/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST750LM022 HN-M750MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10001 User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Jan 12 21:46:40 2018 +06 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: (10620) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 177) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 72 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 090 088 025 - 3104 4 Start_Stop_Count -O--CK 098 098 000 - 2690 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 30713 10 Spin_Retry_Count -O--CK 252 252 051 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2741 191 G-Sense_Error_Rate -O---K 100 100 000 - 1849 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 044 000 - 35 (Min/Max 12/56) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 1 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 7110 223 Load_Retry_Count -O--CK 099 099 000 - 1119 225 Load_Cycle_Count -O--CK 082 082 000 - 182034 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 71 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 71 [6] occurred at disk power-on lifetime: 30712 hours (1279 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 2e 05 3b d8 e0 00 Error: UNC 8 sectors at LBA = 0x2e053bd8 = 772094936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e 05 3b d8 e0 08 00:00:00.565 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.565 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.565 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:00.565 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.565 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 70 [5] occurred at disk power-on lifetime: 30712 hours (1279 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 2e 05 3b d8 e0 00 Error: UNC 8 sectors at LBA = 0x2e053bd8 = 772094936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e 05 3b d8 e0 08 00:00:00.563 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.563 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.563 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:00.563 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.563 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 69 [4] occurred at disk power-on lifetime: 30712 hours (1279 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 2e 05 3b d8 e0 00 Error: UNC 8 sectors at LBA = 0x2e053bd8 = 772094936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e 05 3b d8 e0 08 00:00:00.561 READ DMA EXT 25 00 00 00 08 00 00 2e 05 3b 88 e0 08 00:00:00.561 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.561 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.561 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:00.561 SET FEATURES [Set transfer mode] Error 68 [3] occurred at disk power-on lifetime: 30712 hours (1279 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 18 00 00 2e 05 3b 90 e0 00 Error: UNC 24 sectors at LBA = 0x2e053b90 = 772094864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 2e 05 3b 88 e0 08 00:00:00.559 READ DMA EXT 25 00 00 00 08 00 00 2e 05 3b 80 e0 08 00:00:00.559 READ DMA EXT 25 00 00 00 20 00 00 2e 05 3b 40 e0 08 00:00:00.559 READ DMA EXT 25 00 00 00 08 00 00 2e 05 3b 38 e0 08 00:00:00.559 READ DMA EXT 25 00 00 00 40 00 00 2e 05 3a e0 e0 08 00:00:00.559 READ DMA EXT Error 67 [2] occurred at disk power-on lifetime: 30711 hours (1279 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 2e 05 3b d8 e0 00 Error: UNC 8 sectors at LBA = 0x2e053bd8 = 772094936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e 05 3b d8 e0 08 00:00:00.093 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.093 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.093 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:00.093 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.093 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 66 [1] occurred at disk power-on lifetime: 30711 hours (1279 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 2e 05 3b d8 e0 00 Error: UNC 8 sectors at LBA = 0x2e053bd8 = 772094936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e 05 3b d8 e0 08 00:00:00.091 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.091 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.091 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:00.091 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.091 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 65 [0] occurred at disk power-on lifetime: 30711 hours (1279 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 2e 05 3b d8 e0 00 Error: UNC 8 sectors at LBA = 0x2e053bd8 = 772094936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e 05 3b d8 e0 08 00:00:00.089 READ DMA EXT 25 00 00 00 08 00 00 2e 05 3b 88 e0 08 00:00:00.089 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.089 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.089 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:00.089 SET FEATURES [Set transfer mode] Error 64 [7] occurred at disk power-on lifetime: 30711 hours (1279 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 18 00 00 2e 05 3b 90 e0 00 Error: UNC 24 sectors at LBA = 0x2e053b90 = 772094864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 2e 05 3b 88 e0 08 00:00:00.087 READ DMA EXT 25 00 00 00 08 00 00 2e 05 3b 80 e0 08 00:00:00.087 READ DMA EXT 25 00 00 00 20 00 00 2e 05 3b 40 e0 08 00:00:00.087 READ DMA EXT 25 00 00 00 08 00 00 2e 05 3b 38 e0 08 00:00:00.087 READ DMA EXT 25 00 00 00 40 00 00 2e 05 3a e0 e0 08 00:00:00.087 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 27482 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Aborted_by_host [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 34/36 Celsius Lifetime Min/Max Temperature: 13/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (36) Index Estimated Time Temperature Celsius 37 2018-01-12 11:10 35 **************** 38 2018-01-12 11:15 31 ************ 39 2018-01-12 11:20 30 *********** ... ..( 8 skipped). .. *********** 48 2018-01-12 12:05 30 *********** 49 2018-01-12 12:10 31 ************ 50 2018-01-12 12:15 31 ************ 51 2018-01-12 12:20 31 ************ 52 2018-01-12 12:25 32 ************* ... ..( 3 skipped). .. ************* 56 2018-01-12 12:45 32 ************* 57 2018-01-12 12:50 33 ************** ... ..( 5 skipped). .. ************** 63 2018-01-12 13:20 33 ************** 64 2018-01-12 13:25 34 *************** ... ..( 10 skipped). .. *************** 75 2018-01-12 14:20 34 *************** 76 2018-01-12 14:25 35 **************** ... ..( 16 skipped). .. **************** 93 2018-01-12 15:50 35 **************** 94 2018-01-12 15:55 34 *************** 95 2018-01-12 16:00 35 **************** 96 2018-01-12 16:05 34 *************** ... ..( 11 skipped). .. *************** 108 2018-01-12 17:05 34 *************** 109 2018-01-12 17:10 33 ************** ... ..( 6 skipped). .. ************** 116 2018-01-12 17:45 33 ************** 117 2018-01-12 17:50 32 ************* ... ..( 3 skipped). .. ************* 121 2018-01-12 18:10 32 ************* 122 2018-01-12 18:15 31 ************ ... ..( 3 skipped). .. ************ 126 2018-01-12 18:35 31 ************ 127 2018-01-12 18:40 30 *********** 0 2018-01-12 18:45 30 *********** 1 2018-01-12 18:50 30 *********** 2 2018-01-12 18:55 29 ********** 3 2018-01-12 19:00 32 ************* 4 2018-01-12 19:05 33 ************** 5 2018-01-12 19:10 33 ************** 6 2018-01-12 19:15 34 *************** ... ..( 8 skipped). .. *************** 15 2018-01-12 20:00 34 *************** 16 2018-01-12 20:05 33 ************** ... ..( 3 skipped). .. ************** 20 2018-01-12 20:25 33 ************** 21 2018-01-12 20:30 32 ************* 22 2018-01-12 20:35 31 ************ 23 2018-01-12 20:40 31 ************ 24 2018-01-12 20:45 32 ************* 25 2018-01-12 20:50 34 *************** 26 2018-01-12 20:55 35 **************** 27 2018-01-12 21:00 34 *************** 28 2018-01-12 21:05 35 **************** 29 2018-01-12 21:10 34 *************** 30 2018-01-12 21:15 34 *************** 31 2018-01-12 21:20 35 **************** 32 2018-01-12 21:25 36 ***************** 33 2018-01-12 21:30 36 ***************** 34 2018-01-12 21:35 36 ***************** 35 2018-01-12 21:40 35 **************** 36 2018-01-12 21:45 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific