/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.8-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST1000LM024 HN-M101MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2BA30001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jul 13 08:12:11 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Disabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (13560) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 226) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 9695 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 091 025 - 2352 4 Start_Stop_Count -O--CK 099 099 000 - 1318 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 1564 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 130 12 Power_Cycle_Count -O--CK 099 099 000 - 1156 191 G-Sense_Error_Rate -O---K 100 100 000 - 58 192 Power-Off_Retract_Count -O---K 100 100 000 - 121 194 Temperature_Celsius -O---- 064 055 000 - 22 (Min/Max 0/54) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 1 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 1751 223 Load_Retry_Count -O--CK 100 100 000 - 130 225 Load_Cycle_Count -O--CK 095 095 000 - 59680 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 9669 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9669 [4] occurred at disk power-on lifetime: 1562 hours (65 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 19 00 00 73 32 a6 88 40 00 Error: UNC 25 sectors at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 3d 00 00 73 32 a6 64 40 00 00:00:00.010 READ DMA EXT 25 00 00 00 20 00 00 38 7c 3f 80 40 00 00:00:00.010 READ DMA EXT 25 00 00 00 08 00 00 00 ad 40 f0 40 00 00:00:00.010 READ DMA EXT 25 00 00 00 20 00 00 38 7c 3f 60 40 00 00:00:00.010 READ DMA EXT 25 00 00 00 08 00 00 05 cc 34 20 40 00 00:00:00.010 READ DMA EXT Error 9668 [3] occurred at disk power-on lifetime: 1562 hours (65 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 19 00 00 73 32 a6 88 40 00 Error: UNC at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 3d 00 00 73 32 a6 64 40 00 00:00:00.055 READ FPDMA QUEUED 60 00 02 00 50 00 00 03 c6 74 f8 40 00 00:00:00.076 READ FPDMA QUEUED 60 00 02 00 80 00 00 03 c6 75 48 40 00 00:00:00.076 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 a5 c9 a8 40 00 00:00:00.076 WRITE FPDMA QUEUED 60 00 00 00 3d 00 00 73 32 a6 64 40 00 00:00:00.076 READ FPDMA QUEUED Error 9667 [2] occurred at disk power-on lifetime: 1562 hours (65 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 19 00 00 73 32 a6 88 40 00 Error: UNC at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 50 00 00 03 c6 74 f8 40 00 00:00:00.058 READ FPDMA QUEUED 60 00 02 00 3d 00 00 73 32 a6 64 40 00 00:00:00.055 READ FPDMA QUEUED 60 00 02 00 3d 00 00 73 32 a6 64 40 00 00:00:00.056 READ FPDMA QUEUED 60 00 02 00 02 00 00 73 32 a6 62 40 00 00:00:00.056 READ FPDMA QUEUED 60 00 02 00 02 00 00 73 32 a6 60 40 00 00:00:00.056 READ FPDMA QUEUED Error 9666 [1] occurred at disk power-on lifetime: 1562 hours (65 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 19 00 00 73 32 a6 88 40 00 Error: UNC at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 3d 00 00 73 32 a6 64 40 00 00:00:00.060 READ FPDMA QUEUED 60 00 03 00 3d 00 00 73 32 a6 64 40 00 00:00:00.127 READ FPDMA QUEUED 60 00 03 00 20 00 00 38 7c 38 80 40 00 00:00:00.127 READ FPDMA QUEUED 61 00 03 00 08 00 00 00 0a 03 a0 40 00 00:00:00.127 WRITE FPDMA QUEUED 61 00 03 00 08 00 00 00 0a 72 68 40 00 00:00:00.127 WRITE FPDMA QUEUED Error 9665 [0] occurred at disk power-on lifetime: 1562 hours (65 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 19 00 00 73 32 a6 88 40 00 Error: UNC at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 08 00 00 02 8b 7e e8 40 00 00:00:00.113 READ FPDMA QUEUED 60 00 03 00 3d 00 00 73 32 a6 64 40 00 00:00:00.060 READ FPDMA QUEUED 61 00 03 00 10 00 00 70 10 b9 d0 40 00 00:00:00.110 WRITE FPDMA QUEUED 60 00 03 00 20 00 00 38 7c 38 80 40 00 00:00:00.110 READ FPDMA QUEUED 60 00 03 00 3d 00 00 73 32 a6 64 40 00 00:00:00.110 READ FPDMA QUEUED Error 9664 [7] occurred at disk power-on lifetime: 1561 hours (65 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 19 00 00 73 32 a6 88 e0 00 Error: UNC 25 sectors at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 3d 00 00 73 32 a6 64 e0 00 00:00:00.113 READ DMA EXT 25 00 00 00 02 00 00 73 32 a6 62 e0 00 00:00:00.113 READ DMA EXT 25 00 00 00 20 00 00 38 7c 34 20 e0 00 00:00:00.113 READ DMA EXT 25 00 00 00 08 00 00 06 cc 22 60 e0 00 00:00:00.113 READ DMA EXT 25 00 00 00 10 00 00 00 00 00 00 e0 00 00:00:00.113 READ DMA EXT Error 9663 [6] occurred at disk power-on lifetime: 1561 hours (65 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 19 00 00 73 32 a6 88 e0 00 Error: UNC 25 sectors at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 3d 00 00 73 32 a6 64 e0 00 00:00:00.020 READ DMA EXT 25 00 00 00 20 00 00 38 7c 31 20 e0 00 00:00:00.020 READ DMA EXT 25 00 00 00 02 00 00 73 32 a6 62 e0 00 00:00:00.020 READ DMA EXT 25 00 00 00 20 00 00 38 7c 31 00 e0 00 00:00:00.020 READ DMA EXT 25 00 00 00 02 00 00 73 32 a6 60 e0 00 00:00:00.020 READ DMA EXT Error 9662 [5] occurred at disk power-on lifetime: 1560 hours (65 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 19 00 00 73 32 a6 88 e0 00 Error: UNC 25 sectors at LBA = 0x7332a688 = 1932699272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 3d 00 00 73 32 a6 64 e0 00 00:00:00.098 READ DMA EXT 25 00 00 00 02 00 00 73 32 a6 62 e0 00 00:00:00.098 READ DMA EXT 25 00 00 00 02 00 00 73 32 a6 60 e0 00 00:00:00.098 READ DMA EXT 25 00 00 00 08 00 00 73 32 f8 58 e0 00 00:00:00.098 READ DMA EXT 25 00 00 00 08 00 00 73 32 f8 40 e0 00 00:00:00.098 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 1563 1932699272 # 2 Short offline Completed: read failure 90% 1563 1932699272 # 3 Short offline Completed: read failure 90% 1563 1932699272 # 4 Short offline Completed: read failure 90% 1563 1932699272 # 5 Vendor (0x50) Completed without error 00% 1425 - # 6 Short offline Completed: read failure 90% 1425 1932699272 # 7 Vendor (0x50) Completed without error 00% 1115 - # 8 Short offline Completed: read failure 90% 1115 1932699272 # 9 Vendor (0x50) Completed without error 00% 1045 - #10 Short offline Completed: read failure 70% 1045 1932699272 #11 Vendor (0x50) Completed without error 00% 981 - #12 Short offline Completed: read failure 90% 981 1932699272 #13 Vendor (0x50) Completed without error 00% 925 - #14 Short offline Completed: read failure 90% 925 1932699272 #15 Vendor (0x50) Completed without error 00% 388 - #16 Short offline Completed: read failure 80% 388 1932699272 #17 Vendor (0x50) Completed without error 00% 166 - #18 Short offline Completed: read failure 90% 166 1932699272 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed_read_failure [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 21/22 Celsius Lifetime Min/Max Temperature: 0/54 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (43) Index Estimated Time Temperature Celsius 44 2024-07-12 21:35 22 *** 45 2024-07-12 21:40 26 ******* 46 2024-07-12 21:45 26 ******* 47 2024-07-12 21:50 26 ******* 48 2024-07-12 21:55 27 ******** ... ..( 7 skipped). .. ******** 56 2024-07-12 22:35 27 ******** 57 2024-07-12 22:40 28 ********* ... ..( 10 skipped). .. ********* 68 2024-07-12 23:35 28 ********* 69 2024-07-12 23:40 29 ********** ... ..( 38 skipped). .. ********** 108 2024-07-13 02:55 29 ********** 109 2024-07-13 03:00 28 ********* ... ..( 5 skipped). .. ********* 115 2024-07-13 03:30 28 ********* 116 2024-07-13 03:35 23 **** 117 2024-07-13 03:40 28 ********* 118 2024-07-13 03:45 31 ************ 119 2024-07-13 03:50 32 ************* 120 2024-07-13 03:55 34 *************** 121 2024-07-13 04:00 34 *************** 122 2024-07-13 04:05 34 *************** 123 2024-07-13 04:10 35 **************** 124 2024-07-13 04:15 32 ************* 125 2024-07-13 04:20 27 ******** 126 2024-07-13 04:25 28 ********* 127 2024-07-13 04:30 28 ********* 0 2024-07-13 04:35 28 ********* 1 2024-07-13 04:40 29 ********** 2 2024-07-13 04:45 30 *********** 3 2024-07-13 04:50 31 ************ 4 2024-07-13 04:55 32 ************* 5 2024-07-13 05:00 33 ************** 6 2024-07-13 05:05 33 ************** 7 2024-07-13 05:10 33 ************** 8 2024-07-13 05:15 32 ************* ... ..( 4 skipped). .. ************* 13 2024-07-13 05:40 32 ************* 14 2024-07-13 05:45 31 ************ 15 2024-07-13 05:50 31 ************ 16 2024-07-13 05:55 29 ********** 17 2024-07-13 06:00 29 ********** 18 2024-07-13 06:05 30 *********** 19 2024-07-13 06:10 32 ************* 20 2024-07-13 06:15 34 *************** 21 2024-07-13 06:20 36 ***************** 22 2024-07-13 06:25 39 ******************** 23 2024-07-13 06:30 38 ******************* 24 2024-07-13 06:35 39 ******************** 25 2024-07-13 06:40 40 ********************* 26 2024-07-13 06:45 38 ******************* 27 2024-07-13 06:50 23 **** 28 2024-07-13 06:55 26 ******* 29 2024-07-13 07:00 28 ********* 30 2024-07-13 07:05 29 ********** 31 2024-07-13 07:10 28 ********* 32 2024-07-13 07:15 28 ********* 33 2024-07-13 07:20 29 ********** 34 2024-07-13 07:25 29 ********** 35 2024-07-13 07:30 28 ********* 36 2024-07-13 07:35 28 ********* 37 2024-07-13 07:40 26 ******* 38 2024-07-13 07:45 21 ** 39 2024-07-13 07:50 19 - 40 2024-07-13 07:55 18 - 41 2024-07-13 08:00 18 - 42 2024-07-13 08:05 22 *** 43 2024-07-13 08:10 22 *** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.8-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: XrayDisk 480GB SSD Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: HPS2818B User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jul 13 08:12:12 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Disabled Write cache is: Disabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x00) Offline data collection not supported. SMART capabilities: (0x0000) Automatic saving of SMART data is not implemented. Error logging capability: (0x00) Error logging supported. General Purpose Logging supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 593 12 Power_Cycle_Count -O--CK 100 100 050 - 55 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute -O--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 350 164 Unknown_Attribute -O--CK 100 100 050 - 0 165 Unknown_Attribute -O--CK 100 100 050 - 0 166 Unknown_Attribute -O--CK 100 100 050 - 0 167 Unknown_Attribute -O--CK 100 100 050 - 0 168 Unknown_Attribute -O--CK 100 100 050 - 0 169 Unknown_Attribute -O--CK 100 100 050 - 100 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 2890 177 Wear_Leveling_Count -O--CK 100 100 050 - 69480 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 21 194 Temperature_Celsius -O--CK 100 100 050 - 41 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written -O--CK 100 100 050 - 9166 242 Total_LBAs_Read -O--CK 100 100 050 - 1854 245 Unknown_Attribute -O--CK 100 100 050 - 16805 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 0 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 55 --- Lifetime Power-On Resets 0x01 0x010 4 593 --- Power-on Hours 0x01 0x018 6 600702976 --- Logical Sectors Written 0x01 0x020 6 10904843 --- Number of Write Commands 0x01 0x028 6 121503744 --- Logical Sectors Read 0x01 0x030 6 2894906 --- Number of Read Commands |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0009 4 73 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 90 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS