/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Device Model: WDC WD800JB-00JJC0 Serial Number: -- Firmware Version: 05.01C05 User Capacity: 80 026 361 856 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 (minor revision not indicated) Local Time is: Sun Jan 24 20:54:49 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Unknown SCT Status format version 1, should be 2 or 3. Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 35) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 161 158 021 - 2941 4 Start_Stop_Count -O--CK 100 100 000 - 704 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 099 099 000 - 1139 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 638 194 Temperature_Celsius -O---K 108 089 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 1 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error aborted command ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: scsi error aborted command Read GP Log Directory failed SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Unknown SCT Status format version 1, should be 2 or 3. Unknown SCT Status format version 1, should be 2 or 3. SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Serial ATA Device Model: WDC WD800JD-00LSA0 Serial Number: -- Firmware Version: 06.01D06 User Capacity: 80 025 280 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Jan 24 20:54:49 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Write SCT (Get) Feature Control Command failed: scsi error aborted command Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 33) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 69 3 Spin_Up_Time PO---- 188 159 021 - 1566 4 Start_Stop_Count -O--CK 095 095 000 - 5799 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 075 075 000 - 18771 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5355 190 Airflow_Temperature_Cel -O---K 060 031 045 Past 40 194 Temperature_Celsius -O---K 103 074 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 160 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 76 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 76 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 01 01 00 53 00 00 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 d5 b0 0f 81 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 01 d5 00 e0 0f d5 00 81 b0 00 00 00 00:00:57.345 NOP [Reserved subcommand] [OBS-ACS-2] 00 cd ec 0f 81 00 01 00 00 00 00 00 00 00:16:56.270 NOP [Reserved subcommand] [OBS-ACS-2] 00 01 00 00 00 0f bf 00 80 ec 00 00 00 00:00:00.001 NOP [Abort queued commands] Error 75 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 01 01 00 53 00 00 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 57 b0 0f 34 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 01 d5 00 e0 0f 57 00 34 b0 00 00 00 00:00:57.345 NOP [Reserved subcommand] [OBS-ACS-2] 00 50 ec 0f 34 00 01 00 00 00 00 00 00 00:16:36.432 NOP [Reserved subcommand] [OBS-ACS-2] 00 01 00 00 00 0f 3e 00 33 ec 00 00 00 00:00:00.001 NOP [Abort queued commands] Error 74 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e2 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 82 c8 10 21 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 00 10 81 00 21 27 00 00 00 00:00:16.392 NOP [Abort queued commands] 00 79 ef 10 21 00 00 00 00 00 00 00 00 00:17:37.146 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 00 10 79 00 21 27 00 00 00 00:00:00.070 NOP [Abort queued commands] Error 73 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e2 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e9 c8 10 19 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 47 10 15 00 16 e7 00 00 00 00:00:16.392 NOP [Abort queued commands] 06 fd e7 10 15 00 08 00 40 00 00 00 00 00:17:34.229 DATA SET MANAGEMENT 00 78 00 00 c8 10 fc 06 15 ca 00 00 00 00:00:16.128 NOP [Abort queued commands] Error 72 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e2 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 27 c8 0e 4a 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 00 0e 27 00 4a 27 00 00 00 00:00:16.392 NOP [Abort queued commands] 00 1f ef 0e 4a 00 00 00 00 00 00 00 00 00:15:36.479 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 00 0e 1f 00 4a 27 00 00 00 00:00:00.070 NOP [Abort queued commands] Error 71 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e2 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c2 c8 0e 42 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 c0 0e 2f 02 42 ca 00 00 00 00:00:16.392 NOP [Abort queued commands] 02 a4 35 0e 41 00 10 00 88 00 00 00 02 00:15:34.445 [RESERVED] 00 68 00 00 20 0e 94 02 41 ca 00 00 00 00:00:16.472 NOP [Abort queued commands] Error 70 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e2 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 92 c8 0a f6 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 f0 0a 91 06 f6 c8 00 00 00 00:00:16.392 NOP [Abort queued commands] 06 81 c8 0a f6 00 08 00 d8 00 00 00 06 00:11:58.465 DATA SET MANAGEMENT 00 10 00 00 28 0a 74 02 f6 c8 00 00 00 00:00:55.304 NOP [Abort queued commands] Error 69 [20] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e2 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 28 c8 0a e8 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 60 0a 1d 06 e8 c8 00 00 00 00:00:16.392 NOP [Abort queued commands] 00 08 e7 0a e8 00 00 00 ff 00 00 00 00 00:11:54.781 NOP [Reserved subcommand] [OBS-ACS-2] 00 30 00 00 d0 0a 08 06 e8 ca 00 00 00 00:01:05.280 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 44 Celsius Power Cycle Max Temperature: 44 Celsius Lifetime Max Temperature: 69 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/65 Celsius Min/Max Temperature Limit: 1/60 Celsius Temperature History Size (Index): 128 (72) Index Estimated Time Temperature Celsius 73 2016-01-24 18:47 37 ****************** 74 2016-01-24 18:48 37 ****************** 75 2016-01-24 18:49 38 ******************* 76 2016-01-24 18:50 39 ******************** ... ..( 21 skipped). .. ******************** 98 2016-01-24 19:12 39 ******************** 99 2016-01-24 19:13 40 ********************* ... ..( 2 skipped). .. ********************* 102 2016-01-24 19:16 40 ********************* 103 2016-01-24 19:17 41 ********************** 104 2016-01-24 19:18 42 *********************** ... ..( 26 skipped). .. *********************** 3 2016-01-24 19:45 42 *********************** 4 2016-01-24 19:46 45 ************************** 5 2016-01-24 19:47 45 ************************** 6 2016-01-24 19:48 45 ************************** 7 2016-01-24 19:49 42 *********************** ... ..( 8 skipped). .. *********************** 16 2016-01-24 19:58 42 *********************** 17 2016-01-24 19:59 45 ************************** 18 2016-01-24 20:00 45 ************************** 19 2016-01-24 20:01 45 ************************** 20 2016-01-24 20:02 42 *********************** ... ..( 19 skipped). .. *********************** 40 2016-01-24 20:22 42 *********************** 41 2016-01-24 20:23 45 ************************** 42 2016-01-24 20:24 45 ************************** 43 2016-01-24 20:25 45 ************************** 44 2016-01-24 20:26 42 *********************** ... ..( 9 skipped). .. *********************** 54 2016-01-24 20:36 42 *********************** 55 2016-01-24 20:37 ? - 56 2016-01-24 20:38 37 ****************** 57 2016-01-24 20:39 38 ******************* 58 2016-01-24 20:40 39 ******************** 59 2016-01-24 20:41 40 ********************* 60 2016-01-24 20:42 39 ******************** 61 2016-01-24 20:43 40 ********************* 62 2016-01-24 20:44 40 ********************* 63 2016-01-24 20:45 40 ********************* 64 2016-01-24 20:46 39 ******************** ... ..( 4 skipped). .. ******************** 69 2016-01-24 20:51 39 ******************** 70 2016-01-24 20:52 40 ********************* 71 2016-01-24 20:53 41 ********************** 72 2016-01-24 20:54 44 ************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 1016 Vendor specific /dev/sdc === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.9 Device Model: ST3808110AS Serial Number: -- Firmware Version: 3.AAD User Capacity: 80 025 280 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Jan 24 20:54:50 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 27) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 096 006 - 67527333 3 Spin_Up_Time PO---- 099 099 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1190 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 088 060 030 - 755677290 9 Power_On_Hours -O--CK 076 076 000 - 21220 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1097 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 061 051 045 - 39 (Min/Max 38/39) 194 Temperature_Celsius -O---K 039 049 000 - 39 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 063 046 000 - 54261177 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 216 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 216 [15] occurred at disk power-on lifetime: 21189 hours (882 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 de 03 61 03 e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 08:28:38.022 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 08:28:37.962 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 08:28:37.734 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 09 f0 00 50 6e e0 00 08:28:37.670 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 09 f0 00 50 6e e9 00 08:28:35.556 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 215 [14] occurred at disk power-on lifetime: 21189 hours (882 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 de 03 61 03 e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 08:28:33.199 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 08:28:33.198 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 08:28:33.198 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 01 00 09 f8 00 50 af e0 00 08:28:33.198 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 09 f8 00 50 af e0 00 08:28:35.556 READ MULTIPLE EXT Error 214 [13] occurred at disk power-on lifetime: 21182 hours (882 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 00:44:32.521 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 00:44:32.394 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 00:44:32.326 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 09 f0 00 50 6e e0 00 00:44:31.497 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 09 f0 00 50 6e e9 00 00:44:30.689 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 213 [12] occurred at disk power-on lifetime: 21182 hours (882 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 00 00 00 00 00 e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 00:44:32.521 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 00:44:32.394 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 00:44:32.326 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 01 00 09 f8 00 50 af e0 00 00:44:31.497 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 09 f8 00 50 af e0 00 00:44:30.689 READ MULTIPLE EXT Error 212 [11] occurred at disk power-on lifetime: 21149 hours (881 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 04 f4 68 20 68 e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 1d+01:57:23.338 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 1d+01:57:23.278 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 1d+01:57:23.050 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 09 f0 00 50 6e e0 00 1d+01:57:22.978 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 09 f0 00 50 6e e9 00 1d+01:57:20.864 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 211 [10] occurred at disk power-on lifetime: 21149 hours (881 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 04 f4 68 20 68 e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 1d+01:57:18.516 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 1d+01:57:18.516 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 1d+01:57:18.516 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 01 00 09 f8 00 50 af e0 00 1d+01:57:18.516 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 09 f8 00 50 af e0 00 1d+01:57:20.864 READ MULTIPLE EXT Error 210 [9] occurred at disk power-on lifetime: 21003 hours (875 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 07 4e 2d 8b 2d e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 1d+00:00:29.018 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 1d+00:00:28.790 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 1d+00:00:28.718 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 01 01 00 09 f0 00 50 6e e0 00 1d+00:00:26.604 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 01 01 00 09 f0 00 50 6e e9 00 1d+00:00:26.544 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 209 [8] occurred at disk power-on lifetime: 21003 hours (875 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 01 01 00 07 4e 2d 8b 2d e9 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 37 00 00 01 01 00 09 f0 00 50 6e e9 00 1d+00:00:24.246 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 00 00 09 f0 00 50 6e e0 00 1d+00:00:24.246 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 37 00 00 00 00 00 09 f0 00 50 6e e9 00 1d+00:00:24.246 SET NATIVE MAX ADDRESS EXT [OBS-ACS-3] 27 00 00 00 01 00 09 f8 00 50 af e0 00 1d+00:00:26.604 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] 29 00 00 00 01 00 09 f8 00 50 af e0 00 1d+00:00:26.544 READ MULTIPLE EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint T166 Device Model: SAMSUNG HD160HJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: BF100-12 User Capacity: 160 040 803 840 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sun Jan 24 20:54:50 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2975) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 50) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 253 100 051 - 0 3 Spin_Up_Time POS--- 253 253 025 - 4480 4 Start_Stop_Count -O--CK 097 097 000 - 3858 5 Reallocated_Sector_Ct PO--CK 253 253 010 - 0 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 11705 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 253 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 2011 184 End-to-End_Error -O--CK 099 099 000 - 369 187 Reported_Uncorrect -O--CK 053 053 000 - 48 188 Command_Timeout -O--CK 253 253 000 - 0 190 Airflow_Temperature_Cel -O---K 133 106 000 - 35 194 Temperature_Celsius -O---K 133 106 000 - 35 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 7486 196 Reallocated_Event_Count -O--CK 253 253 000 - 0 197 Total_Pending_Sectors -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 1 200 Multi_Zone_Error_Rate -O-R-- 253 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 296 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 296 [7] occurred at disk power-on lifetime: 11377 hours (474 days + 1 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 07 -- 00 49 00 e0 a1 94 00 00 12 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f4 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.118 SECURITY ERASE UNIT f4 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.118 SECURITY ERASE UNIT f4 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.118 SECURITY ERASE UNIT f4 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.766 SECURITY ERASE UNIT 00 89 76 a9 05 00 00 01 50 00 1b 13 79 00:00:11.678 NOP [Reserved subcommand] [OBS-ACS-2] Error 295 [6] occurred at disk power-on lifetime: 11377 hours (474 days + 1 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 48 00 e0 a1 94 00 00 12 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b6 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.118 NV CACHE [OBS-ACS-3] b6 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.118 NV CACHE [OBS-ACS-3] b6 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.118 NV CACHE [OBS-ACS-3] b6 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.766 NV CACHE [OBS-ACS-3] 00 8b 76 a9 05 00 00 01 50 00 1b 13 79 00:00:11.678 NOP [Reserved subcommand] [OBS-ACS-2] Error 294 [5] occurred at disk power-on lifetime: 11377 hours (474 days + 1 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 48 00 e0 a1 94 00 00 12 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 77 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.118 SET DATE & TIME EXT 77 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.118 SET DATE & TIME EXT 77 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.118 SET DATE & TIME EXT 77 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.766 SET DATE & TIME EXT 00 8b 76 a9 05 00 00 01 50 00 1b 13 79 00:00:11.678 NOP [Reserved subcommand] [OBS-ACS-2] Error 293 [4] occurred at disk power-on lifetime: 11377 hours (474 days + 1 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 07 -- 00 39 00 e0 a1 94 00 00 12 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 77 00 00 00 00 27 00 00 e0 00 00 00 00 00:00:00.118 SET DATE & TIME EXT 77 00 00 00 00 ec 00 00 a0 00 00 00 03 00:00:00.118 SET DATE & TIME EXT 77 00 46 00 00 ef 00 00 a0 00 00 00 00 00:00:00.118 SET DATE & TIME EXT 77 00 00 00 00 27 00 00 e0 00 00 00 00 13:58:51.766 SET DATE & TIME EXT 01 11 89 58 91 00 00 11 00 c9 93 02 11 00:00:00.000 [RESERVED] Error 292 [3] occurred at disk power-on lifetime: 12704 hours (529 days + 8 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 89 76 a9 05 00 00 01 50 00 1b 13 79 00:00:11.678 NOP [Reserved subcommand] [OBS-ACS-2] Error 291 [2] occurred at disk power-on lifetime: 11377 hours (474 days + 1 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 80 ec a0 00 00 9d 00 76 3c 01 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 76 00 00 46 03 3c a0 00 ef 00 00 9d 76 00:00:00.000 SEEK [RET-4] 00 00 00 00 00 00 00 00 00 00 00 00 00 30d+12:46:55.648 NOP [Abort queued commands] 9e a9 05 01 1b 00 00 00 13 50 00 03 90 00:00:00.000 [RESERVED] 21 00 00 07 40 00 e0 00 51 00 81 a4 76 23d+00:07:32.721 READ SECTOR(S) [OBS-5] 00 a0 00 3c ec 07 00 76 00 00 9d 81 00 30d+12:46:46.496 NOP [Abort queued commands] Error 290 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 01 1b 00 00 9e 00 00 03 13 50 2d a9 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 71 01 40 00 80 21 00 e0 a4 51 00 1a 00 1d+01:52:36.985 SEEK [RET-4] e0 fe ec 76 9c 00 01 00 80 00 00 00 a0 02:09:33.438 STANDBY IMMEDIATE 00 46 03 00 00 76 fe a0 9c ef 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] a0 00 00 00 00 00 00 00 00 00 00 00 00 02:09:33.438 PACKET Error 289 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 82 -- 2c 00 00 1a a4 51 21 00 e0 71 06 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- bf 76 9c 00 00 e0 00 06 00 82 00 c8 bf 12d+10:15:41.942 [RESERVED] 00 00 00 a0 00 00 76 bf 00 9c ef 00 46 45d+22:45:08.736 NOP [Abort queued commands] bf 00 00 00 00 a0 00 00 00 00 00 ec 00 13:58:51.766 [RESERVED] 00 00 00 00 50 00 9e 00 2d 03 13 00 01 00:00:00.000 NOP [Abort queued commands] 79 00 81 e0 00 71 21 00 1a a4 51 2c 01 5d+08:54:21.833 SEEK [RET-4] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Max Temperature: 35 Celsius Lifetime Max Temperature: 45 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 10/55 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (16) Index Estimated Time Temperature Celsius 17 2016-01-24 18:47 35 **************** ... ..( 7 skipped). .. **************** 25 2016-01-24 18:55 35 **************** 26 2016-01-24 18:56 36 ***************** ... ..( 21 skipped). .. ***************** 48 2016-01-24 19:18 36 ***************** 49 2016-01-24 19:19 37 ****************** 50 2016-01-24 19:20 36 ***************** ... ..( 56 skipped). .. ***************** 107 2016-01-24 20:17 36 ***************** 108 2016-01-24 20:18 35 **************** 109 2016-01-24 20:19 36 ***************** 110 2016-01-24 20:20 36 ***************** 111 2016-01-24 20:21 36 ***************** 112 2016-01-24 20:22 35 **************** 113 2016-01-24 20:23 36 ***************** 114 2016-01-24 20:24 35 **************** 115 2016-01-24 20:25 36 ***************** 116 2016-01-24 20:26 36 ***************** 117 2016-01-24 20:27 36 ***************** 118 2016-01-24 20:28 35 **************** 119 2016-01-24 20:29 36 ***************** 120 2016-01-24 20:30 35 **************** 121 2016-01-24 20:31 36 ***************** 122 2016-01-24 20:32 35 **************** 123 2016-01-24 20:33 35 **************** 124 2016-01-24 20:34 35 **************** 125 2016-01-24 20:35 36 ***************** 126 2016-01-24 20:36 35 **************** 127 2016-01-24 20:37 35 **************** 0 2016-01-24 20:38 ? - 1 2016-01-24 20:39 35 **************** ... ..( 14 skipped). .. **************** 16 2016-01-24 20:54 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific