Probe #bd9367f2b7 of ASRock FM2A88X Extreme6+ Desktop Computer

Log: smartctl

/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.16.18-200.fc35.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT1000MX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M3CR023 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 27 03:40:27 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 12331 12 Power_Cycle_Count -O--CK 100 100 000 - 27 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 063 063 000 - 569 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 6 180 Unused_Reserve_NAND_Blk PO--CK 000 000 000 - 39 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 056 033 000 - 44 (Min/Max 0/67) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 202 Percent_Lifetime_Remain ----CK 063 063 001 - 37 206 Write_Error_Rate -OSR-- 100 100 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 91044550188 247 Host_Program_Page_Count -O--CK 100 100 000 - 1495127327 248 FTL_Program_Page_Count -O--CK 100 100 000 - 15133055686 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 64 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Completed [00% left] (0-65535) Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 44 Celsius Power Cycle Min/Max Temperature: 37/67 Celsius Lifetime Min/Max Temperature: 0/67 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: 0/100 Celsius Temperature History Size (Index): 128 (33) Index Estimated Time Temperature Celsius 34 2022-10-27 01:33 42 *********************** 35 2022-10-27 01:34 42 *********************** 36 2022-10-27 01:35 44 ************************* 37 2022-10-27 01:36 42 *********************** ... ..( 2 skipped). .. *********************** 40 2022-10-27 01:39 42 *********************** 41 2022-10-27 01:40 44 ************************* 42 2022-10-27 01:41 42 *********************** 43 2022-10-27 01:42 42 *********************** 44 2022-10-27 01:43 45 ************************** 45 2022-10-27 01:44 42 *********************** ... ..( 7 skipped). .. *********************** 53 2022-10-27 01:52 42 *********************** 54 2022-10-27 01:53 44 ************************* 55 2022-10-27 01:54 42 *********************** ... ..( 2 skipped). .. *********************** 58 2022-10-27 01:57 42 *********************** 59 2022-10-27 01:58 44 ************************* 60 2022-10-27 01:59 42 *********************** 61 2022-10-27 02:00 42 *********************** 62 2022-10-27 02:01 42 *********************** 63 2022-10-27 02:02 44 ************************* 64 2022-10-27 02:03 42 *********************** 65 2022-10-27 02:04 44 ************************* 66 2022-10-27 02:05 44 ************************* 67 2022-10-27 02:06 42 *********************** ... ..( 4 skipped). .. *********************** 72 2022-10-27 02:11 42 *********************** 73 2022-10-27 02:12 45 ************************** 74 2022-10-27 02:13 42 *********************** ... ..( 2 skipped). .. *********************** 77 2022-10-27 02:16 42 *********************** 78 2022-10-27 02:17 44 ************************* 79 2022-10-27 02:18 44 ************************* 80 2022-10-27 02:19 42 *********************** 81 2022-10-27 02:20 42 *********************** 82 2022-10-27 02:21 44 ************************* 83 2022-10-27 02:22 42 *********************** ... ..( 13 skipped). .. *********************** 97 2022-10-27 02:36 42 *********************** 98 2022-10-27 02:37 44 ************************* 99 2022-10-27 02:38 42 *********************** ... ..( 10 skipped). .. *********************** 110 2022-10-27 02:49 42 *********************** 111 2022-10-27 02:50 44 ************************* 112 2022-10-27 02:51 42 *********************** 113 2022-10-27 02:52 42 *********************** 114 2022-10-27 02:53 47 **************************** 115 2022-10-27 02:54 42 *********************** 116 2022-10-27 02:55 42 *********************** 117 2022-10-27 02:56 44 ************************* 118 2022-10-27 02:57 42 *********************** ... ..( 8 skipped). .. *********************** 127 2022-10-27 03:06 42 *********************** 0 2022-10-27 03:07 44 ************************* 1 2022-10-27 03:08 42 *********************** 2 2022-10-27 03:09 42 *********************** 3 2022-10-27 03:10 42 *********************** 4 2022-10-27 03:11 44 ************************* 5 2022-10-27 03:12 44 ************************* 6 2022-10-27 03:13 42 *********************** ... ..( 6 skipped). .. *********************** 13 2022-10-27 03:20 42 *********************** 14 2022-10-27 03:21 44 ************************* 15 2022-10-27 03:22 42 *********************** ... ..( 7 skipped). .. *********************** 23 2022-10-27 03:30 42 *********************** 24 2022-10-27 03:31 47 **************************** 25 2022-10-27 03:32 42 *********************** 26 2022-10-27 03:33 42 *********************** 27 2022-10-27 03:34 44 ************************* 28 2022-10-27 03:35 42 *********************** 29 2022-10-27 03:36 44 ************************* 30 2022-10-27 03:37 42 *********************** ... ..( 2 skipped). .. *********************** 33 2022-10-27 03:40 42 *********************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 27 --- Lifetime Power-On Resets 0x01 0x010 4 12331 --- Power-on Hours 0x01 0x018 6 850236972 --- Logical Sectors Written 0x01 0x020 6 746176326 --- Number of Write Commands 0x01 0x028 6 15621931 --- Logical Sectors Read 0x01 0x030 6 631972378 --- Number of Read Commands 0x01 0x038 6 4294967296 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 7 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 44 --- Current Temperature 0x05 0x010 1 42 --- Average Short Term Temperature 0x05 0x018 1 42 --- Average Long Term Temperature 0x05 0x020 1 67 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 42 --- Highest Average Short Term Temperature 0x05 0x038 1 39 --- Lowest Average Short Term Temperature 0x05 0x040 1 60 --- Highest Average Long Term Temperature 0x05 0x048 1 39 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 47 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1052 --- Number of Hardware Resets 0x06 0x010 4 132 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 37 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 20 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.16.18-200.fc35.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 27 03:40:27 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (40380) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 405) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 187 172 021 - 5616 4 Start_Stop_Count -O--CK 100 100 000 - 49 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 050 049 000 - 36530 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 49 192 Power-Off_Retract_Count -O--CK 200 200 000 - 21 193 Load_Cycle_Count -O--CK 194 194 000 - 20073 194 Temperature_Celsius -O---K 113 102 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 34/47 Celsius Lifetime Min/Max Temperature: 2/48 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (65) Index Estimated Time Temperature Celsius 66 2022-10-26 19:43 37 ****************** ... ..(476 skipped). .. ****************** 65 2022-10-27 03:40 37 ****************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 49 --- Lifetime Power-On Resets 0x01 0x010 4 36530 --- Power-on Hours 0x01 0x018 6 10813461257 --- Logical Sectors Written 0x01 0x020 6 142973679 --- Number of Write Commands 0x01 0x028 6 22398074146 --- Logical Sectors Read 0x01 0x030 6 468711399 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 43758 --- Spindle Motor Power-on Hours 0x03 0x010 4 34035 --- Head Flying Hours 0x03 0x018 4 20095 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 13 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 35 --- Average Short Term Temperature 0x05 0x018 1 36 --- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x030 1 45 --- Highest Average Short Term Temperature 0x05 0x038 1 26 --- Lowest Average Short Term Temperature 0x05 0x040 1 40 --- Highest Average Long Term Temperature 0x05 0x048 1 29 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 878 --- Number of Hardware Resets 0x06 0x010 4 1572 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 21 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 19266593 Vendor specific /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.16.18-200.fc35.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST3000DM001-1CH166 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC24 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Thu Oct 27 03:40:28 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 342) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 089 086 006 - 56277287 3 Spin_Up_Time PO---- 095 094 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 137 5 Reallocated_Sector_Ct PO--CK 088 088 010 - 15952 7 Seek_Error_Rate POSR-- 048 039 030 - 1644995738240 9 Power_On_Hours -O--CK 015 015 000 - 75175 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 137 183 Runtime_Bad_Block -O--CK 092 092 000 - 8 184 End-to-End_Error -O--CK 099 099 099 NOW 1 187 Reported_Uncorrect -O--CK 001 001 000 - 779 188 Command_Timeout -O--CK 001 001 000 - 1853 65535 65535 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 048 045 - 37 (Min/Max 33/48) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 67 193 Load_Cycle_Count -O--CK 001 001 000 - 818339 194 Temperature_Celsius -O---K 037 052 000 - 37 (0 13 0 0 0) 197 Current_Pending_Sector -O--C- 001 001 000 - 18552 198 Offline_Uncorrectable ----C- 001 001 000 - 18552 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 19911h+04m+31.117s 241 Total_LBAs_Written ------ 100 253 000 - 11385995080 242 Total_LBAs_Read ------ 100 253 000 - 17394213112 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 779 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 779 [18] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 49 a3 b0 00 00 Error: UNC at LBA = 0x15d49a3b0 = 5860074416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 49 a3 b0 40 00 00:27:16.726 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:27:16.666 NOP [Abort queued commands] 25 00 00 80 00 00 01 5d 48 23 b0 40 00 00:27:12.720 READ DMA EXT 25 00 00 80 00 00 01 5d 47 a3 b0 40 00 00:27:12.532 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:27:12.471 NOP [Abort queued commands] Error 778 [17] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 49 47 c0 00 00 Error: UNC at LBA = 0x15d4947c0 = 5860050880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 48 23 b0 40 00 00:27:12.720 READ DMA EXT 25 00 00 80 00 00 01 5d 47 a3 b0 40 00 00:27:12.532 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:27:12.471 NOP [Abort queued commands] 25 00 00 80 00 00 01 5d 47 23 b0 40 00 00:27:08.814 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:27:08.754 NOP [Abort queued commands] Error 777 [16] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 47 23 b0 00 00 Error: UNC at LBA = 0x15d4723b0 = 5859910576 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 47 23 b0 40 00 00:27:08.814 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:27:08.754 NOP [Abort queued commands] 25 00 00 80 00 00 01 5d 45 a3 b0 40 00 00:27:04.800 READ DMA EXT 25 00 00 80 00 00 01 5d 45 23 b0 40 00 00:27:04.568 READ DMA EXT 25 00 00 80 00 00 01 5d 44 a3 b0 40 00 00:27:04.291 READ DMA EXT Error 776 [15] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 46 c6 60 00 00 Error: UNC at LBA = 0x15d46c660 = 5859886688 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 45 a3 b0 40 00 00:27:04.800 READ DMA EXT 25 00 00 80 00 00 01 5d 45 23 b0 40 00 00:27:04.568 READ DMA EXT 25 00 00 80 00 00 01 5d 44 a3 b0 40 00 00:27:04.291 READ DMA EXT 25 00 00 80 00 00 01 5d 44 23 b0 40 00 00:27:04.063 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:27:03.986 NOP [Abort queued commands] Error 775 [14] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 43 a3 b0 00 00 Error: UNC at LBA = 0x15d43a3b0 = 5859681200 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 43 a3 b0 40 00 00:27:00.775 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:27:00.619 NOP [Abort queued commands] 25 00 00 80 00 00 01 5d 42 23 b0 40 00 00:26:57.131 READ DMA EXT 25 00 00 80 00 00 01 5d 41 a3 b0 40 00 00:26:56.937 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:26:56.877 NOP [Abort queued commands] Error 774 [13] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 43 67 50 00 00 Error: UNC at LBA = 0x15d436750 = 5859665744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 42 23 b0 40 00 00:26:57.131 READ DMA EXT 25 00 00 80 00 00 01 5d 41 a3 b0 40 00 00:26:56.937 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:26:56.877 NOP [Abort queued commands] 25 00 00 80 00 00 01 5d 41 23 b0 40 00 00:26:53.195 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:26:53.134 NOP [Abort queued commands] Error 773 [12] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 41 23 b0 00 00 Error: UNC at LBA = 0x15d4123b0 = 5859517360 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 41 23 b0 40 00 00:26:53.195 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:26:53.134 NOP [Abort queued commands] 25 00 00 80 00 00 01 5d 3e a3 b0 40 00 00:26:48.729 READ DMA EXT 25 00 00 80 00 00 01 5d 3e 23 b0 40 00 00:26:48.527 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:26:48.466 NOP [Abort queued commands] Error 772 [11] occurred at disk power-on lifetime: 4282 hours (178 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 5d 41 00 70 00 00 Error: UNC at LBA = 0x15d410070 = 5859508336 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 80 00 00 01 5d 3e a3 b0 40 00 00:26:48.729 READ DMA EXT 25 00 00 80 00 00 01 5d 3e 23 b0 40 00 00:26:48.527 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:26:48.466 NOP [Abort queued commands] 25 00 00 80 00 00 01 5d 3d a3 b0 40 00 00:26:44.813 READ DMA EXT 00 00 00 00 00 00 00 00 00 00 00 00 ff 00:26:44.753 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 33/48 Celsius Lifetime Min/Max Temperature: 13/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 34635 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.16.18-200.fc35.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red (SMR) Device Model: WDC WD60EFAX-68SHWN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 27 03:41:39 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7380) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 241) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 235 229 021 - 3241 4 Start_Stop_Count -O--CK 100 100 000 - 9 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 079 079 000 - 15668 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 9 192 Power-Off_Retract_Count -O--CK 200 200 000 - 2 193 Load_Cycle_Count -O--CK 200 200 000 - 74 194 Temperature_Celsius -O---K 121 110 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 291 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 78 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 25/40 Celsius Lifetime Min/Max Temperature: 16/40 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/65 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (88) Index Estimated Time Temperature Celsius 89 2022-10-26 19:44 29 ********** ... ..(476 skipped). .. ********** 88 2022-10-27 03:41 29 ********** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 9 --- Lifetime Power-On Resets 0x01 0x010 4 15668 --- Power-on Hours 0x01 0x018 6 4724627073 --- Logical Sectors Written 0x01 0x020 6 5889578 --- Number of Write Commands 0x01 0x028 6 12999368178 --- Logical Sectors Read 0x01 0x030 6 204888042 --- Number of Read Commands 0x01 0x038 6 570225152 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 15525 --- Spindle Motor Power-on Hours 0x03 0x010 4 15006 --- Head Flying Hours 0x03 0x018 4 77 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 2 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 28 --- Average Short Term Temperature 0x05 0x018 1 30 --- Average Long Term Temperature 0x05 0x020 1 40 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 38 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 33 --- Highest Average Long Term Temperature 0x05 0x048 1 25 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 65 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 250 --- Number of Hardware Resets 0x06 0x010 4 139 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == 0xff 0x008 7 0 --- Vendor Specific 0xff 0x010 7 0 --- Vendor Specific 0xff 0x018 7 0 --- Vendor Specific |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 20 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 24 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 19266791 Vendor specific /dev/sdi smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.16.18-200.fc35.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Ultrastar He10/12 Device Model: WDC WD100EMAZ-00WJTA0 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: 83.H0A83 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 27 03:41:40 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 164 (intermediate level without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 93) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1079) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance --S--- 131 131 054 - 105 3 Spin_Up_Time POS--- 152 152 024 - 432 (Average 431) 4 Start_Stop_Count -O--C- 100 100 000 - 1988 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate -O-R-- 100 100 067 - 0 8 Seek_Time_Performance --S--- 128 128 020 - 18 9 Power_On_Hours -O--C- 100 100 000 - 5651 10 Spin_Retry_Count -O--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1988 22 Helium_Level PO---K 100 100 025 - 100 192 Power-Off_Retract_Count -O--CK 099 099 000 - 2171 193 Load_Cycle_Count -O--C- 099 099 000 - 2171 194 Temperature_Celsius -O---- 240 240 000 - 27 (Min/Max 15/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 5501 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 25/27 Celsius Lifetime Min/Max Temperature: 15/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/65 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (4) Index Estimated Time Temperature Celsius 5 2022-10-27 01:34 32 ************* 6 2022-10-27 01:35 32 ************* 7 2022-10-27 01:36 32 ************* 8 2022-10-27 01:37 33 ************** ... ..( 2 skipped). .. ************** 11 2022-10-27 01:40 33 ************** 12 2022-10-27 01:41 34 *************** ... ..( 2 skipped). .. *************** 15 2022-10-27 01:44 34 *************** 16 2022-10-27 01:45 35 **************** ... ..( 2 skipped). .. **************** 19 2022-10-27 01:48 35 **************** 20 2022-10-27 01:49 36 ***************** ... ..( 3 skipped). .. ***************** 24 2022-10-27 01:53 36 ***************** 25 2022-10-27 01:54 37 ****************** 26 2022-10-27 01:55 37 ****************** 27 2022-10-27 01:56 25 ****** 28 2022-10-27 01:57 25 ****** 29 2022-10-27 01:58 26 ******* 30 2022-10-27 01:59 26 ******* 31 2022-10-27 02:00 27 ******** 32 2022-10-27 02:01 27 ******** 33 2022-10-27 02:02 28 ********* 34 2022-10-27 02:03 28 ********* 35 2022-10-27 02:04 29 ********** 36 2022-10-27 02:05 29 ********** 37 2022-10-27 02:06 30 *********** 38 2022-10-27 02:07 30 *********** 39 2022-10-27 02:08 31 ************ 40 2022-10-27 02:09 31 ************ 41 2022-10-27 02:10 31 ************ 42 2022-10-27 02:11 32 ************* 43 2022-10-27 02:12 32 ************* 44 2022-10-27 02:13 32 ************* 45 2022-10-27 02:14 33 ************** ... ..( 2 skipped). .. ************** 48 2022-10-27 02:17 33 ************** 49 2022-10-27 02:18 34 *************** 50 2022-10-27 02:19 34 *************** 51 2022-10-27 02:20 34 *************** 52 2022-10-27 02:21 35 **************** ... ..( 2 skipped). .. **************** 55 2022-10-27 02:24 35 **************** 56 2022-10-27 02:25 36 ***************** 57 2022-10-27 02:26 36 ***************** 58 2022-10-27 02:27 36 ***************** 59 2022-10-27 02:28 25 ****** 60 2022-10-27 02:29 26 ******* 61 2022-10-27 02:30 26 ******* 62 2022-10-27 02:31 27 ******** 63 2022-10-27 02:32 28 ********* 64 2022-10-27 02:33 28 ********* 65 2022-10-27 02:34 29 ********** 66 2022-10-27 02:35 29 ********** 67 2022-10-27 02:36 30 *********** 68 2022-10-27 02:37 30 *********** 69 2022-10-27 02:38 30 *********** 70 2022-10-27 02:39 31 ************ 71 2022-10-27 02:40 31 ************ 72 2022-10-27 02:41 32 ************* ... ..( 2 skipped). .. ************* 75 2022-10-27 02:44 32 ************* 76 2022-10-27 02:45 33 ************** 77 2022-10-27 02:46 33 ************** 78 2022-10-27 02:47 33 ************** 79 2022-10-27 02:48 34 *************** 80 2022-10-27 02:49 34 *************** 81 2022-10-27 02:50 34 *************** 82 2022-10-27 02:51 35 **************** ... ..( 2 skipped). .. **************** 85 2022-10-27 02:54 35 **************** 86 2022-10-27 02:55 36 ***************** ... ..( 2 skipped). .. ***************** 89 2022-10-27 02:58 36 ***************** 90 2022-10-27 02:59 37 ****************** ... ..( 3 skipped). .. ****************** 94 2022-10-27 03:03 37 ****************** 95 2022-10-27 03:04 38 ******************* 96 2022-10-27 03:05 25 ****** 97 2022-10-27 03:06 26 ******* 98 2022-10-27 03:07 26 ******* 99 2022-10-27 03:08 27 ******** 100 2022-10-27 03:09 28 ********* 101 2022-10-27 03:10 28 ********* 102 2022-10-27 03:11 29 ********** 103 2022-10-27 03:12 29 ********** 104 2022-10-27 03:13 30 *********** 105 2022-10-27 03:14 30 *********** 106 2022-10-27 03:15 30 *********** 107 2022-10-27 03:16 31 ************ 108 2022-10-27 03:17 31 ************ 109 2022-10-27 03:18 32 ************* 110 2022-10-27 03:19 32 ************* 111 2022-10-27 03:20 32 ************* 112 2022-10-27 03:21 33 ************** ... ..( 2 skipped). .. ************** 115 2022-10-27 03:24 33 ************** 116 2022-10-27 03:25 34 *************** 117 2022-10-27 03:26 34 *************** 118 2022-10-27 03:27 34 *************** 119 2022-10-27 03:28 35 **************** ... ..( 2 skipped). .. **************** 122 2022-10-27 03:31 35 **************** 123 2022-10-27 03:32 36 ***************** ... ..( 2 skipped). .. ***************** 126 2022-10-27 03:35 36 ***************** 127 2022-10-27 03:36 37 ****************** 0 2022-10-27 03:37 25 ****** 1 2022-10-27 03:38 26 ******* 2 2022-10-27 03:39 27 ******** 3 2022-10-27 03:40 27 ******** 4 2022-10-27 03:41 31 ************ SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1988 --- Lifetime Power-On Resets 0x01 0x010 4 5651 --- Power-on Hours 0x01 0x018 6 9195253058 --- Logical Sectors Written 0x01 0x020 6 20838952 --- Number of Write Commands 0x01 0x028 6 1560586794 --- Logical Sectors Read 0x01 0x030 6 102679537 --- Number of Read Commands 0x01 0x038 6 20347094600 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 5642 --- Spindle Motor Power-on Hours 0x03 0x010 4 5642 --- Head Flying Hours 0x03 0x018 4 2171 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 4 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 27 --- Current Temperature 0x05 0x010 1 31 N-- Average Short Term Temperature 0x05 0x018 1 32 N-- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 46 N-- Highest Average Short Term Temperature 0x05 0x038 1 21 N-- Lowest Average Short Term Temperature 0x05 0x040 1 42 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 65 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 0 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS


Hardware for Linux and BSD

GitHub