108 093 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 74 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xcf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 34/35 Celsius Lifetime Min/Max Temperature: 10/50 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (19) Index Estimated Time Temperature Celsius 20 2022-05-05 22:36 33 ************** 21 2022-05-05 22:37 33 ************** 22 2022-05-05 22:38 33 ************** 23 2022-05-05 22:39 32 ************* ... ..( 11 skipped). .. ************* 35 2022-05-05 22:51 32 ************* 36 2022-05-05 22:52 31 ************ ... ..( 6 skipped). .. ************ 43 2022-05-05 22:59 31 ************ 44 2022-05-05 23:00 30 *********** ... ..( 18 skipped). .. *********** 63 2022-05-05 23:19 30 *********** 64 2022-05-05 23:20 ? - 65 2022-05-05 23:21 30 *********** 66 2022-05-05 23:22 ? - 67 2022-05-05 23:23 32 ************* ... ..( 3 skipped). .. ************* 71 2022-05-05 23:27 32 ************* 72 2022-05-05 23:28 33 ************** ... ..( 10 skipped). .. ************** 83 2022-05-05 23:39 33 ************** 84 2022-05-05 23:40 34 *************** ... ..( 12 skipped). .. *************** 97 2022-05-05 23:53 34 *************** 98 2022-05-05 23:54 ? - 99 2022-05-05 23:55 34 *************** 100 2022-05-05 23:56 34 *************** 101 2022-05-05 23:57 ? - 102 2022-05-05 23:58 34 *************** ... ..( 4 skipped). .. *************** 107 2022-05-06 00:03 34 *************** 108 2022-05-06 00:04 35 **************** ... ..( 2 skipped). .. **************** 111 2022-05-06 00:07 35 **************** 112 2022-05-06 00:08 ? - 113 2022-05-06 00:09 35 **************** ... ..( 5 skipped). .. **************** 119 2022-05-06 00:15 35 **************** 120 2022-05-06 00:16 ? - 121 2022-05-06 00:17 35 **************** 122 2022-05-06 00:18 ? - 123 2022-05-06 00:19 35 **************** ... ..( 9 skipped). .. **************** 5 2022-05-06 00:29 35 **************** 6 2022-05-06 00:30 34 *************** ... ..( 3 skipped). .. *************** 10 2022-05-06 00:34 34 *************** 11 2022-05-06 00:35 35 **************** 12 2022-05-06 00:36 34 *************** 13 2022-05-06 00:37 34 *************** 14 2022-05-06 00:38 35 **************** 15 2022-05-06 00:39 34 *************** 16 2022-05-06 00:40 34 *************** 17 2022-05-06 00:41 34 *************** 18 2022-05-06 00:42 35 **************** 19 2022-05-06 00:43 35 **************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1816 Vendor specific